ender 3 s1 octoprint 3d models

Don't try add-ons. Ditch the stock cable guide completely. Save your ribbon cable from premature wear. I had to alter the retainer clips slightly to get it to fit. Pull the retainers out and snip the outer nubs off. ...From there everything should...

Couldn't find one, so I made one on Tinkercad.

This is a remix of the project from here https://www.thingiverse.com/thing:5767800 by bensoneh. The issue with the original thingy was that the display mount was too close to the pi case so the top cover would not fit. Also the screw holes seems...

Loved the engineering, but wanted a more diffused light, so a little PLA transparent and here ya go!

This model is designed to fit the extruder in one piece. It is an experimental design but it works perfectly. Then I will release a new version. Print fan side down. ... layer: 0.20 infill: 10% supports: yes

Those mounting frames are intended to be used with the Neoteck DTI Digital Dial Indicator (https://www.amazon.com/gp/product/B07DFLTTQ1). It has a resolution of 0.001mm, so when you finish, your printer should be pretty leveled. You can modify the...

As the Spatula doesn't fit in my tray in the printer and I wanted to have it accessible I printed the holder by irrational0. Now I rearranged my printer and had no room to use the holder, but needed it to mount on the left side of my printer.Easy...

This remix makes room for a 48mm Y axis stepper motor.   I did test print it at 5mm thick with ASA and it worked, but tigtening the bedscrews will bend the corners upward.  It needs to be made out of aluminum. ...  I used https://sendcutsend.com/ to...

I created this remix without the sidewalls in order to save time in printing and use less filament. But I still haven't printed a proof to evaluate the result. ... If you print it, share your result.

<p>Guides à coller au double face sous votre plateau afin de placer correctement et rapidement votre plaque PEI.</p><p>S'adapte surement à un grand nombre d'imprimantes.</p><p>Je les ai placés seulement à l'arrière du lit pour donner la position mais...

Recommended Print Settings: Outlines 3x Important Note: The Mount on the Bottom is higher as the Original Feet, its visible on the Picture Make sure to lift up the printer with additional feet like anti vibration blocks. My design requieres no...

I wanted to mount my RPi 4 running Klipper where the touchscreen After printing it should slot into the touchscreen mount just fine - the Pi can be mounted using M2.5 screws or standoffs Enjoy!

This is a Z-axis camera mount which gives a rear view of the print bed, since the front and sides are blocked by my upgraded cooling vents. It is very stable and holds my heavy camera with no issues. ... Filament: PETG Layer Height: 0.2 ...

I loved the minimalist bed handle by schroedaa, but it was a bit too tall and the parts cooling fan was impacting the handle, so I trimmed the handle pull down by 5mm. ...Everything clears fine now and there's still enough handle to pull on.

This is an adaptor to attach your Sprite or Sprite Pro extruder to an MGN12H linear rail. Fitting _________ Remove the extruder from the mount. Remove the belts from the slots, then loosen the screws securing the lower wheel, then slip the...

Simple replacement for the original bed handle. Designed it for my IKEA Lack Enclosure because the standard was too long for my purpose. You can use the original screws. ...

Extruder ribbon cable stress relief mod , doesn`t hit the gantry while homing or reaching the max z height , easy to install & fits perfectly let me know if it works for you ! ...:D

This is a remix to print in less then 5h

The light is Amazon: https://www.amazon.com/dp/B08VDH1GJV

This puts your ribboncable on the front instead of the back and coupled together with my other model that protects the turning of the ribboncable on the contact make this great

I printed this in PETG. This support prevents the rear bed cable snagging on the rear stepper motor. ...You will need 2 small cable ties and a hot glue gun.

There are other models made by different authors, mine has two differences.different shape of endstop pcblow profile, doesn't touch the bed with silicon spacersfill free to modify on onshape

Idea came from https://www.thingiverse.com/thing:5444181 but I found the clip too narrow for the cable so made a new clip with more allowances from scratch that fits much better. Print it in the same orientation as in the images, not as it comes...

This is a full CAD recreation of the bedside clamp as the original had messy geometry. ...Moreover, it was too short using the description provided with the referenced parts, which was: > *You will need 1x Bed clamp, 1x Frame clamp, 18x Chain link,...

FIRST OF ALL: You are not forced to print both part. You can keep one of the two "stock". The cooling duct is based on the "Stock Creality Sprite Fan Double Duct" from Sorkin and adapt it to fit a blower fan 5020 24VDC on it. It is super quiet and...

Hello, As i printed this drawer before i wanted a clean and neat solution for the Nozzles and this is what i came up. ... Best regards

Torre modificada para PRUSA Slicer, la cargue con un perfil de 0.24 un poco mas acelerado de lo normal que me dio muy buenos resultados, el proyecyo que les comparto ya tiene los cambios de temperatura cargados. Saludos! ...

<p>Material: PLA</p><p>Infill: 15%</p><p>&nbsp;</p>

I needed a mount for the C920 and liked the other design, however the C920 base is a little wider. Factory screws hold this in place, although I did notice a slight spread apart where it attaches to the printer. ... Just added a new version, more...

This is a mounting point for the Articulating Raspberry Pi Camera Mount. ... Because it has only a small mounting area it is not sufficient for heavy load.