eurorack case 3d models

This is my first take on a mount for the DSO138 Oscilloscope tailored specifically for Eurorack modular Synthesizers. I'm eager to receive feedback, as it's always welcome. ... The Oscilloscope that I used for this project can be found here:...

Here is an experimental bracket for a Eurorack modular synthesizer, designed to seamlessly integrate with the Parametric Eurorack Rail. Although it works nicely with my own rail system, there are numerous variables to adjust, allowing you to...

Here's a 4HP wide 3D printable panel for a Eurorack style passive multi. It accommodates up to eight 3.5mm mono sockets. The panel is designed thick so that it doesn't flex when the jacks are pushed in, but you may need longer than standard m3 screws...

The "Eurorack patch cable hook" is a hook for Eurorack module synthesizer (e.g. for the Doepfer® A-100® system). It can be used to get hanging patch cables out of the way.The hook is designed to sit on the edge of a module and is secured with one of...

Eurorack frontplate for DSO 138. Its a modified case. ...Selfexplaining i guess :)

Here is a .SCAD file for creating blank Eurorack panels that requires minimal effort to use; simply specify the desired hp, the total number of mounting holes (top and bottom combined), and an optional hole width parameter (defaulting to 5.08mm) if...

This is an Ali-franken Eurorack module. It can be described as a 3 channel mixer, 2 mono and 1 stereo, where the mono signals can have Reverb FX. Taking a cheap reverb for microphone circuit, adding some resistors to attenuate the signal (from mic...

I needed a compact speaker for my eurorack system and was surprised to find limited options available. While browsing online, I stumbled upon the IKEA FREKVENS portable speaker, priced at 17.99 Euro. Since I'm a fan of Teenage Engineering's design...

Just a simple screw for Eurorack synth to avoid scratches and screwdrivers. I've successfully printed this tiny screw with a 0.1mm layer height and increased the wall line count to simulate a 100% infill. You can also simply use a 100% infill, of...

Easely printable rail with solid structure inspired by the Nifty case. ...

I created this so my Behringer MX602A stand on top of my modular synth case and have good access to the controls. It uses the same screws that hold on the original side plates. Printed fine for me without supports. ... Made in Fusion 360.

simple Euro Rack Mount details for screwing see remix source still in progress I am looking that all can fit V8 The lower hole is for a USB C extension and the slot for midi cable V9 is with normal USB B extension and Audio jacks The USB you have to...

Supports attach through the underside(obviously) but the "leg" needs to be long enough to touch the bottom of your case. Plan ahead, if you know you are going to have to print multiple rails to get the hp you need and you know what modules you...

The thing is pretty inexpensive at about 12$US and I have a printer at the house, so I thought I'd crank a rough faceplate out in OpenSCAD and TinkerCad I haven't tried it, yet, and I don't know that it will go smoothly so maybe disconnect your other...

Poorly written explanation: I sold a few Eurorack modules freeing up space from my modular case. I didn't need any new gear so I decided to use the space with some other gear from my desk (so I wouldn't have so much empty space tempting me to get...

Eurorack card holder for TipTop Audio Z-DSP Cards. Fits 5 Cards. ... 1 TE widths

Users Fabricated a Set of Blank Eurorack Panel Covers Featuring the Moog Logo in Diverse Angles.

Simple 3-horsepower passive 1x7 or 2x4 multi for Eurorack module.

8HP eurorack panel for 3 effects modules (look for "99 DSP effects" on aliexpress).

This is an adapter designed for mounting the Korg SQ-1 sequencer within a Eurorack modular synthesizer case. For the lower section, I created two legs that prevent the SQ-1 from falling backwards inside the case and enhance its stability. These are...

It will give you an additional 1.5mm of clearance, which can be all it takes to fit a deeper module in a skiff case. I used it to fit a Brain Seed into an Intellijel Palette, and I'm very happy with the results. Longer screws (8mm) are...

Skiff box to convert the Synthrotek Nandamonium eurorack module to console. Also works as a 38HP eurorack skiff. Drill your own holes! ... Remixed from https://www.thingiverse.com/thing:4704601/files

8 HP eurorack panel for eurorack clock module Circuit by Synthmafia: 1. ...https://create.arduino.cc/projecthub/Synthemafia/modular-synth-clock-module-diy-arduino-sm-tik-tak-bd8ded?ref=user&ref_id=530336&offset=1

2hp panel for holding MicroSD cards. ...Great for people that can't have too many samples in their Eurorack.

Free standing rails for Eurorack modular panel. Convenient for working on modules. ...Requires (4) 3mm heat set inserts.

Clip to hold the inexpensive FNIRSI-138 oscilloscope to a Eurorack rail. I use a 3D-printed 42HP rail I designed. ...

A set of two different 2HP eurorack panels for cable management. ...One version has two less pegs to facilitate hand tightening of knurlies.

Powering the module can be done by the micro-USB port, but it should be possible to power it from the eurorack power supply by soldering jumper cables to suitable places on the mainboard (NTS-1 has several HW revision so it's possible that the newer...

A simple brace to hold both ends a eurorack power cable so you can test connectivity with a mulitmetre. ...I insert headers into each end so you have exposed pins to test.

M3 Threaded insert for eurorack, tiles so you can print out many and stack them. Will make it parametric one day. ... Print it in the toughest filament you've got, this is going to be holding some serious money ;)