ender 5 plus modifications 3d models

Bracket to mount the BTT Octopus Pro board inside the E5+ enclosure using the stock board mounting points. The stock Creality bed Mosfet is removed and the bed heater is driven directly by the Octopus board - bed heater wattage falls well within the...

This will help your rods being greased all the time when travelling up or down . the bracket will perfectly fit and slide over your bed and rod where you can ad a piece of foam keeping the rods greased and oiled all the time . 0.4 nozzle 0.2...

I created this remix to add in a CR Touch mount calibrated for a Revo Hemera on request. I'm currently using the Hemera V6/Colcano Part Cooling Duct by Hangtight but I haven't tested this CR Touch version as I have a BLTouch: ...

Remixed from https://www.thingiverse.com/thing:4790166 I needed a new enclosure for my 3KR EZ and loved this design, but it wouldn't work in its current form. Just did a simple adjustment to the screw holes and widened the USB/MICROSD slots and...

RPi Cam holder/mount. It is forward facing and rear mounted above the spool location. Swivels left and right and pivets up and down. 2/M5x10mm buttonheads bolts with T nuts and 1/M3x40mm bolts for pivet. ... Works for me.

Filament guide for relocating the filament spool to the side of the printer. Attaches to the back extrusion with m4x10 bolts and t-nuts. Mine is setup on the right side, but it can be mirrored to place on the left side of the printer. ...

This is a remix of someone else's design that I modified to work with the exoslide system. ...Drops the front bar by around 100mm.

This is a remix of the original: https://www.tinkercad.com/things/0MDHjpUZp1y The original design works well, but wanted to add some more rigidity and support. Added in two bolt holes that fit a M4x20 button head cap screw to be paired with M4...

These mounts are angled to solve clearance. The back one will clear my LED light strip and the front one mounts on the existing Micro Swiss threaded holes and clears the filament lever. I used 2 m3 screws to mount to the micro swiss and 1 m5...

The bolts on the bottom of the gantry mounting plate hit the middle of the bracket so i used tinkercad to hollow out a channel

The standard X-axis limit switch placement isn't exactly rock-solid. ...This mounting bracket adjusts the switch's position, ensuring a stable connection with the print head carriage instead.

The higher the infill the sturdier the mount. ...I recommend 30%.

This is a mix of the direct drive mount from paydayxray (https://www.thingiverse.com/thing:4310609) and the hot end side link from Gnizten (https://www.thingiverse.com/thing:4116655)

Designed up this dealer button to use in home games or have just as something laying around for any poker fan. It was inspired by a dealer button in Pokerstars VR. Printing: Ring - Infil to add weight, supports needed for spade inset. Letter...

Guida per Filamento PTFE in Direct drive. il connettore pneumatico è stato inserito scaldando la stampa e ammorbidendo la parte da filettare. il connettore è stato smontato dal slassico estrusore creality... quello che si sostituisce dopo 10 minuti...

24/12/20 A remix to hold a ptfe tube for a direct drive, seems to be useless and i already change spool position for a better performance i were getting some isues with cable management and as a result i changed it. ... changing the design for an...

After upgrading to linear rails there was nothing to trigger the endstop so I re-designed the x-axis endstop mount. designed and oriented so that the metal clip naturally rested on the micro switch rather than against it, works in conjunction with...

The X carriage wiring that comes stock does not have very good cable support. I designed this very simple mount that holds the cable loom in a vertical position. ...All that is needed to mount is QTY 2: M4 x 12mm screws QTY 2: M4 T Nuts

Just run the gcode from sd or octoprint Use feeler gauge or paper while adjusting knobs Category: 3D Printing Tests

<p>Require Parts:&nbsp;</p><ul><li>2x m3 t nuts</li><li>2x m3x16mm bolt</li><li>2x brass insert m3 (4.5mm outer 4-5mm length)</li><li>M3 bolt to secure fan onto heat insert, length depend on your fan thickness.&nbsp;</li></ul><p>&nbsp;</p><p>Install...

Right up front, I apologize - THIS IS A REMIX. Since Thingiverse REMOVED the ability to download all files that included identifying data on the thing you were downloading I could'nt find the original Thing number. That being said - if you designed...

I remove some space so it can fit. ...However, it may be possible that it is not quite as stable.

These models were draw up by another user I just modified. Front plate added a little more material to screw board in. Also change to 3-4 perimeters in screw areas where back plate screws to front gives more strength for tapping 3mm holes. Back plate...

This adaptor fits between the Microswiss and the Bigtree tech runout sensor

This bracket provides a direct drop-in replacement for the stock Creality mount, accommodating the BMG extruder and filament sensor seamlessly. However, initial attempts to install the BMG extruder revealed that the filament path didn't align...

This routes the hot exhaust from the mean well power supply out the side of the case instead of across the mainboard. ... Print with support touching the build plate.

I needed a taller version to prevent my cables from hitting the homing sensors. ... Feel free to make changes.

Decided to try my hand at designing my own model. Was needing a case for both of these components, I am slowly working my way to building the Mercury one.1. Only designs I could find required me to cut my stock enclosure, which I did not want to do.

My setup is weird. So I needed a specific mount to make my printer Direct Drive. If I'm not the only one, here's the file. ... The Updated V7 File includes a slight adjustment to the motor placement to account for variations in HeroMe spacing.

This print is made for testing whether you have set your bed correctly or not. The print is one layer thick and doesn't take long. ...