ender 3 v2 base wobble 3d models

Since I recently installed a BLTouch on my Ender 3 Pro, I no longer need the mechanical Z-axis end switch. I have now converted it into a filament runout sensor and designed a small housing for it. This one is a modification of my 1st version...

Print Settings Printer Brand: Creality Printer: Ender 3 Rafts: No Supports: Yes Infill: 15% Notes: Printed with most of the flat side on the bed, a little support is needed to create the v-slot rails.The object should be orientated correct already...

I only used this for tuning input shaper, then removed the mount.This model uses the space from here: BLTouch Spacer/Screw Cover for Ender 3 Pro by onpdm - ThingiverseI don't have a photo of it mounted, I'd removed it and started a new print by the...

I am no expert on electronics, so I don't want to add a how to connect the cable to the 24v ender 3 power supply and ruin your printer section. I just connect the + - cables to the output and it magically works.. I added this...

You do have to be careful not to tighten these screws because you will put stress on your leadscrew and cause printing issues. Print Settings Printer Brand: Creality Printer: Ender 3 Rafts: No Supports: Yes Resolution: 0.12 Infill: 10% Filament:...

(this is why there is a space near the SD card slot) Print Settings Printer Brand: Creality Printer: Ender 3 Rafts: Doesn't Matter Supports: Yes Resolution: 0.2 Infill: your choice Filament: Sunlu PETG/PLA/ABS any Notes: Fan mount is for a...

Remixed the bottom connector from "Cable chains and connectors for Ender3 V2 - full set" by Beh01der. ...On the original part Y chain was connected too close to power switch and was not aligned with plate connector.

This is a remix of the V2 version which has more clearance. The offset should be untouched X-43.65 Y-10. ...Added a cutout for the cable.</p>

I lengthened the mounting rod and changed the holder to work with the V2 Raspberry Pi camera. ... I also modified the [Twist in Cable Holder](https://www.thingiverse.com/thing:2816969) to work with the Raspberry Pi camera ribbon cable.

I've created a cover for the X-axis motor on the Ender3 v2 (to hide the QRcode). Feel free to ask if you want another design. ... No specific details for the parameters of the printer.

A guard over the PSU wire terminal . ... This is part of my attempt for better cable management of the Ender3 V2 https://www.thingiverse.com/thing:4761365 https://www.thingiverse.com/thing:4768402

[DEPRECIATED] A new version is in the works with better accuracy measured it best I could and flipped it ~ and stretched it Printed and functional v3 because v1 wasn't long enough and v2 wasn't wide enough to fit the screen v3 is a little too wide...

This is a filament spool adaptor for an Ender 3V2. ...Made to decrease the ID of the spool on the stock mount so the extruder motor has less resistance and vibrations.

This is a bracket I designed that moves the screen from the right to the left side of the Ender 3v2. I printed with PLA 20% infill. ...Used ShapR3D software on iPad.

I needed the Ender 3V2 LCD to be on the left side to suit my desk setup, and wanted it "floating" to be able to move it late to be outside an enclosure (when I finally make one).

It is just a tool holder for the Ender series but with a sliding mount instead of press-fit, and some SD/microSD card slots.Minimal supports needed, just for the sliders.

This is a bracket I designed that moves the screen from the right to the left side of the Ender 3v2. I printed with PLA 20% infill. ...Used ShapR3D software on iPad.

reverse bowden to voron switchwire, specifically to the ender converted to voron switchwire, I couldn't find a corresponding file anywhere, so I created this one. In my case it helped with the zebra on prints. ...

This is an X-Axis mount made to fit the Ender 3V2 X axis arm/tensioner. ...I used it as a way to mount a camera for taking time lapses that moved up with the Z height.

I needed the Ender 3V2 LCD to be on the left side to suit my desk setup, and wanted it "floating" to be able to move it late to be outside an enclosure (when I finally make one). ...

... ... Plan on printing new bottom plates for larger fans for the Ender 3v2, but needed some quality feet to elevate. Remix, blending: https://www.thingiverse.com/thing:4603075 -and- https://www.thingiverse.com/thing:1307300 Left and right feet.

(Description in german below // Deutschsprachige Beschreibung folgt unten)Since I recently mounted a BLTouch on my Ender 3 Pro, I no longer need the mechanical Z-axis end switch. I have now converted it into a filament runout sensor and designed a...

I forgot to add a chanfer in the fan holes (the screws might not get perfectly flat with the print) PS: I used this feet -&gt; https://www.thingiverse.com/thing:4721832 Print Settings Printer Brand: Creality Printer: Ender 3 Rafts: No Supports: No...

I'm running a modified version of the Mini Me cooling duct and it clears just fine. While I was redrawing this, I also added a rib for support, and a couple of through holes to make installation easier. Prints great with no supports. Print Settings...

... Used mrmt32 original lid without any issue. Print Settings Printer Brand: Creality Printer: Ender 3 Rafts: No Supports: Yes Resolution: .2 Infill: Doesn't matter, its all skin/walls Filament: Overture PLA Black Category: 3D Printer Parts

This is a re-design of the Creality Ender 3 Pro dual drawer by DWS_Design - https://www.thingiverse.com/thing:3416444 Somehow, the original design didn't fit my printer correctly - one of the bolts on the bottom of the Y-axis wheel kept scraping the...

Only really useful to those who have added a version 2 vertical screen to their ender 3 max. I rarely use the screen as I use a pi zero 2w and octoprint for the majority of my interactions with the printer. I decided on a more compact layout and...

This is intensional so the printed bracket do not wobble during printing. Drill/Ream the holes with a 8mm drill bit, drill slowly so plastic will not melt during drilling. the cylindrical tube should fit holes perfectly, fit should not be loose or...

This redesign improves stability significantly, eliminating the wobbling caused by a broken fan blade in the previous model. The arm of the camera now rests firmly on the build plate, eliminating the annoying rattling sound that plagued my earlier...

This is a TinkerCAD remix for use on Ender3 V2 - to reduce noise and maximize air flow: bigger intake fan opening with chamfered edge still no fan guard (not a good choice, if you have pets or young children) more exhaust side ports - relocated...