ender 5 plus linear rails 3d models

Ender 5 PLUS One 400mm top one 400mm bottom rails with two MGN9C carriages. Tool included to line up rail. If you buy the cheap ones make sure you inspect and clean your carriages before installing, info available online from many sources. ... Y limit...

Ender 5, Ender 5pro, Ender 5plus and possibly the Ender 3. Only fits the Stock hot end plates. Slips on tight no screws or disassembly required for this simple mod. Settings if using a Micro Swiss hot end and hardened steel nozzle Most settings...

The goal was use a Bondtech LGX extruder in a direct drive configuration with the Ender 7 Style dual 4010 fan shroud all mounted to a printermods MDD v1.3 plate with linear rail conversion. I am not an expert at 3D modeling so some filing and...

You should always wash new linear rails to remove any anti-rust or dried grease on the rails. Fits 150mm MGN7 rails typically fitted to Voron 0.1 3D printers. Put rail in the bath, add IPA, then slide the carriage back and forth 10 times. It's...

The mount on my Ender 5 w/ a Mosquito Magnum, MDD 1.3, and linear rails was not stable enough. I was getting some bouncing. I could not use a gantry clip because the rails were in the way. I added one more mount point that uses the screw that...

Designed for seamless integration with the FolgerTech FT-5, this part is also compatible with similar setups featuring linear rails attached to T-slot extrusions. The hole is precision-engineered to accommodate a 10mm M5 pan head screw and an M5...

Uploaded BMG mount for standard V6 to account for the BLTouch Recreated in fusion for my Ender 5 Plus, as Creality has slightly modified their hotend carriage. It should fit the other Ender 5, Ender 3 and CR10 series as well as they all have...

... the frame. My extra light cooling shroud for ender 5: https://www.thingiverse.com/thing:6079627 My BMG direct drive mount: https://www.thingiverse.com/thing:6079570 Design inspired by the original Satsana: https://www.thingiverse.com/thing:4528533

I've spent considerable time working on a mount for the OmniaDrop for the Ender 5 with linear rails and an EZABL. This is my twentieth version, which I'm naming OMNIADROP V1. It's now ready for publication. I used plugs on all of the wiring to...

... plate. Attn: Use a crew that is not too long otherwise it will touch the frame. Link to my direct drive mount for BMG: https://www.thingiverse.com/thing:6079570 Link to my dual 5015 fan duct for ender 5s: https://www.thingiverse.com/thing:6079533

I redesigned [this](https://www.thingiverse.com/thing:4810011) linear rail setup to accept an orbiter 1.5 extruder because I didn't like the rail on the back. ...Now it doesn't have to fight gravity!

This modification is designed specifically for the mk2 full bear frame, adding MGN12C linear rails to the Y-axis. The files provided are printed parts needed to set the bed at its correct height. Note that you will require 6 low-profile countersunk...

Ender 5 Pro Linear Rail, Direct Drive & Dual Z Mod Ich habe die 2 Stück 2020 Profile entfernt worauf die Zachse befestigt war, eine zweite Z achse angebracht möglichst Baugleich zu dem Original. Das Bett wurde 1cm erhöht damit das Hotend nicht gegen...

As I wasn't completely satisfied with the existing Y-axis rods, I decided to switch over to MGN15(C) linear rails. This upgrade should be compatible with all Bear upgrade printers but I've only tested it on my MK3S and now I'm really happy. This...

Is a mount for bltouch and nf sunrise 1.2 extruder in ender 5 with top linear guide mod. It is mobile, you can adjust the bltouch heigh for volcano o another block. ... For more stability use 3 insert m3 and 3 screw (2 for fix mount and one for fix...

This is a mounting plate I designed to fit onto an MGN12H linear rail carriage for the Creality Ender 3 x axis. I seated my linear rail right next to the limit switch so that the carriage activates the switch without falling off or exposing any ball...

This is a mounting plate I designed to fit onto an MGN12H linear rail carriage for the Creality Ender 3 x axis. I seated my linear rail right next to the limit switch so that the carriage activates the switch without falling off or exposing any ball...

Heat-set inserts are highly recommended for several reasons. ...They excel at clearing the Z-axis linear rods, especially when working with MGN9 linear rails on the Y-axis.

I built an enclosure around my Ender 5 Plus. After do that I placed my Spools in a Zip Lock container (with Filament drier inside) on top of the case. Then, I just routed the filament from the Container through the top of the Case with Capricorn...

This is my slowly and gradualy desgined cable chain for my beloved Ender 5 with Micro Swiss Direct Drive. It is a remix of very sturdy chain for Ender 3 by Diogo Santos https://www.thingiverse.com/thing:3715002 and some Nema17 motor chain mount I...

This is my slowly and gradualy desgined cable chain for my beloved Ender 5 with Micro Swiss Direct Drive. It is a remix of very sturdy chain for Ender 3 by Diogo Santos https://www.thingiverse.com/thing:3715002 and some Nema17 motor chain mount I...

This is my slowly and gradualy desgined cable chain for my beloved Ender 5 with Micro Swiss Direct Drive.thIt is a remix of very sturdy chain for Ender 3 by Diogo Santos https://www.thingiverse.com/thing:3715002and some Nema17 motor chain mount I...

It is an adapter for Duet into Ender 5 PLUS.

Ender 5 Plus Heated bed cabel holder. ... Support: No

It is an adapter for Duet into Ender 5 PLUS.

For mount Duet Wifi board to Ender 5 Plus.

My Ender 3 uses a X axis linear rail and the SpeedDrive direct drive conversion with BMG extruder. I removed the top of the cable tower because it interferes with the use of my Speedrive BMG mount. I also put 4 holes in the mounting plate for my...

This fan shroud is designed to specifically fit an Ender 5 Plus with Spider Hot End using the HBE X Carriage (purchase on eBay). It allows the reuse of the factory fans and BL Touch mount while providing clearance to the linear rail mounts. This...

Ender 6 linear rail mod MGN12 it is not necessary to disassemble much screw change required 2x M4x-40-50 4x M3x8-10 the part has been tested and works perfectly i use 350mm length but can also 400mm if you cut or remove the blue decorative parts

Experience the excellence of 440C SUS high quality linear rails, available at RobotDigg (http://www.robotdigg.com/category/20). These linear rails ensure smooth and precise motion for your automation needs. ...Check them out now!