fan duct for noctua nh d15 in combination w tall memory modules 3d models

Fan Duct for PrintRite DIY 3D Printer I'm proud to share my updated version: http://thingiverse.com/thing:1012778 The updated duct now boasts a significantly larger tube from the fan mount to the corner. To add to that, I've also developed a third...

Este es un remix de Este modelo https://www.printables.com/model/430053-franzoli-direct-drive-ender-3-pro/comments Me encanto cuando lo vi, pero he tenido el problema de que el extrusor no encajaba, quedaba muy arriba, no se si lo hice mal yo o no es...

Human: [IT] VENTILATION CHANNEL FOR THE EXTRUDER of the CTC DIY clone Prusa i3 [EN] FAN DUCT for CTC DIY clone Prusa i3 Basic parameters: Layer height "0.2" Shell thickness "1.2" Bottom/Top thickness "1.2" Fill Density "15%" Support type "Touching...

Sorry for my bad English. ...My hotend was overheating and the heat was getting to peek, it was the abs melting inside peek and disturbing my impression. I drew this fan duct coolers for 40mm. ...I used zip tie to hold the peek

... presented a thumb screw to replace the wing nut on the front-left corner of the BIBO bed. ... It is too wide for the other two positions. I have created a smaller version to fit the right-front corner and the back-center. ... A M3-.50 nut is required.

... prints, consider installing a 120mm ventilation system. ... A support is required for the "cover". ... Plan to use eight 4mm wood screws: https://www.leroymerlin.fr/v3/p/produits/lot-de-300-vis-acier-tete-fraisee-standers-diam-3-5-mm-x-l-16-mm-e123554

This is made to specifically work with BoothyBoothy's (https://www.thingiverse.com/BoothyBoothy) amazing Hydra Fan Duct (https://www.thingiverse.com/thing:4062242) on an Ender 3 using a stock hot end. This remix has lengthened the part so the...

... 24-volt system. If you wish to upgrade to the Noctua fan, you'll need to install a voltage regulator (aka buck converter) in-line with the fan in order to step the voltage down from 24 volts to 12 volts. ... I personally suggest the Valefod LM2596.

After upgrading to the Micro Swiss nozzle, most fan ducts I discovered on this site were either too thick or required swapping out the stock metal fan case with some less stable plastic alternative. I designed a new fan duct from scratch that can...

I recently created a fan duct for my ADIMLab Gantry-S. It has been functioning properly, and as expected, I had to modify it slightly by cutting out some parts so the wires could be routed through without any obstructions. ... Best regards, SX3D

I've finally found what I've been searching for everywhere. ...Many thanks go out to Jeffrey W. Krause for creating these amazing resources, available at https://sites.google.com/site/drjeffreywkrause/diatom-models.

Easy two print parts, and glue it together with the best model glue available, UHU Hart especially suitable for gluing ABS.

... The holes for the 50mm fan are carefully designed to accommodate regular M4x20 screws without requiring nuts. The fan duct fits seamlessly into place where the original 4015 fan was mounted, making it easy to secure with the four original M2 screws.

This is a redesigned fan duct for Anet A8 printers and others that share its design. After swapping out the PTFE tube, I found it difficult to set it at an optimal height, resulting in air flowing towards the nozzle instead of the layer. To correct...

I'm an American businessman in my mid-40s, living in California, I started a startup when I was just 21 and now I've had success on two separate occasions - once by being part of something from the beginning that made billions, then after I left my...

You'll need a BLTouch and some knowledge on how to change the Firmware: https://www.antclabs.com/bltouch I used @DinkyMods' BIBO 50mm Blower Fan Mount & Duct (https://www.thingiverse.com/thing:2638477) as a base by reworking it in Fusion 360. The...

If you employ this fan duct and believe it enhances your prints' appearance designed to direct airflow precisely below the nozzle's tip.

Consequently, I took precise measurements and re-modeled the entire extruder setup on my printers, leveraging firesped's primary concept as a foundation to rebuild it from scratch in Fusion 360 with adequate clearance and recessed slots for the nuts....

I create a modified version of the original fan duct design by shadewind found at https://www.thingiverse.com/thing:3985383. I add a simple vane to enhance airflow, resulting in a noticeable improvement compared to the original. While not optimized...

Additionally, I decided to eliminate the use of the bottom screw to secure the fan duct. Instead, you'll be using the two side mounting screws on the hotend. Unfortunately, I recently sold my trusty JGAurora A5, which had been my go-to printer for...

This is a custom printed cooling fan duct designed for the Geeetech I3 Pro W wooden version, which originally does not come with one. I created this design because no suitable option was available specifically for this type of printer. The duct is...

... out the L-angle pin header. This product utilizes the results of Mr. Nao. Thank him. This product is designed assuming Proto Module with Extension & Bus Socket of M5Stack. - https://shop.m5stack.com/collections/m5-module/products/proto-module

This is a replacement air intake system designed specifically for high-performance 60mm axial flow fans. The duct is fabricated from sturdy materials to provide optimal airflow and support, ensuring that your cooling system operates at peak...

Custom-Built BPS Mount Specifically Designed to Accommodate 15mm Linear Bearings with a Distance of 30mm between Axial Housings for Secure Installation and Efficient Operations.

ENG:I made this cover for a Noctua 60x25mm fan that I installed on the power supply of my Ender 3 MAXYou need 6 screws to install it. 2 you use to fix the fan to the PSU (from the inside). 4 to fix the cover to the fanTo power the fan, I plugged it...

This is a reimagined version (and combined with a couple of other designs) tailored specifically for the ROBO 3D R1+ featuring its stock All Metal Hot End. Everyone's been heading towards the E3D v6, but my trusty stock all metal hot end has been...

This is an Electronics front enclosure for Ender 3 V2, it is designed to fit: Bigtreetech SKR 2 Raspberry Pi Zero 2 1x Noctua Fan 92x10 Needs the feet extensions already installed. For specific to the parts I had available and the limited length...

Hot end cover meant to allow for a Noctua NF-A4x10 FLX 12v fan in the hot end, and a down-firing LED strip (3x). Designed to work with - https://www.thingiverse.com/thing:4717877 Bill of Materials - Notcua NF-A4x10 FLX -...

This is an adapter for using a Noctua 4040 fan in a duct made for 5015. The current design fits on the Blokhead 5015 duct. ... Doesn't match airflow at all but it works for PETG for me.

This fan duct may not be my finest creation, but it's for my personalized 3D printer. You'll find STL, STEP, and original IPT files included. ...The part prints flat, with vents facing down towards the platform.