ender 5 plus dimensions 3d models

Quick print. ...Created this because tube would get stuck there from them to time...

This object was made in Tinkercad. ...Edit it online https://www.tinkercad.com/things/iSsNFFmStZB

I needed a taller version to prevent my cables from hitting the homing sensors. ... Feel free to make changes.

Removed Creality Logo

These models were draw up by another user I just modified. Front plate added a little more material to screw board in. Also change to 3-4 perimeters in screw areas where back plate screws to front gives more strength for tapping 3mm holes. Back plate...

This adaptor fits between the Microswiss and the Bigtree tech runout sensor

This ergonomic accessory lowers the sensor by 40 millimeters, making it simpler to load and unload rolls without straining. It's particularly handy towards the end of a roll, where minimal grip is available. ...Installation requires standard hardware.

<p>Very quick and easy bed leveling test. ...The squares are 20mm each placed on every corner and middle of the bed.&nbsp;</p>

Yet another set of standoffs. I made this version because I did not have a right-angle USB-B cable and I did not want to drill in the case. This moves the board flush with the heater control MOSFET and leaves margin on the side for USB cable. ... ...

This is a modification of the original publishers design made in Orca Slicer by simply adding positive and negative components. It allows the 2 build plate locators to be placed under the bed adjustment knobs to hold them in position. It also...

The Skin V1 is a single piece that demands: Two M4x10 screws Two Tnuts M4 Four M3x20 screws Four M3 nuts One M4x20 screw One M4 nut The Skin V2 consists of two parts and requires: Two M4x10 screws Two Tnuts M4 Four M3x20 screws Two brass inserts...

I don't have the hardware right now so I thought I could make a version that didn't need it. ...I have not printed this yet but please tell me if it needs to be fixed.

This a remix of Kersey's remix, the board is moved 10mm back towards the PSU. This is to reduce the stretch and stress on some of the wiring that is a bit of a reach. ...The two blocks are to be glued on to the underside of the mount on the PSU side to...

Improved version of original, removed gap that caused the ears to break easily, added chamfers and bevels to add strength, fixed some spacing issues and other small errors Screws still needed from original print

This is a remix that has a recess to move the screen closer to the outside face of the stock electronics case. There's also cut outs for the SD card and USB ports to make them usable with the screen mounted, though you will have to open the case to...

I was going to make Gnizten's model when I saw that they already did it! Thanks! However, I try to print support free, and his model was on an angle which is an issue for some. I adjusted the angle, removed the lip to make the front flat, and put...

I used this design for my linear rail conversion, I'd used others but this one I felt had better Y brackets and the X cartridge bracket was great. The bit that I liked the most was the ability for you to print the X gantry without supports, the...

Drill and tap the Y bearing bracket using the mount as a template. can be mounted on any side of the Y axle. 4x M3 brass inserts 6x M3x8 screws S42B Servo can only be used on motherboards with removable drivers. ...ex: SKR 1.4 , GTR, ,etc,etc,, ...

Remix of https://www.thingiverse.com/thing:4903022 I have a v2 biqu h2 with full metal heatbreak and it looks like the nozzle is a bit higher then the original design is for. I changed the screw holes to be adjustable for the biqu so you can shift...

Right up front, I apologize - THIS IS A REMIX. Since Thingiverse REMOVED the ability to download all files that included identifying data on the thing you were downloading I could'nt find the original Thing number. That being said - if you designed...

Disclaimer: I am not at all good at 3d modeling. I used Tinkercad to splice this up with some other mounting plate. ...Haven't tested/mounted it yet but it printed fine

The bolts on the bottom of the gantry mounting plate hit the middle of the bracket so i used tinkercad to hollow out a channel

Quick and dirty update to the cable chain tray for the X axis. Allows the trays to be used without the need to relocate the Y endstop. ...This replaces the right-hand (from front of printer) piece of the X axis tray.

This routes the hot exhaust from the mean well power supply out the side of the case instead of across the mainboard. ... Print with support touching the build plate.

The standard X-axis limit switch placement isn't exactly rock-solid. ...This mounting bracket adjusts the switch's position, ensuring a stable connection with the print head carriage instead.

This bracket provides a direct drop-in replacement for the stock Creality mount, accommodating the BMG extruder and filament sensor seamlessly. However, initial attempts to install the BMG extruder revealed that the filament path didn't align...

This is a remix of thing 3591391 that adds the ability to zip tie the cable loom and Y adapter of the 3D Chameleon to the hotend strain relief preventing any bending of the short tube that goes into the hotend as well as adds cable support along the...

RPi Cam holder/mount. It is forward facing and rear mounted above the spool location. Swivels left and right and pivets up and down. 2/M5x10mm buttonheads bolts with T nuts and 1/M3x40mm bolts for pivet. ... Works for me.

Two side mount and the spacer/washer for mount to the frame print 4x of it

This is a remix of the original: https://www.tinkercad.com/things/0MDHjpUZp1y The original design works well, but wanted to add some more rigidity and support. Added in two bolt holes that fit a M4x20 button head cap screw to be paired with M4...