ender 3 v2 base wobble 3d models

This Thing is a LED Light holder for the Ender 3 V2 and Ender 5 Petsfang Bullseye Duct Petsfang: https://www.thingiverse.com/thing:2759439 I have mounted a 24 Volt COB LED Strip of 5cm on this Holder You need 2 Screws M2x20 and 2 nuts M2 to mount the...

I couldnt find anything suitable for the adxl v2.0 that uses USBC, so i threw these together.i have the creality direct drive, (non sprite), and for the x axis i unscrewed the bottom front screw of the fan on the right side of the extruder, and then...

... or getting caught on the PSU. ...Works best with low socket or button socket head M5 screws. This is part of my attempt for better cable management of the Ender3 V2 https://www.thingiverse.com/thing:4761365 https://www.thingiverse.com/thing:4774312

some changes on the electronics enlcosure and the screen is bigger so frame needed adapting.great upgrade for an ender3 MKS Robin nano v3 available now I did this for v2 not sure about the changes on the board dimensions I dont think there are any

Just a simple hanger to hold up the gantry. ...I got tired of trying to find a way to prop up or tie up the x axis gantry when I wanted to change the nozzle or had to clean a blockage. May fit other printers, I have only tried on my E3 v2.

some changes on the electronics enlcosure and the screen is bigger so frame needed adapting.great upgrade for an ender3 MKS Robin nano v3 available now I did this for v2 not sure about the changes on the board dimensions I dont think there are any

A Knurled Z-Axis Knob following the ["Knurled Ender3 V2 Belt Tensioner Knob"](https://www.thingiverse.com/thing:4596787) style from [@scaryPug](https://www.thingiverse.com/scarypug/). ... It will not fit tight, it will be a bit lose, so put something...

This is a remix of Pieter86's Blind plate cover. ...This cover has a 10mm hole for the wire to pass through. This can be used with https://www.thingiverse.com/thing:5022603 when relocating the power switch on your Ender3_v2.

I am planning to make another LCD screen into the top cover, for OctoPrint. I have included the f3d design files so you can make changes and tweaks. Print Settings Printer Brand: Creality Printer: Ender 3 Rafts: No Supports: Yes Resolution: 0.2...

I've also included easy access to the SD Card slot on the rear of the unit. The case uses a centralised pair of mounting slots, so if you want to put this on the opposite side of the printer, just print the mount in reverse. The mount is adjustable...

The clip portion requires you to slow down for the extreme overhang.The stock fan shroud on the Ender 3V2 was causing this high-pitched sound, and it started to annoy me when the printer was idle. The screech is caused by how the fan shrouds are...

This will power on and off with the printer so your RPi will as well as anything you plug into the second USB port. I used this USB socket: https://www.amazon.com/gp/product/B08C7DFQT8/ This socket will take 9-32VDC input so it will connect right to...

https://www.thingiverse.com/thing:4735175 Did not fit on my Ender 3v2 machine because there was a metal plate on the "bottom" of the X stepper preventing a decent mount. I made the sleeves that grab the axis longer to make it fit. ... The pulley...

Remixed to fit spoolholder from Ender 3V2, should slide just over the know without the need of removing the spoolholder. Remixed from: https://www.thingiverse.com/thing:3975794 Using for the paper spools of "Real Filament" as the paper has a...

Cover for the Ender 3V2 Display. I recommend printing the frame in an upright position with supports enabled in order to make the snap fit work better. ... After assembling you can mount it with double sided tape to the screen as shown in the picture ...

I was tired of digging in the drawer for my Allen Wrenches... ...So, I made an Allen Wrench holder for the wrenches in the kit that comes with the Ender 3v2 Neo. ...Fit's on the top of the printer and is held in place by a T-Nut and a Cap Screw.

This is a Remix of the knob COVER for the X / Y axis belt tensioner on your Ender 3v2 and others using the same OEM blue knob. The original was WAY TO TIGHT, so I made this one. Its larger in every way! ...

Loved the original, but couldn't stand the little dimple in the d on the Ender logo. So I flattened it and embossed it. Also, mine was a wee-bit loose and would move when I took out my scraper. I added a peg that inserts into the extrusion to...

Printed in PLA , 0.8mm top, bottom and walls, with 10% Gyroid infill Remixed with Ender tool holder slide-in-rail clip , flipped over to print flat and resized to 110mm away from gantry. NB works well, but slide in clip could do with some resizing...

# Piezas requeridas Base: * [42] x Chain Clip * [42] x Chain Link * [01] x X_Axis_Tray * [01] x Y_Axis_Chain_Connector * [01] x YZ_Encap # Piezas Requeridas Especiales, según sea tu caso. ... ***En caso de que quieras poner el soporte del Eje Z sin...

I had to modify the mount for the fan duct to work with the fan that was on my V2. I don't know if the fans are different between the original and V2. This model has been designed for SLA printing, but should be fine FDM printing. There is no...

V2 Shroud has holes for an intake guard to hold the fan in place. Also fits the blower fan better with retention clips. There is a tolerance issue with the backing plate and the shroud. They will lock together half way sliding it together. I...

This is a v2 of a remix I made, which should hopefully solve the potential problems of space, bl-touch compatibility, and different mounting situations for the raspberry pi. The old design had the chain running forward, which increases the space the...

... in the wire. There is a 10mm hole for the wire to pass through. For those of you who do not want to drill a hole in your OEM cover. This can be used with https://www.thingiverse.com/thing:5022636 when relocating the power switch on your Ender3_v2.

A simple clip to keep the wiring harness from falling out of the holder on the back of the extruder bracket on the Ender 3v2. My wiring harness keeps coming out of the standard holder (see second image) while printing, so I created this clip that...

Reinforced webcam support after the original one is broken at base

... cables and the second one for the stepped motor cable of the x-axis. ...This base allows managing both cables separately. Dimensions and size are perfectly aligned to please the base in the base profiles. ...However, the design is under improvement

... Version 2: The Housing has now the same high as the original one, so it can used on the original setup. File: "Y Steppermotor housing v2.stl" I hope you enjoy this Make :-)

This is a remix of https://www.thingiverse.com/thing:5179838This remix takes the mount the fits the Ender3 V2 hotend shroud and modifies it to fit a Mitutoyo 2046 dial indicator. ...The mount is a direct replacement for the rear cover of the...

I made v2 smaller to reduce surface area that touches the X rail. It dragged a bit too much, so I saw that adjustment was necessary to update the JPG picture. The belt tensioner is designed to hold its shape over time and not deform. It slides under...