filament splicer tool 3d models

Hingeless version is now as good as I can get it. ... It seems to print a little differently every time, so I can't vouch for other printers, but my Snapmaker seems to have the right balance of clamp grip-to-gap that keeps the clamps tight, but doesn't...

 Splicer for filament 3mm and 1.7 mm 

The hole in the tool without the ptfe cutout is 1.80mm, so it should allow filament to pass through the extruder without much, if any, trimming. If you print this tool in PETG you can also use acetone to join pieces of ABS or PLA. 2/21/2021 - I...

After printing and using trustfm's filament splicer joiner with moderate success I decided to see if I couldn't improve on a splicer so that I could get consistent repeatable splices. I used mdkendall's Parallel Jaw Pliers as a base for the design.

This is a modified filament splicer by DR2D on Thingverse. Having done fiber optic splicing in the past the biggest issue I have with melding is squared ends. This modification adds the ability to square each filament end prior to joining. While DR2D...

mold melted filament into the desired shape and size. ...use supports everywhere to obtain best outcome.</p>

Sandpaper and file to fit. ...Add grease to track. Parts must slide without side or up/down movement to keep filament centered. Heat with flame or soldering iron. ...Let cool and cut off the excess around the welded joint.

Holding jig remixed to utilize hex shapes bores and filament holding slots to avoid printing with supports and achieve better tolerances. Screw the guide bottom plate to a board. Use a piece of 3/16" dowel or short dowel pins for the hinge pins....

VARIOUS FILAMENT SPLICER CONCEPTS TO FUSE FILAMENT ENDS TOGETHER AND REMOVE THE FLASHING RESULTING.

A filament splicer that i designed that uses heat from a candle to splice your filaments.

This is a remix from RoboHart's VIT SPORT Filament Splicer. ...(https://www.thingiverse.com/thing:5233832) The files are all original but I have corrected the size.

Quite a lot of work went into it actually, we tried to make fully automated splicer first but it failed due to filament expansion issues. So manual labor is still the king :)  On the filament sample snapshot you can see results, 1 is manual and 2 is...

Actually quite a lot of work went into it this 'little thing', we tried to make fully automated splicer first but it failed due several issues such as filament expansion / shrinkage. So manual labor is still the king :) On the filament sample...

It is a rework of TrustFm's "Filament Splicer Joiner": https://www.thingiverse.com/thing:977156/#files The head of the TrustFm's FSJ was used and placed in a C bracket. Make sure to have some M3 nuts and bolts. The two photos above show the...

Part of the New Jersey Governor STEM Scholars project, our team sought to make a 3D filament splicer: Website: https://www.filamentsplicer.com/home The first file is the fusion360 file for ease of use, especially for those in schools and university...

shoulda stayed in school..] ,,,,,, I was not happy with the usual filament splicers. They are not easy to build and results are not great. But there was something in the back of my mind... Ideally, to splice filament you wanna heat only a small...

... ***************** Use: Fold in the spacer, push the two filament holders together, insert the filament until it stops, preferably warm it up first and pull it straight, and then fold it. Open the spacer again and press the button for a few seconds.

This Splicer tool is an improvement on my previous version and is now more portable and capable of splicing long lengths of 3mm PLA filament. Instructions My first attempt at a filament splicer (http://www.thingiverse.com/thing:14438) worked after a...

I looked for a filament splicer “thingi” without finding much. So I knocked this one up. Surprisingly - it seems to work! It’s based on having a hot tongue to lick the filament ends and butt them up while they are hot and sweaty. The...

If the Mk7 only supports 1.75mm then what to do with all the 3mm! Well if someone has the time (which I don't) to actually put this concept into a form of a real working converter then go ahead. ... ...

Crude Instructional Video -> https://photos.app.goo.gl/UpAShMW58KdEe2i16 Text Instructions: 1) Cut Filament-A with a flat cut and feed it through the longer bowden tube on the splicer tool. Have it poking out about 15mm. 2) Prepare Filament-B with...

Crude Instructional Video -> https://photos.app.goo.gl/UpAShMW58KdEe2i16 Text Instructions: 1) Cut Filament-A with a flat cut and feed it through the longer bowden tube on the splicer tool. Have it poking out about 15mm. 2) Prepare Filament-B with...

Simply took DR2D's excellent design and made the holes smaller so I could use a piece of filament as a hinge pin. ...You need 2x of the [HINGE] part.

I used this guy technique (https://www.youtube.com/watch?v=gyMvT61mYPY) to join filament piece together, but I didn't have a 1.75mm teflon tube so I had to 'make' one.. Customized version of https://www.thingiverse.com/thing:133050 Created with...

https://www.printables.com/de/social/461183-dm4ds/models Thingiverse will no longer be updated - all upcoming designs, only on printables!!! _____________________________________ Youtube video: https://www.youtube.com/watch?v=6MG6wYPx3rI ...

Increases holes to allow PTFE tubing to extend between the arms.

I remixed the Design from trustfm, because his design was to wobbly in my opinion. My design looks now a bit like chopsticks but it works :D I also changed out the M3 nuts to M3 heat set inserts. And designed some caps for M3x30 hex screws. ...

Pushfitting not correct !!not yet testedNEW Boddy with 2.1mm Tube inside

When using this splicer, You must be very careful while the filament is cooling / hardening. ... Link to the splicer...

FEATURES: • Simple, strong, fast, high-quality, and accurate splicing • Fully automated with minimal human interaction • Joins leftover filaments up to 50 meters in length • Self-rewinding merged filaments onto one spool (preferably using my...