finger gauntlet 3d models

Customized version of http://www.thingiverse.com/thing:45267 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=45267

They are intentionally slightly smaller than average fingers; in order to fit, they must be heated slightly, just until the plastic is pliable (a blow-dryer should work on PLA, be warned that if you use a heat-gun you can get the plastic too hot and...

http://www.thingiverse.com/apps/customizer/run?thing_id=45267 Instructions Using the following options: Thumb_Thick = 21 Show_What = Fingers Thumb_Length = 60 Index_Finger_Length = 80 Ring_Finger_Length = 95 Knuckle_Thickness = 28 Thumb_Joint_Length...

http://www.thingiverse.com/apps/customizer/run?thing_id=45267 Instructions Using the following options: Right_or_Left = 0 Pinky_Finger_Length = 75 Thumb_Bearing = 7 Ring_Finger_Length = 95 Thumb_Metacarpal = 55 Knuckle_Width = 85 Thumb_Length = 65...

Made these finger scales for my friends nazgul gauntlets. the rest was made with foam. we wanted the fingers plastic because of the sound they would add to the movements. the pieces were heat gunned over a pvc pipe to fit as needed and riveted in...

http://www.thingiverse.com/apps/customizer/run?thing_id=45267 Instructions Using the following options: Back_Hand_Length = 75 Fist_Angle = 60 Knuckle_Thickness = 28 Right_or_Left = 0 Thumb_Joint_Length = 38 Thumb_Metacarpal = 55 Thumb_Bearing = 7...

... Heres the articulated fingers for HappyMoon's infinity gauntlet. May need some finishing work On some parts, but works great! I wore it for 10Hrs on and off at mcm London with only minor issues! ... hope to see what everyone can do with them!

http://www.thingiverse.com/apps/customizer/run?thing_id=45267 Instructions Using the following options: Thumb_Thick = 25 Thumb_Bearing = 7 Index_Finger_Length = 99 Ring_Finger_Length = 98 Knuckle_Thickness = 28 Back_Hand_Length = 94 Thumb_Metacarpal...

http://www.thingiverse.com/apps/customizer/run?thing_id=45267 Instructions Using the following options: Thumb_Metacarpal = 59 Knuckle_Thickness = 29 WT = 3 Knuckle_Width = 88 Thumb_Bearing = 9 Show_What = Fingers CRES = 20 Thumb_Thick = 21...

http://www.thingiverse.com/apps/customizer/run?thing_id=45267 Instructions Using the following options: Index_Finger_Length = 99 Show_What = Hand Fist_Angle = 60 Middle_Finger_Length = 108 Knuckle_Width = 85 Thumb_Bearing = 7 Finger_Thickness = 20...

http://www.thingiverse.com/apps/customizer/run?thing_id=45267 Instructions Using the following options: Pinky_Finger_Length = 82 CRES = 20 Thumb_Length = 75 Thumb_Thick = 25 Back_Hand_Length = 94 Finger_Thickness = 20 Fist_Angle = 60 WT = 2...

I made a full chainmail gauntlet version of the gauntlet fingers I did a while back. I'm uploading it in three parts because Thingiverse is being difficult. EDIT: I am now breaking it down into one version at a time because Thingiverse is being...

by UnsungHero https://www.thingiverse.com/thing:4241705 repositioned and rotated the finger parts to better print them in meshmixer

http://www.thingiverse.com/apps/customizer/run?thing_id=45267 Instructions Using the following options: Thumb_Thick = 24 Pinky_Finger_Length = 87 Back_Hand_Length = 90 Right_or_Left = 1 Knuckle_Width = 90 Ring_Finger_Length = 105 Thumb_Metacarpal =...

http://www.thingiverse.com/apps/customizer/run?thing_id=45267 Instructions Using the following options: Thumb_Thick = 17 Index_Finger_Length = 59 Show_What = Fingers Thumb_Length = 50 Ring_Finger_Length = 54 Knuckle_Thickness = 22 Thumb_Joint_Length...

http://www.thingiverse.com/apps/customizer/run?thing_id=45267 Instructions Using the following options: Thumb_Thick = 24 Show_What = Fingers Thumb_Length = 73 Index_Finger_Length = 105 Ring_Finger_Length = 105 Knuckle_Thickness = 30...

http://www.thingiverse.com/apps/customizer/run?thing_id=45267 Instructions Using the following options: Ring_Finger_Length = 95 Thumb_Length = 73 WT = 3 Finger_Thickness = 25 CRES = 20 Knuckle_Thickness = 35 Thumb_Thick = 25 Pinky_Finger_Length = 75...

Temporary Gauntlet upload

a bravado gauntlet from gta

https://micronote.tech/2019/09/Printed-Gauntlet/A 3D printable gauntlet.Assembly requires:- 1 inch elastic- 1/4 inch elastic- needle and thread

... ... Ideal for real-time applications. PBR textures in high resolution (4k) Works well with subdivision Single object (with separate elements) Single UVMap Detailed interior Based on authentic medieval gauntlet .obj .fbx .blend in additional files.

A stomping gauntlet made for the game Hasty Melons. It’s my first complex model as well as my first hand painted texture. ...It’s not perfect but I’m overall happy with the result.

For fun during a CADathon I started designed a laser-cut gauntlet that you could strap onto your hand. It's not as far as I'd like, and perhaps in the future I'll work more on it and try to finish it. ...I tried to make it so that the necessary lengths...

cool base blade gauntlet that can be modded for a gladiator to a post apocalyptic warrior Print Settings Printer Brand: MakerBot Printer: MakerBot Replicator Mini+ Rafts: Yes Supports: Yes Resolution: .2 mm Infill: 10% .4mm Notes: may be too big...

... cloud to hopefully remove any printing issues. I have a printer just haven't figured how to calibrate it properly yet. Added the complete Gauntlet as single wasn't showing very well but only print from single, other not run through netfabb cloub.

http://www.thingiverse.com/apps/customizer/run?thing_id=45267 Instructions Using the following options: WT = 2 Fist_Angle = 60 Right_or_Left = 0 CRES = 20 Thumb_Thick = 20 Middle_Finger_Length = 100 Thumb_Length = 67 Thumb_Bearing = 8...

Finger

finger

Finger

finger