external gpu for raspberry pi 4 3d models

I quickly edited my previous design for RPI 4 Original model is here : https://www.thingiverse.com/thing:4579831

This is a remix of Sparrows89's Gamecube Pi Classic and TheJeffChen's Logo Dunk Corner Stand.I've previously remixed this case for the RPI3B and decided that I wanted to make it for my RPI4B, too - and while remodeling it to fit the 4B, I also fixed...

This is a remix of Sparrows89's Gamecube Pi Classic ( https://www.myminifactory.com/object/3d-print-gamecube-pi-classic-45314 ) and TheJeffChen's Logo Dunk Corner Stand. I've previously remixed this case for the RPI3B and decided that I wanted to...

A duct routes the wires to the Pi GPIO pins for connection up. I only use +5 and Gnd, but anyone wanting PWM control or RPM monitoring should consider the GPIO voltage limits. This clip-on clamps pretty tight and only makes things a little bigger. I...

This adapter is designed to fit on top of the MKS 1.4 board and will require 20mm longer screws for secure mounting. ...To assemble, you will need the following parts: * 4x Longer screws than your previous MKS Gen 1.4 mount * 4x M2.5 bolts * 4x M2.5...

It is a simple and easy to print case for RPi 4 with a capability to install a 40x40x10mm fan, which is just snapped onto the top part of the case. GPIO slot can be covered with a simple insert, that partially hides the cable mess. Only screws,...

I had to find a solution to securely attach my Raspi-4 to its armor case heatsink. ...The fit was snug, far from ideal, but this approach worked adequately for my purposes in building a NAS enclosure.

You can easily install a 4-channel relay module anywhere.

This versatile combo cabinet is designed to house both MKS 1.4 and RPI for Octoprint, making it an all-in-one solution for your 3D printing needs. Please note that cables must be attached before inserting the MKS board into the front panel. ...The build...

This comprehensive all-in-one combo cabinet seamlessly integrates MKS 1.4 and RPI for Octoprint functionality. Important Note: Before inserting the MKS board inside, please ensure cables are securely attached. Key Features: * Print upside down...

... to be rotated on the face to print best. How I Designed This =================== Design was built using Windows 10 3D-Builder, so unfortunately I don't have anything to make modification easier for others for this project. ... Category: Computer

This safe setup holds it away from the plate edges, preventing vibration wear and neatly routing the cable to the rear of the Taz where I have my Pi installed. Print flat on the plate with any filament you prefer but I suggest using high-temperature...

This is a Hex version of the magnetic clip or stand for the cases. Printing this piece is successful when using an ooze shield. There is a small sprocket that holds 4 [1/2" x 1/16"] D81 Magnets (K&J Magnets). The sprocket or magnet frame slides...

this is a minor remix of BaudlerArtDesign's Rpi 4 case found here : https://www.thingiverse.com/thing:1815268 This resdesign was made to help with exhaust airflow slightly, along with adding rail mounts to the bottom shell to mount it on the left...

- "Blind" remix for RPi4 (didn't test, yet). ... - "Blind" remix for 80mm fan (didn't test it as well).

... so I basically pulled the geometry out of sneaks' slotted lid, and boolean'd it onto the two fan lids. Please refer to [thing:4650578](https://www.thingiverse.com/thing:4650578) for printing instructions, there is fairly specific settings for lids.

... in addition to a fan, so I basically pulled the geometry out of sneaks' slotted lid, and boolean'd it onto the two fan lids. Please refer to thing:4650578 for printing instructions, there is fairly specific settings for lids. ... Category: Computer

Hardware needed: 2x M3 bolts and nuts for the joints 2x M2 bolts and nuts for mounting the case 1x M3 bolt for the set screw In my experience it has been holding fine without the set screw in place, but It can really make sure that it will not move...

"Blind" remix for RPi4 (didn't test, yet). "Blind" remix for 80mm fan (didn't test it as well). ... Print Settings Printer Brand: Creality Printer: Ender 3 Pro Rafts: No Supports: No Resolution: 0.24 Infill: Various Filament: Various PETG Various ...

This front vented modular fan insert was designed to create more clearance between the processor and the fan for anyone using heatsinks. ... This design allows for about 1/2 inch of space between the board and the bottom of the fan.

Work in progress. ... Made a remix of my favorite RPi case to fit a 5 inch 800x480 DSI display (DFRobot DFR0550). Not the best remix, but it works for me. ...

Remixed Malolo's top case to fit the stock PoE hat with stock fan. ...The internal pegs have been shaved, and there's a fan cutout on the top. It needs more fiddling but it's close enough for me.

Designed up this dealer button to use in home games or have just as something laying around for any poker fan. It was inspired by a dealer button in Pokerstars VR. Printing: Ring - Infil to add weight, supports needed for spade inset. Letter...

Under the table mount for the RPi4 armor case. I used PLA 870 but PLA should also work. It is a remix of the one made by Werebear93. ...This one enable you to mount the RPI4 armor case under a table.

... room to remove the SD card easily and connect cables directly to the GPIO, plus there was a 40mm fan in the way. ...I opted for the Nocua NF-A4x10 fan, which is so quiet you can leave it on all the time without worrying about power consumption.

... lets you access the button and you can insert a 1.75mm piece of clear filament to extend the RGB LED. I modded the Case to accommodate for the shim. You still need to print a bottom of the original case to complete it. ... Category: Electronics

So, I removed the studs and countersunk 2.5mm holes for use with M3 screws. I have not tested this, but I don't see why it wouldn't work this time around. I ended up having to just cut the studs off of my printed model and then I wedged a piece of...

- The clip has been adjusted for a snugger fit. - The bottom part has been modified to accommodate more rubber foot diameters and better fit with the clip. If you have any questions, feel free to reach out or leave a comment anytime. - Printing the...

CANAKIT Raspberry Pi 4 cover for display and camera cables. See: https://www.canakit.com/raspberry-pi-4-case.html This object was made in Tinkercad. ...Edit it online https://www.tinkercad.com/things/bGTcwmjpL1D

The Canakit Case for Raspberry Pi 4 is specifically designed to facilitate the creation and advancement of more complex projects.