ender 5 plus vs ender 3 s1 plus 3d models

My ender 5 plus factory spec out the box has this additional dampening bracket. Which needs slightly more space for the cover to fit properly. Test prints fit perfectly. Use the same fastening / fixtures listed in the original. ...Worked a treat.

Using the BondTech BMG/V6/Volcano direct drive for Creality Printers by Hangtight on MyMiniFactory with the Ender 5 Plus can lead to a problem where the BLtouch doesn't trigger before the nozzle hits the bed. The BLtouch adapter screws in exactly...

This is a remix of the switch mount for the 3DChameleon MK2 that fits in the rear left corner of the Ender 5 Plus sitting ontop of the corner bracket allowing for you to use the Y axis to trigger the switch. The switch ends up triggering at the same...

If you own an Ender 5 Plus and install the Printermods MDD 1.2 direct drive plate, you'll discover that the stock metal BLTouch mounting plate won't fit properly. None of the pre-printed BLTouch mounts match, so I chose to modify the metal one...

Mount for the Adafruit ADXL343 Accelerometer that works on a Ender 5 Plus with BLTouch. ... **Parts Required** - Adafruit ADXL343 [on Amazon](https://www.amazon.com/gp/product/B07PN6ZBJF/) - 2x M3*20mm Hex Socket Head Cap Screws and Nuts [on...

# WHAT THIS 3D PRINT IS NEEDED FOR AND WHY IT WAS DEVELOPED: This 3D print resulted from the fact that after a while the cable guide of my Ender 5 plus kept bending towards the heatbed due to the weight. After a while, the cable guide was so deep...

I'm Sick of Long Bowden Tubes and Backordered Hemeras, So I Designed a Direct Drive Mount for My Ender 5 Plus. I'd had it with the lengthy Bowden tube that always seemed to be in my way. Then, when I was ready to upgrade to a Hemera, it went out of...

After purchasing Exoslides for my Ender 5 Plus I found that the H2 adapter wasn't compatible with the exoslide. Installing this requires disassembling the H2 to screw the center section of the extruder to the adapter. Next step is to connect the...

Snaps perfectly to the frame of the Ender Creality 5 Plus. The camera can be locked into place by rotating it onto the mount. Print orientation: Best printed on its side otherwise the print lines will be too weak and the snapfit part might...

This is a Cable Holder for the Ender 5 Plus with linear rails and the Micro Swiss Direct Drive I use this cable chains 20x10mm: https://www.aliexpress.com/item/32999589537.html?spm=a2g0s.9042311.0.0.27424c4dZDh4ri I use the cable chain trays from...

Use the same information as the original file, this just adds a slot to store one additional SD card on the side From original: So I made this thing for my Ender 5 Plus +, you need a couple of M3 or M4 x 10 bolts and T-nuts to attach it. I also put a...

This is an enclosure I made for upgrading my Ender 5 Plus with a BTT board (mount inside the Ender's enclosure) so I can use the TFT35 E3 V3 display as well as a Raspberry Pi with its own HDMI display. I have blocked off one of the USB sockets on...

This is a custom mount designed specifically for the iUniker Raspberry Pi Armor Case, which perfectly fits on the Creality Ender Five Plus. ...To assemble this mount, you will need two M5 8mm flat screws that come equipped with T-nuts.

https://www.thingiverse.com/thing:2802474 Lastly, you will need to elevate the Ender 5 Plus with bigger feet so the fans have room to move air. These are a cool design that use squash balls to limit vibration ...

See the original creator here: https://www.printables.com/model/436006-ender-5-plus-with-microswiss-ng-cable-chain The original creator made these for a 10x15 cable chain that was purchased from Amazon. He used the closed version of the chain,...

No Support needed, 4 brackets needed for Ender 5-Plus I made this adapter to quickly fix the Z-Rod height on my Ender 5-Plus while using the Mini-Me Mosquito mount to avoid collisions. The BL Touch needs to be spaced down about 15mm to be used in...

To attach the raiser to the frame of the Ender 5 Plus you can simply use M3, M4 or M5 T-Nuts. You can get them here: ...

Hier meine eigene Konstruktion für ein Phaetus Rapido HF, LDO Orbiter V2.0 an einem Ender 5 Plus mit Linear Schiene. 2 x 5015 Bauteil Lüfter, 4010 oder 4020 Hotendlüfter, BL Touch Halterung und Kabelführung nach oben. Lege die Fusion Datei mit...

Hello all out there, here is my proposale for ender 5 plus power supply. Hummm no ... In fact, the support is designed for a weanwell power supply RSP-500-24. It schould fit any 3D printer based on 2020 profile frame. The support is designed to...

An all in one BIQU H2 Extruder mount for an Ender 5 or five plus, X and Y end stop mounts are from from a linear rail upgrade kit. I've uploaded a couple remixes, of the Y enstop I think the V2 should be about right as the V1 was too Small Nozzle was...

This print is for side mounted light bars for the Ender 5 Plus. I wanted them on the sides so they were out of my way and have two light bars for better lighting. The brackets are RH / LH so the X axis motor on the gantry is the RH bracket. I also...

This includes two lengths of bracket designed to move the standard spool holder bracket 25 mm or 50 mm rearward on the Ender 5 Plus. This allows for the use of large replacement spool holders such as the design this is a partial remix of. The newly...

A "filler" type spool holder that can hold 3 kg of filament on the back of the Ender 5 Plus, without interfering with the printbed. It does not protrude further at the back of your printer than the x-axis motor, so the footprint of the machine...

Hier habe ich euch mal die nötigen Abdeckungen hochgeladen um die seitlichen und unteren Schlitze am Ender 5 Plus Gehäuse zu schließen. Somit Könnt ihr dann mit meinem Dual Noctua 92x14mm Umbau eine perfekte Strömungslüftung erzeugen. Die Löcher hab...

Creality Ender 5 Plus Easier Feeding the Feeder It can be difficult to insert the filament into the Feeding Units because they are generally below the print bed. This bracket raises the Filament Feeding Units higher for easier access... it Mounts...

I am working on an improvement to this model; so so not print it at this time.  Creality Ender 5 Plus Ring fan duct.To blow air around the 3D printed part.Uses two blower fans for the part and a hot end fan.This unit moves the Hot End forward so the...

Creality Ender 5 Plus Easier Feeding the Feeder It can be difficult to insert the filament into the Feeding Units because they are generally below the print bed. This bracket raises the Filament Feeding Units higher for easier access... it Mounts...

I needed a mount for my TH3D EZABL and and wire loom support to help with that giant loom the Ender 5 Plus is doomed with. Its not perfect as the fit and finish is off (Chamfer) on a couple spots that I couldn't figure out. I included the STEP file...

Direct drive mount for BMG extruder on an Ender 5 Plus, suits either stock, Dragon or Mosquito hotends. Hotends are mounted directly to bracket for rigidity and one-handed nozzle changes. All other stock Creality parts and hardware are reused...

An end cover for the Ender 5 Plus to cover the sharp edges of the exposed beams when relocating the crossbar. Design updated to provide stiffness even with the metal brackets at the corners loose. One left and one right model needs to be printed....