ender 3 v2 dimensions 3d models

Minimalist, simple and efficient with a very limited budget to be able to print almost any filament while keeping, at most, the original characteristics of the Ender 3 link of the video for the assembly with explanations and additional links:...

I've Successfully Enhanced My Ender 3 Nozzle Vent, and I'm Thrilled to Report That It Exceeds Expectations in the Bowl of Water Test. ...The Results Are Exceptionally Promising, and I Anticipate That This Upgrade Will Be Extremely Useful for Many...

i dont like the factory dial for the Ender 3 so i made this larger one with finger holes for faster/easier scrolling. this knob is 5/8' tall and 2.5" wide at the face. it is not press fit tight. ...it is able to slide off if you decide to remove it.

... to clip. ... My other fast printed Ender-3 parts: LCD Rear Frame https://www.thingiverse.com/thing:4659555 Spool Holder Slider https://www.thingiverse.com/thing:4695069 Tool Holder https://www.thingiverse.com/thing:4659697 P.S. ...Likes help to find.

... in a landscape position to for example stream the printing process.</p><p>Fits Huawei P9 Lite Mini. ...Should work with Ender 3 too. ...Hole for the tensioner bolt may need some adjustement depending on your setup.</p><p>Designed with tinkercad.</p>

A surface to attach your GoPro mount that you can slide through Ender 3's aluminum profile. ... To make a fast print for something for practical use only I used a 0.8 mm nozzle and printed it with a 0.2 mm layer height.

Took the Tool holder for the Ender 3 and merged it with the model for the flush cut pliers by jerome550 to create a holder for both tools. ... This is a remix from https://www.thingiverse.com/thing:398515 This is a remix from...

If you're using the Ender 3 Dual-Z Axis upgrade and have installed the Z screw retainers you can gain an extra 10mm by removing the extruder knob. ...I kept misplacing mine, so as I have the rest of my tools clipped around the printer it seemed a good...

I aim to rebrand my Ender 3 into an Iron Maiden themed printer. This is part #1. This thing replaces the original extruder knob. ... a very small support structure was used in the eye areas, but it's probably not needed.

I created this specifically to hold the UniTak3D Ender 3 3D Printer LED Lights found on Amazon here https://www.amazon.ca/dp/B0B7B1QG5Q?psc=1&ref=ppx_yo2ov_dt_b_product_details. I didn't like the way they just laid in the gantry rails so I made a...

LED mount for Creality Ender 3. No screw required. This is the LED light I used from Amazon. ... https://www.amazon.com/gp/product/B06Y3NWN8R/ref=ppx_yo_dt_b_asin_title_o09_s00?ie=UTF8&psc=1 Use slicer program to mirror part for left and right...

The holder has mounts for 40x40 mm rails like the ones on the Ender 3. Therefore no screws or similar are needed for the mounting. ... In addition, the holder is very material-saving to print and can be used flexibly because with two or more holders...

... near by and hadn't found anything I liked, so started learning how to use Fusion360 and designed this. ...It slides into the rails on the bottom of different Ender 3 models. ...I found it printed best from a corner, with a small raft and supports.

For ender 3 stock remix on https://www.thingiverse.com/thing:3091300 o-----------------------o Nozzle size ------------------ 0.4 mm Layer height ----------------- 0.2 mm Bottom/top layer height --- 0.6 - 0.8 mm Shell thickness -------------- 0.8 -...

Should fit the Ender 3 V2 using two screws and the included clip, however this has been designed for the Micro-Swiss hotend and may or may not cool or fit a stock Creality one properly. This duct is modular, and can be assembled using only one...

Filament spool holder for ender 3 v2, but I think it would work on other printers too. Note: I had the bolts, nuts, washers, and bearings lying around. The bearing I used were 'bad' (for their previous purpose in a table saw motor) but they are...

Remixed to engrave the Ender logo @ .8mm depth Print Settings Printer Brand: Creality Printer: Ender 3Rafts: No Supports: YesResolution: .16 Infill: 15 Filament: 3D Fillies PLA+ Black Category: 3D Printer Accessories

(:Since I am no good at explaining thingies I added some photos.I am no expert on electronics, so I don't want to add a "how to connect the cable to the 24v ender 3 power supply and ruin your printer" section.I just connect the + - cables to the...

This is a small cover that helps keep cables inside the aluminum extrusions on an ender 3 to help give a nice and tidy look. I fit a 3.5 mm cable with the clip over it, I'm not sure how much bigger you can go. Printed with PLA. It just slides in from...

UPDATE: to get updated files go to my thingiverse: https://www.thingiverse.com/thing:4812842 This is my Front Electronics Enclosure for my Ender 3 V2. If you're like me then you get really tired of having to flip your printer over onto its side every...

Screw template for standard hotend bracket for Ender3 V2.

this is mount works for the ender3 v2

Remixed to engrave the Ender logo @ .8mm depth

Remix of mplantain's original file w/ ender logo

This is another case for the DACAI and DWIN display of the Ender-3v2 and Ender-3S1.

Fitted thus far to an Ender 3 V2. Planning to print another for the 2 Ender 3's I have as well. Printing upside down can avoid the need of supports but depending on bed may not give you the cleanest finish on the top. Printing right side up...

Hi, Dual Z bracket/mount for Ender 3 / Ender 3 Pro, (for use with anti backlash nut, mounted at the bottom) no need for extra hardware. ...The screw mounting hole is at exactly same level/height as original one on the other side ;-) enjoy Print: ...

I loved the original concept by mlynch002, but I felt it required additional bolts securing it to the main frame of the Ender 3. Noticing some gaps in Cura, I reinforced the design and ensured all sections were fully connected. This updated piece has...

Made for the Creality Ender 3 v2, but it may fit the Creality Ender 3 and other Creality printers. This is an x-axis carriage mount that works by attaching a digital depth gauge (like [this one found on...

The latest revision of my CAIMEO Fan Duct for the Ender 3 is now live. This upgrade takes a significant leap forward with several key improvements over its predecessor. The most notable change is the relocation of the fan to the rear, allowing for...