ender 5 plus modifications 3d models

I appreciated how solidly designed the BL touch mounting tab was on the original version, and how the Hemera mounting points resemble standoffs rather than a single large square, allowing for improved airflow around it. I didn't require the run-out...

I was going to make Gnizten's model when I saw that they already did it! Thanks! However, I try to print support free, and his model was on an angle which is an issue for some. I adjusted the angle, removed the lip to make the front flat, and put...

After upgrading to linear rails there was nothing to trigger the endstop so I re-designed the x-axis endstop mount. designed and oriented so that the metal clip naturally rested on the micro switch rather than against it, works in conjunction with...

I have revised this mount so that it also reaches the x endstop I also installed a reverse bowden mount have fun printing

I used this design for my linear rail conversion, I'd used others but this one I felt had better Y brackets and the X cartridge bracket was great. The bit that I liked the most was the ability for you to print the X gantry without supports, the...

<p>This is a remix of the linear rail X-Axis conversion kit by <a href="https://www.thingiverse.com/SnakeP">SnakeP</a> on <a href="https://www.thingiverse.com/thing:3782865">thingiverse</a>.</p><p>It's different in 4 ways:</p><ol><li>a bit easier to...

This Spool Holder is adapted on a extended Frame of the printer, you must have 2 ball bearings APEC-7 608zz 8x22x7mm. ...You can mount it on the Alu Profile 20x20 with 3-5mm Slot T-NutsThe Frame Extension is made of Alu Profiles 20x20 Nut 6Alu...

Yet another set of standoffs. I made this version because I did not have a right-angle USB-B cable and I did not want to drill in the case. This moves the board flush with the heater control MOSFET and leaves margin on the side for USB cable. ... ...

Soporte para sustituir placa original al mover el extrusor y el motor para extrusion directa. Añado filtro limpieza filtro disponible en: https://www.thingiverse.com/thing:4348381 Support to replace original plate when moving the extruder and...

This bracket lays flat on the printer case. It is designed to allow for the use of a Right Angle USB B to USB C Adapter so a Panel Mount Coupler, USB C Female to Type C Female can be mounted to the case. Works great for using Klipper on a Raspberry...

https://www.thingiverse.com/thing:4441076 presented a thumb screw to replace the wing nut on the front-left corner of the BIBO bed. It is too wide for the other two positions. I have created a smaller version to fit the right-front corner and the...

Filamentsensor adapter plate 6mm thick when you upgrade to an dual gear extruder

<p>Very quick and easy bed leveling test. ...The squares are 20mm each placed on every corner and middle of the bed.&nbsp;</p>

El remix anterior no encajaba pro que el tornillo es de cabeza grande, le he hecho el hueco mas grande para que pueda entrar sin tener que cambiar el tornillo. ... The previous remix did not fit because the screw has a large head, I have made the hole...

Utilizing more build plate surface with adjustable end-stop switch holders for X and Y axis, utilizing original switch board. ... X-endstop is lifted upright to make room for cable holder on MicroSwiss NG since original one does interfere with secure...

After installing the MicroSwiss all metal hotend and direct drive system the cables kept hitting the extruder and the filament lever. So I designed this cable guide that has an arm that rests on the extruder body and can be secured with an M3 x 15...

Simple but working drag chain mounts for the E5P and Biqu Hermit Crab. Uses an inexpensive 10x11 drag chain from Amazon. The Y motor mount was from somewhere else but I modified it to fit a larger motor. If anyone find the link to it, I will be...

To comply with European regulations, I've replaced the original power supply with one that meets EU standards. Since my design expertise is still developing, I tweaked the fan output manually to ensure a smoother performance. The reorganized wiring...

I've been using the SpeedDrive mount as modified by @paydayxray for quite a while now, but haven't been thrilled about cable-tying the wire loom to the extruder spring or release lever. So I added a sturdy cable support. It looks a bit fragile at...

Basic support to subject you carriage cables. Supports aren't needed if you use resolution 0,12mm and your funs works fine. UPDATES: · 10/05/2021 v.1.1 Modified width in the arms to ensure 3mm, to give more consistency. ... BOM: · 2 x M3...

A simple filament sensor adapter for direct drive and dry box setups. It's meant to just snap on to your existing filament sensor. No disassembly of your current sensor is needed. Just print this out, pull out your filament, pop this sucker on and...

Customized version of https://www.thingiverse.com/thing:3507663 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=3507663

Drill and tap the Y bearing bracket using the mount as a template. can be mounted on any side of the Y axle. 4x M3 brass inserts 6x M3x8 screws S42B Servo can only be used on motherboards with removable drivers. ...ex: SKR 1.4 , GTR, ,etc,etc,, ...

Quick print. ...Created this because tube would get stuck there from them to time...

Hello, Here is a support bracket for cable from print head. Part 1 should be printed on its back : the bigger flat part Part 2 should be printed as well on the bigger flat part : on photo part 2 is printed twice Part 3 is meant to hang the card...

I will add photos once I have everything tidied up a bitThis houses the RPi so that the SD card can be accessed. All connectors are otherwise locked up inside the enclosure. I modeled a couple small support tabs inside the card slot so you can print...

<p>RPi Cam holder/mount. It is forward facing and rear mounted above the spool location. Swivels left and right and pivets up and down. ...2/M5x10mm buttonheads bolts with T nuts and 1/M3x40mm bolts for pivet.</p> <p>Works for me.</p> Category: 3D...

Two side mount and the spacer/washer for mount to the frame print 4x of it

Disclaimer: I am not at all good at 3d modeling. I used Tinkercad to splice this up with some other mounting plate. ...Haven't tested/mounted it yet but it printed fine