ender 5 plus vs ender 3 s1 plus 3d models

Ender 5 Plus Z motor cover in two parts. Fits between the coupling of the Z screw and the motor plate. It fits around the motor shaft to prevent debris from getting into the motor bearing. ...Ive made it with 4 holes for 1.75 filament, small screws or...

This is an external mount for the 500W Meanwell power supply ( RSP-500-24 ) that comes with the Ender 5 Plus. It consists of a top cover, bottom cover, and power switch/plug holder with a cover. The power switch/plug holder uses the existing power...

Ender 5 Plus BTT smart filament sensor mount, this goes in the place of the stock sensor and uses the same M4 bolts and T nuts. ...Wire management for the hot end wiring to bring the wires off of the back extrusion to make way for top enclosure.

SKR PRO board holder for Ender 5 Plus printer.It does not require mechanical modifications, the cables to the drivers can be stored under the board.Use the original holes and screws to attach the bracket. ...Screw the board to the holder with a 3mm...

Copy of cable guides that came with the Ender 5 Plus for the X-axis stepper and limit switch cable. ... It allows the cable to slide through as the gantry moves back to front.Should work with any 20 mm aluminum extrusion framing.

This is a Remix of a Cable Support for the Ender 5 Plus. But i didnt find that Thing again on Thingi. I just made the space between the holder bigger so it fits with the original BL-Touch Plate. ... You have to ad support to the holder but not to...

This is a rapid and makeshift spacer designed to enable an E3D Hemera Bowden to be securely attached to an Ender-5 Plus printer. ... It shifts the stock filament sensor away from the extruder bracket, allowing its filament path to align perfectly with...

This display holder was specifically designed for a Big TreeTech TFT24 V1.1, allowing it to be mounted in an Ender 5 plus. ...To install the new holder, removal of the old display is necessary so it can be easily seated.

Wanted to test out HexOrt inspired wobble wings on the ender 5 plus to see if it would help with layers lines. After about 2 months of testing, I can say they have significantly reduced layers lines on most of my prints. ... Will Need: 10mm Magnets ...

However, the following text has been rewritten: The Enders 5 Plus bed is connected to a cable that keeps it safe. ...To secure the cable, just snap it into place in the square hole and tie it up with some cable ties, just like you see in this picture.

This gasket has the screw holes oversized and spaced to fit the stand-offs in the Ender 5 Plus's case. ... I noticed a slight whistle and visible gap between my fan and the case; it probably would not be an issue for most people but my printer is in...

This adapter makes it simple to install the Mean Well RSP-500-24 power supply unit in your Ender 5 Plus machine. You will need (8) M4 x 8mm button head screws and (4) M4 nuts for this installation. The adapter does not demand that you extend any...

Ender 5 Plus bed cable support. Wanted one which was simple, solid and didn't require additional parts. To install just remove the two screws on the bed frame, slide the support in and reinsert the screws. ...The screws don't touch the support, they...

Wanted to test out HexOrt inspired wobble wings on the ender 5 plus to see if it would help with layers lines. After about 2 months of testing, I can say they have significantly reduced layers lines on most of my prints. ...Will Need: 10mm Magnets 3mm...

A custom bracket designed to securely house the stock Ender 5 Plus filament sensor following a direct drive upgrade, also incorporating a built-in filament dust filter assembly for enhanced print quality and reduced maintenance. ... The mounting arm...

The Ender 5 plus's location on this design smacks the Bl touch on the Z rails when homing, moving it out of the way but still requiring offset changes to avoid hitting the left-hand side Z rods. ...I adjusted these offsets in the starting gcode within...

I did a remix of the Ender 5 plus hemera mount https://www.thingiverse.com/thing:4026886. but found that the nozzle was sitting higher then the wheel on the rail making it impossible to level. so I lowered the mount holes by 3mm and that gave me...

This is a DIN rail mount for the Ender 5 Plus MOSFET.  It is a snap fit and requires no hardware to mount the MOSFET, though M3 screws could be used if you want.  I printed mine out of PETG for a bit of flexibility. ... STEP file included incase you...

This mount seamlessly integrates both the BLTouch and filament run out sensor that come standard with the Ender 5 Plus. It attaches securely to the stock metal mounting bracket, so I'm confident it will be compatible with every printer in the Ender...

remixed feet from ender 3 for ender 5-s1 simply unscrew old feet and re-use the screw with the provided holes in the model

All parts are for the Creality Ender 5 Plus. The light strip can easily be stuck around the corners and you need less than 3 meters from the light stripes. Required parts: - 2 pieces AngleBar1 - 2 pieces AngleBar2 - 2 pieces...

Modded the Threaded Dust Filter by Kezat so it would be compatible with the Creality Sprite extruders. The original design is awesome because, unlike other designs I've seen, with this one, to apply the filter you don't have to completely remove...

Modded the Threaded Dust Filter by Kezat so it would be compatible with the Creality Sprite extruders. The original design is awesome because, unlike other designs I've seen, with this one, to apply the filter you don't have to completely remove the...

This is a mount for the iUniker Raspberry Pi Armor Case for the Creality Ender Five Plus. ...It requires 2 M5 8MM Flat Screws with T-Nuts Category: 3D Printer Accessories

This is a mount for the iUniker Raspberry Pi Armor Case for the Creality Ender Five Plus. ...It requires 2 M5 8MM Flat Screws with T-Nuts Category: 3D Printer Accessories

A few changes were needed to get this to fit on my Ender 5 Plus. I went with spacers to adjust the Z. On the Micro Swiss Direct drive there was no need for the cut out area so I removed it to increase strength. This will print with no supports .

This fits the Ender 5 Plus but should also work with other printers with the same hotend housing. Notes: - You'll need 2xM3 20mm screws and 2xM3 nuts to attach the 4020 fan to the adapter. ... - Reuse the M2.5 mounting screws and air duct to attach...

The ones available didn't match up with the bolt pattern on the 5 Plus' lead screws. Suggest Printing at 100% infill with 0.12 layer height and 4 walls. Uses M3x8mm to attach to brass nut and M3x10/12mm to attach to Z Gantry Bar. Print Settings...

My Ender 5 Plus was extremely loud, so I changed all its fans. The loud one at the nozzle was swapped with a 40x20mm Cooltek one (very nice result) and so it did not fit into the normal metal duct. This one is designed in the same style, only...

I made this tool carriage the same length as the stock Ender 5 Plus's tool carriage, with similar 'hooks' to continue to use the stock belt with it's crimps. STEP file is include if folk want to adapt it to their own machine. ...Unfortunately,...