ender 3 v2 vs ender 3 s1 pro 3d models

A replacement y-axis stepper mount for the Ender 3 S1 Pro. Tested on my machine which has a gulf coast robotics y-axis rail kit but this is as close as a 1:1 copy of the stock mount as I could get in terms of critical dimensions. It uses the stock...

Installation ===== * loose the right corner screws in the base of Ender 3 S1 pro, push the my mount print into and then put screws back * after that the pi case can be installed to the left with the dove tail joint * cam holder is easy as seen in...

Unfortunately I couldn't find a spool holder with load cell that fits to the holder of my 3D printer (Ender 3 S1 Pro). I don't know if this design also works on other printers.I use a HX711 with 12,7x12,7x75 mm load cell (i use the 10kg load cell but...

Route filament from dry boxes to the Creality Ender 3 S1 Pro printer using this [Bowden tube guide](https://www.youtube.com/shorts/nfN7RhlbYGk). The assembly consists of a main control arm, a pulley hook, fitting plate, and snap locks to maintain the...

Made a quick holder to attach a small thermometer/hygrometer to the top rail of a Creality Ender 3 S1 Pro. It holds [these thermo/hygrometers from Amazon.](https://www.amazon.com/gp/product/B07GR65CNT). (Incidentally, these things have been working...

The Ender 3 S1 Pro has a big plastic base that covers up a lot of places where the switch for the 3D Chameleon color changing system could be mounted. I decided to go simple and mount the switch right on the plastic base using 3M Command Strips. So I...

A simple but effective webcam mount designed specifically for the Ender-3 S1. Simply slides on to the X gantry, no tools or disassembly required. V2 changes: added cable tie holes. Also included is a threaded knob to match any webcam with a...

... ...Now thicker base sround the Dial stem, And can secure Dialindicator with a 3mm screw. Clips on over heatblock fan cover, should be removed after use as it covers part of the fan intake.Printed in PLA+ 20% infill on a Ender 3 S1 Pro

Remixed this from an Ender 3 Pro LED Light bar holder by scottyujan. I just found it to be too short for the LED light bar I had kicking around. Extended the ends to support my 30CM bar. ...Tucks neatly under the S1 filament runout sensor.

Ender 3 S1 Extruder Arrow, Print in a bright/different colour to black so its easy seen.I printed 0.2 layer height with Cura 5, added a chamfer to help push it on. ...Its quite a snug/tight fit but I have tried it on both my Ender 3 S1 printers and...

I liked the aftermarket Z-axis stabilizer by p1mrx, but the front mounts didn't fit my Ender-3 S1 Pro, and the rear mounts were too unstable. I redesigned the mounts to fit my frame (which appears different from the one the designer has), and added...

Sadly the original model doesn't fit with the ender s1 pro, so i made a little remix. There is a hole at the lower end, you can stick a little piece of filament trough, fixing the cable in place. I recommend printing with 100% Infill, the clips...

Recipients of this instruction assume all risks associated with its implementation and release me from any responsibility for consequences thereof.Part ListPrinted Parts1x Creality Ender 3 S1 Pro Drawer1x Camera Case1x Cable Cover1x Camera...

Since my Ender 3 s1 pro has a filament spool rack with bearings in it i made this end-cap and spool spacer set to allow the spool to use the bearings instead of freely spin. You will need 2 spacers and 1 end-cap, Edit: complete re-write of...

(At least on the Ender 3 V2 with the Sprite Pro extruder) You would then set the endstop position to keep the nozzle zero above the build plate. The fit is good, you will need slightly longer M3 screws than the ones originally used to mount the...

3 sides cooling for ender 3 S1. You can use the original fan Sorry, I forgot to mention that: I printed it with 0.2mm, support only on the printing plate. ...(E: 195°C | B: 60°C | Speed: 45mm/s)

A remix of AJCam44's excellent cable support for Ender 3 S1 Pro. I adapted it to fit the S1 non pro. Also I added support for extra wiring shown in the photos. Should work with PLA but I used PETG. The bottom support bracket is very different...

This is a webcam mount, to use a Logitech C270 on an Ender 3 S1. If you are using a Sonic Pad, and have removed (or want to) the original control pad, this will make great use of the screw holes. Since it is hard mounted on the corner of the machine,...

This is an "inverted Bowden" adapter for the Ender 3 S1 Pro. Yeah, I know: what the F is an inverted bowden? So, basically, on a direct drive extruder system, you have a bowden tube running from the spool holder to the inlet of the extruder. This...

A Wyze cam mount for my Ender 3 Pro with a handle and more sturdy holding.

piastra per bmg in direct per ender 3 pro o 3v2 con bullseye o stok

This bracket has been designed to replace the stock bracket that comes with the Ender 3 S1, it comprises of three prints. The main bracket that screws in to the same holes as the stock bracket with the stock screws. There is also the lid which is for...

This is a camera mount for the NeXigo N960E 1080p webcam, which works on the Ender S1 line of Creality printers. There are two mounting styles, one mounts to the top of the x-axis tensioner and the other secures from the side of the x-axis tensioner....

This is a tool Tray for the Ender 3 S1 drawer. ...Includes individual compartments for each tool type, USB thumb drive, and a compartment with a sloped ramp to hold the SD card.

Es Handelt sich hier um einen Kamerahalter für den rechte Seite der Z Achse des Ender 3 s1 Plus. ... die Kamera wird von unten mittels einer m6 Schraube angeschraubt

This is a tool keeper tray for the Ender 3 S1. Slides into the existing drawer for a tight fit. ... I left some front-to-back spacing to allow for removal when needed.

Cover for the Ender 3 S1 LCD Screen. Keeps dust off and protects against scratches, or Loki's anger. ... https://www.prusaprinters.org/social/223023-three-nippled-goldfish/prints

I have customised the model https://www.thingiverse.com/thing:5264357 to fit better with generic ender 3 S1 accessories / clipper and scraper. ... This is just raw edit made in IdeaMaker with boolean feature, but works just fine.

This is a remix of the mount for HugoHuge's "filler" filament roller. ...I made it to fit the stock spool holder arm for the Ender 3 S1. ...I printed it at 30% infill with tree supports.

This is cable chain for Ender 3 s1 3D printer. You are need print 15 chain link and glue the two parts of the top. ... The bottom is attached to the profile, the top is attached to the roller bolt.