esp32 s 3d models

This is the enclosure designed specifically for the ESP32 Marauder.\r\n\r\nKey components of the project:\r\n- The ESP32 Marauder\r\n- 4 M2.5x10 Hex screws\r\n- Enclosure face plate\r\n- Enclosure body\r\n\r\nHow to assemble the enclosure:\r\n\r\n1.

Required components besides the two printed parts: wrover esp32-cam module two nuts M5 four screws, 60° head, M3x16 (screwed directly into the plastic) For best firmware I found for this module, please refer to this GitHub repository:...

I made this design to use it with ESP32-CAM and a MicroUSB board to plug it.To have the thinnest case possible, I cut the PINs that are too long.ESP32-Cam on Aliexpress hereMicroUSB Board hereTutorial to configure it with tasmota firmware here (In...

Rhasspy Dot Case for Matrix Voice ESP32 and Speakers Slim modular offline voice assistant case Assemby: print all parts glue the fabric to the cover - i used superglue cut the fabric leftovers from the cover mount the matrix voice hat with 2 small...

There is plenty of ESP32 board enclosures out there, but most of them are quite streamlined/minimalistic, which is fine but I set out to buid an enclosure with a little more room in it so you can easily use breadboard jumpers instead of soldering,...

I'm working on a project using an ESP32 to read temperature and humidity data from Bluetooth sensors. As I moved around the house to set up the initial prototype, I made the decision to quickly assemble a makeshift enclosure for it. The current...

Components: - 4 standard 6mm potentiometers (linear 10k ohm) - 2 KY-023 joystick modules - SSD1306 128x64 1.3" I2C OLED display - ESP32 (DOIT DEVKIT V1) - nRF24l01 PA+LNA 2.4GHz module - 4 DPDT switches - 2000mAh 5V USB powerbank The bottom and top...

... The lid is a one lid fits all. I hope this helps someone out: Box i built for Sound Reactive builds of WLED to attach a microphone: https://www.printables.com/model/317718-esp32-wled-sound-reactive-box https://www.thingiverse.com/thing:5631371

This nano data center is based on a Wemos D1 min ESP32 and has a 24 neopixel ring integrated (for optical alarms etc.) and a SPI port, for external connection of a nRF24 or LoRa module, is provided. All parts stick together and hold. No glue or...

Simple enclosure for the very nice ESP32 Louder Board from sonocotta.The lid is angled on the short sides, so that you can "clip" it on the base.Maybe you have to edit the tolerances to fit if your printer is better calibrated then mine.Added some...

Window mount for your ESP32-CAM board Mounted with double-stick tape directly to the window make it possible to stick inside to show the outside with minimal reflections. The mount tilts the camera upwards and not straight forward. Used as a...

DIY Case for ESP32 V1 DIY board by AWOK, to be used with board from [AWOKMUSIC](https://awokmusic.square.site/shop/electronics/3?page=1&limit=60&sort_by=category_order&sort_order=asc) Holes are made for 4 14mm m3 screws *Be sure to double check the...

I bought this ESP32 ( https://www.aliexpress.com/item/32819907815.html?spm=a2g0s.9042311.0.0.39b54c4dZwsiTr ) to integrate in Home Assistant, but I did not like the "naked" look, so I decided to create a simple enclousure. It has no locking...

There is plenty of ESP32 board enclosures out there, but most of them are quite streamlined/minimalistic, which is fine but I set out to buid an enclosure with a little more room in it so you can easily use breadboard jumpers instead of soldering,...

This base has four 11x3mm cavitys for 10x2mm magnets on the backside.To watch our powermeter via "ai on the edge" firmware on the esp32-cam modul + green USB micro breakout board, I needed a flexible but sturdy solution to get the position right.With...

... and time information by previously synchronizing its clock through an NTP server. This transmitter is built from the ESP32 module, coupling a small 64x48 pixel 0.66-inch OLED display. ... First version: https://www.thingiverse.com/thing:3601407

I adjusted it a little because I wanted to connect the ESP32 with a USB socket. To do this I had to enlarge the case and create a new lid.In my case, the glass on the water meter was extremely reflective, so I installed a lens on the camera light for...

... The lid is a one lid fits all. I hope this helps someone out: Box i built for Sound Reactive builds of WLED to attach a microphone: https://www.printables.com/model/317718-esp32-wled-sound-reactive-box https://www.thingiverse.com/thing:5631371

External Antenna Version of ESP32 WROOM Module The ESP32 WROOM module is a highly integrated Wi-Fi and Bluetooth wireless communication solution that provides an easy-to-use interface for various applications, including IoT, robotics, and more. The...

Things Needed: Ai-thinker ESP32 cam 16 Led Neopixel Ring M3 Screws (5mm) M3 threaded inserts OD- 4mm (Optional) 3.5mm DC male/ female connector 5V Power Supply (Can use buck converter to lower the voltage of printer power supply from 24v to 5v)...

This housing is intended for outdoor use of the ESP32-Cam microcontroller. There are fixtures for 5mm LEDs. I use infrared LEDs, so the camera can be used in the dark without visible light. But this requires a small modification of the ESP32 cam...

Required Components: - Wrover ESP32-CAM module - Two nuts M5 - Four screws with 60° heads, M3x16 (directly screwed into plastic) For optimal firmware performance on this module, refer to the GitHub repository at...

ThermIQ (www.thermiq.net) interface card för Thermia heatpumps, enables support for use via home assistant HASS, This is a case for the ThermiQ-ROOM2 i got delivered in early 2022, note that deliverys later in 2022 is built with addon boards ( so...

Compact enclosure for the ubiquitous ESP32-CAM with the USB-Serial board and an external antenna. The program- and reset-button are still accessible through the cooling slits. Update: SD-Card also accesible now! The holes in the bottom piece...

A 3D printed ‘box’, designed as separate box sides that bolt/screw together, to not only make printing easier, but also to allow the sensor and ESP32 components to be easily assembled inside the ‘box’.The ‘bolting together’ is accomplished by...

I've made this box for wallmount for a combined esp32 cam (blank camera is also shown on the picture). Not sure if all of these sold are within the same measurement, so I uploaded the fusion360 file. All parts/bodies are seperated by 0.1mm in this...

ESP32 NodeMcu - Case (Lolin V3 no rounded corners) Designed this case because I did not like most of the designs out there. This one fixed all the issues and I'm happy with that hope other people enjoy as well. The lid holds into a grove and the...

This cube box was specifically designed for the ESP32-EVB board. I intentionally left the buttons unattached from the top object, making it easy to add them separately as needed. My main intention behind creating this model was to control my AC using...

Using this clamp you can mount the camera module on a ESP32-Cam board in two orientations. For 90° rotation carefully fold the flex-print cable as shown and put some foam below the camera module, then snap the clamp on. Print Settings Printer Brand:...

This is design to work with a the ESP32-Cam case designed by SolarGermany https://www.thingiverse.com/thing:3949787/makes Print Settings Printer Brand: Creality Printer: Ender 3 Rafts: No Supports: No Resolution: 200 Infill: 15 Filament: PolyMaker...