ender 3v2 fan upgrade 3d models

Ender 3V2 Direct drive cable guide placed where the extruder motor used to be 31mm by 31mm radius bolts for those that have Unitak DD configuration, and have modified other bits, I needed all the wires fed and held in a certain position so this ive...

Here is a indicator-style boss added on to an Ender 3V2 extruder cover, enabling easy attachment of a Dial Indicator to the extruder housing. Also included is an STL file with a couple mounting brackets that allow mounting in different...

The side mount for the spoolholder found on https://www.thingiverse.com/thing:3274902 was too short for my ender 3v2 to keep it free from the Z-axis stepper motor. So I adjusted this mount. 3 alterations: - I extended the middle section so now it...

Here is a indicator-style boss added on to an Ender 3V2 extruder cover, enabling easy attachment of a Dial Indicator to the extruder housing. Also included is an STL file with a couple mounting brackets that allow mounting in different orientations....

Remix removed text from face of the cover and worked on fitment/contour to match Ender 3v2. 1. (MicroSD Cover with Angle - Full Panel.stl) Added a nice angle to allow for easy removal. (This one is my favorite). I added some extra support...

This is a filament guide for the Ender 3 V2 with the upgrades First Layer dual gear extruder. The other models I found were not tall enough and did not left the filament spool freely. Also, it has a cable hook since this extruder takes that away.

Ender 3V2 Unitak Direct Drive wire guide No amount of zip ties and trying have I ever managed to get all the wires in a place that didnt either catch on the frame when calibrating before a print or when bed levelling, or if i did it looked an eye...

It secures to the frame using the two screws in the front of the ender 3v2 extrusion on the left side so needs no extra hardware. The fitting for the screen to clip on to it is deliberately tight. You will have to sand a little off for easy fitting...

Version 2 available: Ender 3V2 Damper Feet (Soft Springs) von AaronLK As far as I can remember my engingeering-courses the machine should sit on springs as soft as possible to reduce vebrations from/to the environment. Standing on a IKEA Lack table...

This combines a bed handle with the bed level knob locks. Bed Locks are labeled for easier install... LF = Left Front RF = Right Front LR = Left Rear RR = Right Rear Tested on Ender 3v2 but might work for Ender3/3Pro and possibly CR series. If you...

Remix removed text from face of the cover and worked on fitment/contour to match Ender 3v2. (MicroSD Cover with Angle - Full Panel.stl) Added a nice angle to allow for easy removal. (This one is my favorite). I added some extra support inside at...

... frame or stick in on the fan afterwards. Link to TinkerCad to change it up for your application. https://www.tinkercad.com/things/6MrvzGefMlj-remixed-all-in-one-undercarriage-ender-3-v2/edit A nice touch was the Pi3 LEDs shone through the PLA.

Niggled me constantly after that, consequently I designed and printed this small cover for the Z plug.  The ender 3v2 z stop connector comes out of the top of the circuit board enclosure and looked like way too much messing about to delete for little...

There are a lot of suggestions how to reduce noice of the Ender 3 fans. I was inspiried by Cbarth3 (https://www.thingiverse.com/thing:4568512). He cut out the "covers" above the fans. So did I :-) but I wanted to keep the original panel sheet of the...

This is a remix of my previous design for the Voxelab Aquila, designed instead for the Ender 3v2, which I also have. I wanted a very clean and compact design that held the ultra cheap runout sensor I purchased and guided the filament with a...

Made for my Ender 3 V2, should work perfectly on Ender 3 / 3 Pro except the extra hole will not be correctly aligned with the hole in the gantry plate. Currently used with a Satsana remix duct with a 5015 fan. Might replace with something even more...

A quick camera mount I made for my Ender 3v2. I am biased, but I think this is a really great solution for mounting pi cameras on this printer, and I was a little surprised nobody seems to have made one before. It is very secure, offers a good...

The ender 3 V2 hot end assembly attaches with one screw in the back, instead of two in the front on the ender 3 and ender 3 pro. ...I made a small change in this part to go around the screw on the ender 3 V2.

Scaled down the knife to fit a ender 3 v2's print bed.

Scaled down the knife to fit a ender 3 v2's print bed. Category: Other

What i used: Slicer: Cura Infill: 20% Support: No Adhesion: No Material: Basic Pla Printer: Ender 3 V2 Neo

Upgrade to atach the wireless button to the printer and make some amazing timelapses atach it on the Y axe from bottom button added with zip tie

This is a remake of thing:4594025. ... It includes slots to see the time on the Ender 3 v2 Screen. ...Thanks to the Original Designer for the design

Remixed version of the RODAM Ender 3 spool holder, which was made by Rodamyot. ... This version can handle some larger spools.

Y-tensioner (for ender 3, V2,PRO) modified for installation of a direct drive (see my YT chain with direct drive links). ... Modified by SIX SAUER ;-)

... to the nozzle. The Bowden tube is shortened to 63mm. You will need to extend the wiring to the extruder motor. Parts: 4020 fan (screws for fan), 5015 blower fan (screw for fan), 1xM3 8mm screw to attach fan duct to the direct drive bracket

I remixed this design with an extra height of about 4m to give the Notcua 80x25mm fan better fitting room. ...I also removed the buck converter mount because it is not needed with the Noctua fan.

I combined 2 models to create this extruder knob topper for the ender 3 v2 https://www.thingiverse.com/thing:4736138 Ender-3 v2 Extruder Knob Overlay by edk_sc January 24, 2021 https://www.thingiverse.com/thing:2033990 stackable fallout vault door...

Since the filament holder faces the bed, I edited the Ender 3 holder from https://www.thingiverse.com/thing:3209211, by https://www.thingiverse.com/mjoaris. This will hold all 1kg filaments no problem. This is almost the same size as the stock...

i maid a base for the stock ender 3 spool holder so it's sepret from the printer it has no problen holding more then 1 kilo of filament to assemble you need two m3 screws