evolv dna 250c box mod mount 3d models

After upgrading my printer to the Prusa Mini/+ stand mod I no longer had the ability to use my Wyze cam mount as it hooked in to the extrusion. This mount slides in to the decorative piece in the front left leg. I did this basically because I had...

After upgrading my printer to the Prusa Mini/+ stand mod I no longer had the ability to use my Wyze cam mount as it hooked in to the extrusion. This mount slides in to the decorative piece in the front left leg. I did this basically because I had...

Laserhalterung für den MK4 Mod Halterung wird mittels Magnete von der alten Laserhalterung befestigt

This is a custom modification of Spotone's ABL mount for the Ender3/CR-10 to accommodate the CR-10 hanging fan mod for MicroSwiss and E3D hotends. The mount is designed specifically for an 18mm proximity sensor. For reference, please visit:...

Three screws from a Honda vehicle - each measuring 4.5mm in diameter and 16mm long - were used to attach the mount securely. Only two machine screws, precisely 3mm in diameter and 11.5mm long, were required to affix the actual license plate. When...

I took the original(https://www.thingiverse.com/thing:4395234) and reworked the right fan mount to free up a few more mm of space so that this fan duct would fit in. (https://www.thingiverse.com/thing:3177327) I also filleted many of the edges to...

With this fan mount and a 50/15 blower fan attached, it will bring the internal temperature up to about 48c which is proper for drying PLA and maintaining other filaments. Just tap into the 24v power supply and your good to go. There are lots of...

This is part of my CR10S conversion to stand alone- see the control box page for more detail.The mount is compatible with both the stock PSU and the Meanwell PSU that I upgraded this too (and other PSUs as well, provided they use the same hole...

I used the right side handle as the mount and inserted longer screws, making it easy to remove the mod and restore the system to its original state. This design utilizes an existing filament roller design found on Thingiverse...

This adapter is designed to make your antenna mod look like a stock installation, and it's an anti-rotation, flush mount model. If you're not familiar with the process or don't have the right tools, be aware that case modification can be a bit...

Optic mount designed specifically for my Springfield XD Mod.2 (it's possible that it could fit other models as well, but I haven't had a chance to verify). The mount attaches securely to the rail located at the front of the gun, providing an...

-DNA.

Modified holder for the Cloudray laserhead to use on the ReplicantFX mod of the K40 https://www.thingiverse.com/thing:3401855

A precision-crafted support system designed specifically to accommodate the unique requirements of the Haribo mod, engineered to provide a stable and secure platform for optimal performance.

Qidi Handle Mount.stl - 1hr 20 min at 0.3mm, 15% infill using Grid Qidi Plate.stl - 2 hrs at 0.3mm, 50% infill using Grid, with 2 Extra Infill Wall Count Upright.stl - 1 hr 10 min at 0.3mm, 50% infill using Cubic Subdivision, with 3 Extra Infill Wall...

el mod tiene opciones modulares para poder usar direct drive bmg y los ductos se pueden ajustar a la altura necesaria facilmente el cuerpo se ajusta con los tornillos del disipador del hotend por lo que que es compatible con cualquier maquina con...

el mod tiene opciones modulares para poder usar direct drive bmg y los ductos se pueden ajustar a la altura necesaria facilmente el cuerpo se ajusta con los tornillos del disipador del hotend por lo que que es compatible con cualquier maquina con...

I've constructed a self-sufficient Parallel Mod Box that vapes exceptionally well. A Serpent SSM atomizer serves me well, and I opted out of the charging module due to spatial constraints in my design. The wires were soldered together, and the...

This is because (i) not all PTFE are manufactured the same (ii) your printer's 250C might be off. The effect is that there could be some ‘burnt’ or "carbon deposits" at the end of the PTFE. If you see a burnt/or carbon deposit - cut 10mm away...

According to tutorial by Lokster -> http://lokspace.eu/anet-a8-3d-printer-laser-engraver-mod/. https://3dprint.wiki - place where I found link to tut + some other useful stuff regarding Anet A8. Feel free to print or remix and don't forget to post...

With this mod, overall hotend length should be only 0.5mm shorter than that of the dragon. Or just buy this I guess https://aliexpi.com/U4Yq . ... What you need (M3): Hacksaw Sandpaper 2,5mm drill bit Straight flute M3 tap What you need...

I tried the originaal but had to much lateral movement on motor when printing with PETG, Ive modded original thoughtfully provided by author and added 2 fillets to improve motor stability, This helped a lot. I Found that i needed to fit washers to...

Add on for -> https://www.thingiverse.com/thing:3329746 According to tutorial by Lokster -> http://lokspace.eu/anet-a8-3d-printer-laser-engraver-mod/ https://3dprint.wiki - place where I found link to tut + some other useful stuff regarding Anet A8...

e3dv6 mount for 2 40x40x10 snail coolers and standard 30x30x10 coldend cooler

Remix https://www.thingiverse.com/thing:248900Added mounting holes for cable ties

e3dv6 mount for 2 40x40x10 snail coolers and standard 30x30x10 coldend cooler

... by the extruder assembly. ... This piece should seamlessly integrate onto existing components, as I simply attached the Wyze camera mount to the top, where the original camera mount was situated. ...No adjustments were made to any connecting parts.

... the extruder assembly. ... This piece fits onto the existing portions perfectly because I simply attached the Wyze camera mount to the top, right where the original camera mount was located. ...I didn't make any adjustments to where the pieces connect.

In the updated version 1.2 of the APM mount, changes were proposed by R_Lefebvre at diydrones.com.

I installed a stabilizer mount on the bow side, attaching it to the quiver's existing mounting point, which can be found at Thingiverse under #2505865. ...Be aware that you might have to lightly sand the area if the new mount is too snug.