fan duct for noctua nh d15 in combination w tall memory modules 3d models

This is a fan mod for a noctua A12x25, for Major Hardware to use on his youtube channel for his Fan Showdown series. I have not tested this part, I don't have a printer. I'm just designing it for fun. ... If you use this thing, lmk, would love to...

The cooling fan location has been raised and moved closer towards the back of the control board for better cooling of all heat sinks, and the fan cover fits for a Noctua 40x40x20mm fan upgrade, that will not touch the Pin 27 / EZOut board upgrade. ...

So I have made one. It is not the smallest one or the fanciest case, but it is easy to print and there is possible to mount 40x10 fan (I am using Noctua NF-A4x10) so temperature can be significantly lowered (from 60+ C to cca 35C in my case - see...

The USB memory has been designed based on USB 2.0 specifications and features a UV-wrapped model. Individual components are merged together, albeit separately loose parts. ...Each section is assigned appropriate materials accordingly.

This lid is designed specifically for Razer35's remix of the 3D Cooling Fan Duct, available at https://www.thingiverse.com/thing:2334407. I'm a huge fan of that mod and have successfully modified my fan to K-FAN in the board, giving me control over...

My solution was to create an entirely new lid for the LRS-350, adding 15mm height to the psu, and purchasing a Noctua A9x14 (http://a.co/d/f3x2WTX) 92x14mm fan. This keeps the whole unit shorter than the NES-350 while remaining cheaper and more...

Installed a Noctua fan in my Xbox slim mod but needed to modify this piece to fit correctly. ... It is a nice tight fit but you may (or may not) have to shave a little plastic off to ensure the locking teeth grip properly.

Installed a Noctua fan in my Xbox slim mod but needed to modify this piece to fit correctly. ... It is a nice tight fit but you may (or may not) have to shave a little plastic off to ensure the locking teeth grip properly.

This is an Electronics front enclosure for Ender 3 V2, it is designed to fit: Bigtreetech SKR 2 Raspberry Pi Zero 2 1x Noctua Fan 92x10 Needs the feet extensions already installed. For specific to the parts I had available and the limited length...

For proper flow out of the Ring Director, I recommend only using the Dual Fan Core and Main Body.It was designed using these parts in mind (Names pulled from Amazon):-Noctua NF-F12 iPPC-CRJ Full Speed 12V Voltage Step-Up USB to Dual 3-Pin and 4-Pin...

I'm working with a model featuring a fang design equipped with a 40mm fan and a BL touch mount. The part where the BL touch attaches shows some minor damage, yet it continues to print flawlessly and exhibits impressive strength. ...It's currently...

Once the 5015 fan is wired and substituted for the stock fan, the whole assembly is designed to use the geometry of the existing extruder nozzle shroud to snap into place firmly, creating a secure and leak-free connection. Note that this upgrade is...

This adapter allows a 40mm Noctua fan to fit instead of the standard 30mm fan included with the MPMD. It's positioned close to interfering with the arms, so it's been raised and tilted accordingly.\r\n\r\nAll previous STLs that I created are...

Here is a reworded version of that statement: Cools 3D prints effectively with a 40mm fan, effortlessly printed in one piece using a reliable 0.2mm layer thickness without any support structures getting in the way.

Mount a cooler on the hotend, using a 50mm fan and a 360-degree part cooling system! The mounting holes are M5 and spaced 25mm apart, center-to-center. ... This assembly stands 80mm tall.

I originally used the stepper driver fan duct by mbrady6 but the 5015 made the entire back panel resonate. This remix solves the problem by allowing a 40mm fan to be used to cool the stepper drivers. Simply bolt the two pieces together and then bolt...

I angled the fan mount 30° from vertical and instead of clipping the duct onto the heatsink I decided to make a clamp type mount. The self tapping screws I use are 3mm x 9mm long. ... I can say that the flow through the heatsink is better and blow-back...

This is a V6 heatsink cooling fan assembly designed for mounting 5015 centrifugal/radial fans horizontally. Secure the fan to the shroud using a screw and snap the shroud onto the heatsink in place. ...Print with or without supports; bridging worked...

Cr10s Pro bracket for Noctua fans. The air is transported into the housing from outside. ... One with and one without a threaded insert, for mounting the M3 housing.

Cr10s Pro bracket for Noctua fans. The air is transported into the housing from outside. ... One with and one without a threaded insert, for mounting the M3 housing.

Once all the parts are assembled, place the fan in position and screw it lightly with nuts to fit (cables facing the side with the holder channel). The entire assembly can be easily removed from the bottom or slid out from the front of the printer...

A sturdy fan cover for a Noctua NF-A6x25 60mm fan. ... Posts are 6mm tall to prevent noise.

Monoprice Select Mini - MPSM - Revo Hot End Mount w/ 30mm Hotend - Part Cooling Fan Duct.Designed for E3D RapidChange Revo Micro Hotend Kit to be used on Monoprice Select Mini - MPSM.

The better airflow can reduce your CPU temperatures by 10-15°C.Right now it is printed in ASA and CPU reaches 48°C normal browser use. If your case reaches high temps i suggest printing in PETG, ASA or ABS.More details follow after benchmarking,...

... ... It can also apply to Tycoon/Tycoon Max, and can be used with the DIY extruder cover(thing: https://www.thingiverse.com/thing:5144461). You also need to remove the hotend cooling fan and install it above the fan duct, as shown in the 3rd picture.

... of two joined parts, glued together. ...It connects to the provided 30mm fan, ensuring effective cooling for 3D-printed objects. ...This accessory was produced using PLA on a newly assembled Rostock printer, with Cura slicing and Repetier host control.

My fifth (and continually evolving) design for a fan duct for the PrintRite DIY 3D Printer. Includes adapters for either a 60mm fan or a 70x20mm blower. This design fits completely within the outline of the extruder carriage and extends below the...

Fanduct designed for versatile use in any 3D Printer. Its unique air flow design allows for optimal cooling results. You can easily install bolts of 3mm directly into the fanduct. With this fan duct, I achieved impressive results like those showcased...

I've yet to see a part cooling fan for the sprite extruder that does not completely block your view from the nozzle so I went ahead and created a design with the fan is mounted on the side of the print head. ... I included the F3D file in hopes that...

Fan grille for 50mm fan andE3D V6 Fan Duct for 50mm Fan V2https://www.thingiverse.com/thing:4662850Height:3.5mm40mm fan grille coming soonPrint SettingsPrinter:Own BuildRafts: NoSupports: NoResolution:  0.2Infill: 35%Filament: Generic ABS...