ender 3 v2 octopi 3d models

This is a TinkerCAD remix for use on Ender3 V2to reduce noise and maximize air flow:bigger intake fan opening with chamfered edgestill no fan guard (not a good choice, if you have pets or young children)more exhaust side portsrelocated mounting holes...

Just a tweak to adapt for the Creality Ender V2 PSU mounting for the rear legs. Print two of the original 4124150 that this was remixed from and two of these. ... Enjoy!

External Power supply support for Ender 3 V2 + cover. You'll need to cut the original PSU cover to fit a 92x92 mm fan. You'll also need to do some rewiring. It's not really hard but it can be dangerous ! It's a Power supply !! Also check the voltage...

I made these to help a friend with rheumatoid arthritis that a tough time reaching and rotating the bed leveling nuts on their Ender 3 V2. Simple: put the tool's pegs in the holes of the appropriate leveling nut so you can adjust it easier, but...

It can be used to cut out small stickers on your Ender 3 V2 print bed, essentially turning it into a vinyl plotter. Has two hooks on the left side for slightly varying pressure of the rubber band which holds tension on the plotter blade. Things...

I made these to help a friend with rheumatoid arthritis that a tough time reaching and rotating the bed leveling nuts on their Ender 3 V2. Simple: put the tool's pegs in the holes of the appropriate leveling nut so you can adjust it easier, but...

The design is ONLY compatible with the above parts referenced above. Print Settings Printer: ender 3 v2 Rafts: NoSupports: No Resolution: .20Infill: 15% Filament: creality PLA white Notes: 45mms speed; .20 layer; no z hop; 3mm brim. ...temp...

This is a remix of micahjj's and ryroo211's Filament Runout Sensor mounts designed to allow you to reuse z endstop switch as a runout sensor on Ender 3 v2's that have been upgraded with a BLTouch/CRtouch. I added some screw holes to the sides of the...

I printed this for my Ender 3 V2, but it should work on the Ender 3, Pro, V2. This is a remix of the chain end made by DIOGOSANTO88. I remade the end that the chain connects to on the extruder end. It combines a place to attach the chain along...

The Ender 3 v2 Left Side Screen Mount was designed to print easily (as oriented) without supports, though you will need to remove a sacrificial layer from the four screw holes in the Back Plate. You will also need two M5 by 8mm bolts and two M5 nuts...

I have an Ender 3 V2 and used the 45° spool holder by @ZTolerance (https://www.thingiverse.com/thing:3446507). Didn't read the description properly and just mounted it with the screw that was already in the frame (for the Ender 3 V2 at least this is...

https://www.thingiverse.com/thing:5236927** The stepper motors on the Creality Ender 3 v2 3D printer are very quiet, which makes the cooling fans the loudest parts of the machine. If the user replaces the included fans with quieter alternatives, the...

Ender 3 v2/3D Printer Desk Tidy ## by DAR01. Made just for the fun of it. This is a simplified model [loosely] based on an Ender 3 v2 to be used as a desktop organiser or tool caddy for the true 3D printing fanboi! Can be scaled as required in...

**************************************************************************************************************** This is a side-mounted spool holder with a bearing roll for the Creality Ender 3 V2. Inspired by...

Fits well with the following mods: Motherboard cover: https://www.thingiverse.com/thing:4653994 Ender 3 v2 PSU cover + cables cover (80mm fan): https://www.thingiverse.com/thing:5778820 Ender 3/pro/v2 Riser feet 45mm:...

While making my first prints on the Ender-3 V2 the cable that runs to the nozzle got stuck between the print bed and the motor that is situated in the rear of the printer. To prevent this from happening I designed this cable holder. To attach the...

Fits well with the following mods: Motherboard cover: https://www.thingiverse.com/thing:4653994 Ender 3 v2 PSU cover + cables cover (80mm fan): https://www.thingiverse.com/thing:5778820 Ender 3 v2 Front Power Switch Mod:...

You can also raise the camera itself -after mounting it- for your liking.Print SettingsCreality Ender 3 V2 Neo - using Cura + Filament Friday Extra Fast 0.28 profile with 10% infill. Important: Print with a brim to help with adhesion. ...No support...

Original print was too tight for my Ender 3 V2 (i wanted the strips to be slightly above the bed), so i I adapted the inserts by shaving off 0.2mm on either side of the grip face, changed the lengths for my setup, and trimmed the edges to better...

As it means when you take your spool off of the holder, the spool holder will retain the adapter * This means you can print one holder to stay on the printer, and one for each spool which should stick to the spool * On my Ender 3 V2, a 101% lets the...

Please make sure you have enough clearance before printing. Print Settings Printer Brand: Creality Printer: Ender 3 Pro Rafts: No Supports: Yes Resolution: 0.2 Infill: 20 Filament: 3DJake ecoPLA Black Notes: If you are printing on a Ender 3 V2...

#Ender 3 v2 compatible direct drive extruder mount Based on the CR-10 / Ender 3 Direct Drivinator by Madau3D ----------------------------------------------------------------------------------- I printed the version without a logo that was remixed by...

... Later on v1.1 will include the Screws with a head, scaled to the tool you get for Ender 3 v2 pack-included, and Screw "1" optimised, so that you dont need to get two screws out when you remove your phone, and i plan adding a Smaller Connector part.

Use this model if you have problems with aligning the lead screw. https://www.printables.com/model/635002-ender-3-dual-z-axis-upgrade/ This is a bundled STL package to upgrade your Ender 3/Ender 3 Pro/Ender 3 V2 printer to use dual z-axis. All the...

Just remove the corner cap, slide it on, and replace the cap. PRINT ORIENTATION is best on it's side like shown in my 2nd pic PLEASE NOTE only tested to work on my Ender 3 V2 as it has taller feet. ...If your Ender 3 or Ender 3 Pro are stock, this might...

I also ended up meshing the rail mount with that of a modified "[Ender 3/v2 Feet Riser 20mm](https://www.thingiverse.com/thing:4926407)" by MythicalThings to create an incredibly tight fitting rail insert. The included file(s) are easily extensible...

I wanted to upgrade my hotend on the Ender 3 v2 to give some additional capacity for printing larger, draft quality prints at an accelerated speed. After doing some looking around the Phaetus/Triangle Labs Dragon, Slice Mosquito, and e3d V6 were the...

Improved Filament motion sensor for Ender 3 V2. Not only detects a filament runout, it also detects a nozzle clog and pauses the print safely. Intended for use with klipper. ... ##Used Parts [M3 20mm...

This is a remix of the Ender 3 v2 X-Axis Camera mount. I've extended the arm by almost 14.5cm and added an end piece that is 6.77cm long that you can use to better angle the camera.Best to print it laying flat with at least 3 walls. I printed 15%...

Ender 3 V2 Printer 2. BlTouch 3. Direct drive plate from Amazo n ( Link below ) 4. Noctua fans for cooling. I tried many builds but then I had to make my own to fit all my needs I bought the direct drive plate from Amazon. ... ...