ender 3 y linear rail 3d models

This is a modification of the 90 Degree adapter for the extruder cable to allow the adapter to be fitted to a linear rail conversion.The through holes in the adapter have been sized to allow the screw head through for easier install. This is ONLY the...

This is a rail filament clip, i tested it and clip work very well! ... U can adjust how much long clip is if u want

Needed a top rail filament guide, allowing me to print as highh as possible w my direct drive/filament sensor printhead.

Print this part on its side with standard supports for best results. ...Don't lose your 20mm rail caps next time! ...Happy printing

I have made this remix becouse when i installed Hero Me Gen 5 fan duct i needed to move my Y axis end stop about 9 mm. Becouse of that, there was a risk of crashing the table mount plate with the tencioner body. My remix fixes that problem and...

... ...You will probably need to shave down a little bit of the + signs to get an accurate fit. I tried using this to support an accessory like a webcam but it was not enough support. See my other design where an internal rail is used for added support.

The original is really neat, but I don't have the nuts on hand to mount it to the printer, so I stuck a rail on that part. ...The rest of the parts from the original work great, use that.

I adored the original rail cover, but it was a must that I had one emblazoned with Yoda's iconic visage. ...As such, this rendition is based on the more robust v2 model design.

I designed this to keep my Raspberry Pi 4 case tucked out of the way while providing ventilation for the case fan. ...Simply hangs on the lower rails on either side.

Nozzle Holder Assembly for Upper Rail, Easy Printing Made Possible by Separate Parts. Glue Together for a Secure Fit. Print Magazine at 0.1 Layer Height for a Spotless Finish. ...Additional Version Available with Customizable Number Colors.

Little tool holder for the top right corner of your ender. Based on others I've seen on here so not my original idea. ...It fits tight FYI so you don't have to worry about it slipping off.

This is a little top rail mount for an ID badge holder/reel. ...The idea is that you can use the id badge reel to hold up your cables and bowden tube to assist with sagging. Supports-NOMaterial- about 5g or 160mm

This is a little top rail mount for an ID badge holder/reel. ...The idea is that you can use the id badge reel to hold up your cables and bowden tube to assist with sagging. Supports-NOMaterial- about 5g or 160mm

... provided. ...It's nestled snugly behind my Raspberry Pi box, with everything fitting together seamlessly without requiring any additional mounting hardware. I simply slid it into the rail situated directly below the "Z" motor, securing it in place.

A straightforward rail that easily inserts into a frame, holding up an already established chain configuration. Two compact supports slide under the standard cable chain top mount. To see the original chain setup in action, visit...

... cam needed a new mount platform. ... Using the measurements from PsychProd's mount + the end piece on the rail this remix was born. ... About to extend this and add a 200mm straight piece to potentially give a better advantage for OctoLapse captures.

... in its upright orientation. This resulted in one side that attaches to the rail being slightly longer than the other. Additionally, this approach minimizes the number of supports required. ...To make removal easier, I set the support density to 10%.

... 12v to power the on/off toggle as well as the 12v LED lights. ...I have other accessories so I had to adjust the mount length for the rail to accomodate, but if you find one leg is too long for your application you can just snip it with your trimmers.

**Step 2: Slide the Part Forward** Slide the part forward until the lip on the top pops down the front of the rail and stays securely in place. ... If You Like the T-Slot Covers in the Photo, Check Out My Design at...

... in a couple utilities and looks great. Any credit should go only for both designers. I just printed them together. You should print it as is using supports. You can check other recommendations from the rail cover designer. ...

This is designed to be used with direct drive. I am using a Biqu H2 extruder but it will work with others obviously. You must print at 100% infill. I used 0.2 layer height. This set up eliminates the need to recenter the build volume after...

This is an upgrade to the original Tevo Flash Linear Rail Mod. The Y axis printed parts are now significantly more rigid and durable, while the Y axis tension is now fully adjustable through screws. ...To implement this update, you'll need to add a...

# CR-6 SE Y-axis Linear rail and MGN12H carriage mount THIS PROJECT IS UNDER DEVELOPMENT This conversion method DOES require you to replace the Y-axis belt, but unlike some other projects doesn't require you to cut the rail. Required Supplies: - 2x...

cordialement ------------------------------ Bonjour, Il s'agit du montage de rails Linéaires sur une Hypercube. Cette transformation permet d'installer les têtes d'impressions du projet EVA. ...(Extruder : LGX, BMG, Orbiter, Titan, Hemera, Aéro,...

Original Part ----------------- This is my take on a Y-axis linear rail conversion for the Creality CR-10 V2 and V3. It allows for mounting the bed plate to two parallel MGN12H linear rails with two blocks per rail. Unlike many designs, this does...

This is a simple method for assembling a piezo disk for use with the Precision Piezo Z-Probe and printingSome 3 Wheeled Carriage for the D-Bot corexy printer. The idea behind this assembly comes from DjDemonD's motor mount for titan extruders, so...

Center holes are spaced out to match the original Y carriage, and the linear rail holes are spaced far enough apart to avoid the Y stepper. If using as a jig, then simply print at a few mm height. If using as a base, then use 10-12 mm long M3...

CR-6 SE Y-axis Linear rail and MGN12H carriage mount This conversion method DOES require you to replace the Y-axis belt, but unlike some other projects doesn't require you to cut the rail.Required Supplies:2x 350mm long MGN rail with MGN12H...

This is a complete package of printed parts required for upgrading the Y axis on Anet A2/+ with MGN15 linear rail. The belt tensioner part was remixed from Olev's design (https://www.thingiverse.com/thing:2157807) to incorporate a parallel belt when...

Remix to allow using mounts with the 4DM bed extension. ... You will need 300mm linear rails (instead of 200mm), no need for cutting. ...Fit is snug.