endotracheal tube rack 3d models
98789 3d models found related to endotracheal tube rack.thingiverse
This is an endotracheal tube rack for tubing sizes between 10mm - 3mm in 0.5mm increments. Each slot is 2mm larger than the labeled size for ease of use. ...I have split the model into two halves, one with 10-7mm and one from 6.5-3mm for easier printing...
thingiverse
I developed this lid for the endotracheal tube to decrease the risk of contamination during endotracheal intubation, especially in patients with COVID-19. ...There are two versions: one completely closed and one with a 4.7mm introducer hole.
thingiverse
Endotracheal Tube Holder, FINAL DESIGN UPLOADED. Works well and can be used well. Need an elastic band or some sort of head tie so it can be wrapped around, use cotton pads or any foam to be attached to the cheek pads. ... GB
thingiverse
This endotracheal tube clamp could be used to prevent aerosol or droplet spread from an intubated COVID-19 patient. It was remixed from https://www.thingiverse.com/thing:4271154. 1. Detachable design. Now, in order to apply the clamp, you...
thingiverse
Endotracheal tube fastener : This was designed based around a request posted on 3D printing reddit page. All the measurements are roughly guessed after watching related videos on youtube. All the parts are designed to be able to 3D print So issues...
thingiverse
This is a disconnection wedge used as a lever on the 15mm male connector to disconnect the ventilator circuit connector from the attachments (endotracheal tube or tracheostomy tube) without pulling, pushing or twisting which may cause pain or...
thingiverse
Clamp Endotracheal tube with finger support Based on https://www.facebook.com/groups/clamporotraqueal/permalink/685648202014013/ but with modifications to the finger support for more area, better grip and fewer injuries. ... Work in tubes with...
thingiverse
This fixator can be used in orotracheal tubes so that after intubation, better stabilization is achieved, reducing the risk of involuntary extubation. It has been tested in tubes with the following measures: 5.0 ~ 9.5 I do not recommend using PLA...
thingiverse
I was warned that there was a shortage of these clamps in local hospitals. These clamps are used when intubating patients to prevent the spread of any infectious diseases they might have. <h3>Usage:</h3> If you are planning to use this device: ...
prusaprinters
<p>I was warned that there was a shortage of these clamps in local hospitals. These clamps are used when intubating patients to prevent the spread of any infectious diseases they might have.</p> <h3>Usage:</h3><p>If you are planning to use this...
thingiverse
This clamp can be used in the orotracheal tube to temporarily block air while health professionals are tubing sick people with COVID19 (Coronavirus), reducing the chance to get infected. It was tested with these dimensions (inner diameter): ...
thingiverse
Tube rack holder. can be used for 15ml tubes or conical tubes. Racks from companies run from $50-%100, this rack can be printed for ~$3. ... Visit our website at: www.downloadablelabs.com
thingiverse
Tube rack for noble gas tubes. Print with letter sides down 20% infill and with/without support. ...
thingiverse
This is a tube rack with a .5in holes and it makes a good pencil, tube, or tool holder for your work area. ...i made this for a science teacher for my school.
thingiverse
This plastic Z-shaped rack is designed for holding 2 50ml tubes, 4 15 ml tubes and 5 eppies. It can be personalized by adding a text in the middle. The Z-shaped is sturdy and limits required material for printing. Can be printed without supports but...
thingiverse
It is a test tube rack, to present them with a sort of carousel. ...More pics here :http://www.flickr.com/photos/watsdesign/sets/72157625557594408/ Instructions Print : 2 discs, 2 spacers, 1 base And...
prusaprinters
can be used as a rack on your lab bench, printed with ASA for chemical resistance
cults3d
... diameters. It was designed for tubes that are Ø=52mm, so that is the default diameter. The zip ties used at the original scale are 4,8mm wide and need to be minimum 250mm long to assemble this comfortably but shorter could work. ...Ours was 300mm.
myminifactory
... It was designed for tubes that are outer Ø=52mm, so that is the default diameter. The zip ties used at the original scale are 4,8mm wide and need to be minimum 250mm long to assemble this comfortably but shorter could work. ...Ours was 300mm.
myminifactory
Intubation stopper for use with endotracheal tube in the medical process. ... Recommended filament: TPU (thermoplastic polyurethane) Measures: Large: 4.5mm diameter holeMedium: 3.77mm diameter holeSmall: 2.75mm diameter hole Creators: Rafael Taveira...
thingiverse
Here is a simple snap in rack that works with my industrial paper towel tube caps.