evolv dna 250c box mod mount 3d models

... difficulties inserting and ejecting the memory card, so I enlarged the slot slightly at the rear. ... Additionally, I needed to gain access to the GPIO pins, as well as the connections for the camera, display, and a fan mounted on top of the device.

Had trouble getting the memory card in and out, so made the hole at the back a bit bigger. Also wanted access to gpio, camera cable, monitor cable, and a fan mount on the top Print instructionsCategory: Electronics

If you're not in the mood to swap out all three Control Box fans, you can simply use a single 120mm exhaust fan, which has more than enough airflow and will cost significantly less. You'll want to connect the fan to one of the 12v connectors on the...

I was having a blast figuring out how to get the teeth to print for the Venus Box. The tiny semi-circular hinge kept failing every time I tried. So, I added a small leg for extra support (mirroring the original design without teeth) and that seemed...

I included cut lines in the model, and I printed the box with PETG vs PLA to withstand the heat generated by the heat gun, which seems to work perfectly. The vacuum hose hole is 35mm, so trim or fill it to fit your vacuum hose. To hold the...

If you don't fancy replacing all 3 of the Control Box fans you can just use a single 120mm exhaust, it has more than enough air flow and will cost a lot less. You'll want to wire the fan to one of the 12v connectors on the motherboard, rather than...

I've made a slightly modified version of my TAZRantula (Tevo Tarantula Mod) Z-Mount, specifically tailored for my custom TAZRantula duel kit mod. This Z-Mount Remix can work seamlessly with either single or dual Z-stepper motors/rods. ...Note that it...

I'm modifying the Z-Mount Remix for my custom TAZRantula, a Tevo Tarantula dual kit mod. This upgrade is compatible with the upgraded or fixed Z-Nut mount. It supports both single and dual Z-stepper motors or rods. Print Settings Printer Brand:...

To be used with https://www.thingiverse.com/thing:3714121 - Link Mod.STL I needed a Pi camera mount that linked into the Link Mod to mount to my Anycubic Vyper. This can be used with any printer though. ... Standard PLA settings: 195C nozzle 60C...

I ended up not finding a BLTouch mount that would work with Chanh Phuong's excellent fan duct for the Artillery BMG mod, so I decided to roll my own solution. ...It turns out it works perfectly with the bracket from the Waggster mod.

If you enjoyed this content and would like to show your appreciation, consider making a donation at paypal.me/maxgreco1.

This part is a modification of the Method Spool Mount to support a spool of filament located above the machine instead of mounted to the machine directly. I removed the spool mount, changed the angle of the PTFE Tube, and tightened up the tolerances...

VX1000 Mic Mod Tripod Mount This is a ¼”-20 Tripod mount for the Sony VX1000 Microphone. Using the Mic’s original rubber grommet, it fits snug into the groove on the top of the mount. ... Credit to my wife for the design!

It works with the bracket from the Waggster mod. Print instructionsCategory: 3D Printer Parts Summary I couldn't find a BLTouch mount that worked with Chanh Phuong's excellent fan duct for the Artillery BMG mod, so rolled my own. ...It works with the...

The Ncase ITX Portable Monitor Mount Mod is a 3D printed accessory that allows users to attach a portable monitor to their ITX Ncase with ease. Using zip ties and existing case holes, it provides a secure and simple installation process. This mod...

Here is a slightly modified Z-Mount remix designed specifically for my customized TAZRantula, which is based on the Tevo Tarantula duel kit mod. ...This remix can be used with either single or dual Z-stepper motors/rods and requires an extended version...

Remix of https://www.thingiverse.com/thing:3294512 back cover. To be used with https://www.thingiverse.com/thing:3714121 - Link Mod.STL I needed a Pi camera mount that linked into the Link Mod to mount to my Anycubic Vyper. ...This can be used with any...

I created a simple ball mount that allows for universal mounting of the Incipio Moto Mod to any flat surface, and it comes with a vent mount clamp. I've successfully printed it using both ABS plastic and resin on my Photon 3D printer, and it works...

Eryone Thinker PS Rear Mount Mod: BOM: 4 X (M4 10, M4 T-slot, M4 Washer), you might have to use two washers if it's not tight enough. ... When it's done properly, it should have about 10mm to the moving build bed, and 30mm to the right stepping motor.

I utilized DKDaigle's V2 rail mod parts on my tronxy X5S and crafted an adapter plate to enable direct drive setup using the tank (https://www.thingiverse.com/thing:3080548). Thus far, it functions exceptionally well. ...The mounting plate employs 2 M5...

I'm using the CR-10 fan mod for a while I like the simplificy, but some days ago I received a dial gauge I wanna to use and wasnt compatible with this mount https://www.thingiverse.com/thing:2412647. ...So I remixed

Mod

mod

I needed to tweak my bltouch mount after installing the OEM Fang mod on my CR-10S. Deciding to create an updated version of one of the most widely used bltouch mounts, I opted for a significant overhaul. Eliminating the cable path was a priority, and...

This will allow the mount to sit directly behind the centre of the lens. It will also hold the Mic Mod. This is simply a slip-in fit and it holds it without the need for any fixtures. Print it in something robust like PETG or ABS. ...I printed one in...

... plate to allow me to use the tank (https://www.thingiverse.com/thing:3080548) direct drive setup on it. ...So far it works great. The mounting plate uses 2 M5 nyloc nuts with 2 low profile M5x12 screws to mount the tank. Category: 3D Printer Parts

I designed this mount specifically for making the popular Taranis antenna mod on my Spektrum DX6. I fabricated the components in black PLA with supports enabled only for the SMA_Holder, as the other parts did not require any support. Additional...

E3D Titan Aero Mount for A8 AM8 Mod. XCR3D Printer Parts include a Titan Aero HeatSink, aluminum Cooling block V6 titan Extruder Short Range Hotend. https://www.aliexpress.com/item/4000008905489.html?spm=a2g0s.9042311.0.0.57844c4dd7o6ae XCR3D Titan...

The battery holder will be mounted on the backplate and the backplate will slide into the guides provided on the camera cage. ...This is currently the first draft of the backplate and the .3mf and .f3d files are also added if you would like to play...

Rather than changing to a HeroMe setup I decided to mod the design to attach to the right hand side bed level mount point of the Bullseye. Use the carriage from the original design with the mount provided here. ... I'm still awaiting some of the parts...