flashforge creator 4 3d models

This instruction comes directly from the FlashForge Creator Pro 2016 manual and represents a major limitation of this printer. However, after conducting extensive testing, I discovered that this printer has the capability to utilize the right...

These precision corner pieces are designed for seamless integration with the FlashForge Creator Pro when using a glass build plate from 3DUniverse (http://shop3duniverse.com/products/glass-build-plate). There are two distinct brackets to choose from,...

These are the G-code snippets that belong with my PrusaSlicer (Slic3r) profiles for the FlashForge Creator Pro. Although I think the G-code is quite mature now, it is possible I will update it separately from the rest of the profile. Therefore use...

This directive comes directly from the FlashForge Creator Pro 2016 manual, and it's the sole drawback that I've encountered with this printer. Following extensive testing, I've confirmed that this printer has the capability to use the right extruder...

This is an alternative version of the 50mm spool holder by RonPossible, for the recent revisions of the FlashForge Creator Pro. This is suitable for filament spools with a simple cylindrical hole of 50mm diameter and 60mm length. The differences...

A replacement (or additional) bowden tube/ribbon guide for the Flashforge Adventurer 4 & Adventurer 4 Lite. Simple print, and should take less than 10 minutes to print. ... I printed this on the Adventurer 4 Lite, but that option is not availabe in the...

The 4 clips I created will exert pressure on the plate from all sides, holding it firmly in place during the print process, regardless of temperature fluctuations. Removing and reattaching the plate is also straightforward. To fit glass plates that...

This is a replica of the bracket that is part of recent editions of the FlashForge Creator Pro and similar printers with a dual MK10 nozzle carriage. It is mounted on the left side of the extruder carriage, and supports both the blower fan and the...

The spools of filament I purchased refused to seat properly on the standard spool holder supplied with my FlashForge printer, which boasts a 66mm x15mm spacer at its base. In stark contrast to the spools that came bundled with the FlashForge, the new...

I purchased a Raspberry Pi 4b 4GB for running Octopi on my FlashForge Creator Pro. Unfortunately, I couldn't find a compatible Pi4 case for my printer, so I remixed cartermultz's Pi4B+ Hex Case with dewhisna's Pi3 Sleeve Case to create this unique...

... out this wingtip M3 nut in ABS plastic, utilizing a layer thickness of 0.25mm and an infill percentage of 20%. ...This part replaces the existing knurled nuts provided with the FlashForge printer, which can be tricky to use when calibrating the hotbed.

This is a remix of https://www.thingiverse.com/thing:805717 I made some adjustments to fit the latest Creator Pro (2016+)

This would also be simple to use for my Anet A8 printer, which will sit right next to the FlashForge. I have two bins with eight Filament spools plus the two that mount behind the Printer. I mainly print in ABS, but will soon start using PLA. So the...

I'm looking to prevent the cap-head screws on my new FlashForge from sinking into the frame over time. Since the holiday weekend has me without access to a hardware store, I decided to print my own washers instead of waiting. ...These custom-made parts...

With my Flashforge, current models didn't fit very well and required modifications to enable the Extruder idler to open freely. I also wanted to simply use the included center brace to manage cables effectively. Here's my remix. I've printed and...

Add a 3mm Plate Glass Spacer to Enable Heating Bed on Flash Forge Creator X. ...A special spacer is required to activate the limit switch earlier, allowing for 3mm thick glass to be loaded.

This is an add-on to http://www.thingiverse.com/thing:735350, engineered to secure split loom (1/2" or stock Flashforge) covered wiring in place. The original design's small filler piece was deliberately omitted for this iteration. To ensure a flush...

This shim is designed for the glass products sold on this website:\nhttps://www.flashforge-eu.com/parts-and-accessories/frosted-glass-build-platform\nPrint Parameters\nMachine: \n Flashforge Creator Pro\n \n Raft Settings: \n Disabled\n \n Support...

... attach to my Creator Pro printer. In response, I've created this modified clip, hoping it will serve as a solution for anyone facing similar issues when attempting to utilize the original mounting mechanism with their own Creator Pro printers.

Extra-long spool holder for Creator Pro required due to inconsistent reel sizes among filament manufacturers. A spacer clip can be used to adjust width or print multiple clips to prevent narrower reels from falling off the spool. ...Raft-free printing...

... been using the 2016 edition of my multi-width bracket, and it turns out that's actually designed for the 2015 model. ...Because of the open clips on the v.2016 Creator, this bracket may not grip as securely as the one made for the 2015 version does.

The manual valve is to regulate the flow. ... 100% - 80% - 60% - 40% - 20% of the section screw m2 * 8 screw m2* 10 m2*10 is glued (cyano) with FF_Creator_Pro-front_dual_duct_v6.3r p.STL https://www.youtube.com/watch?v=N721BUCsqvQ

The Creator Pro arrives with a spool holder that often proves too bulky for many spools. Several innovative designs have been proposed as solutions, but some are challenging to print, necessitate assembly, or fail to accommodate spools with...

To enhance my Creator, I added a Dust Filter mounting option on it. The Bevel modification was done for increased strength and fewer breakage points. For simpler installation, the piece was divided into two parts. ...However, I think there's room for...

I love the variety of filament alignment brackets available here for the Flash Forge Creator Pro, but one persistent problem I encountered was that after a few prints, the filament tubes would simply drop through the holes of the alignment bracket to...

... into the existing cooling fan and utilizes the same screw holds. Print Settings Printer: Flash Forge Creator Pro Rafts: No Supports: Yes Resolution: 200 Micron layers Infill: 20% Notes: Print from ABS or PETG to resist heat from the extruders.

... the back plate, plus inserted slots for securing M3 nuts on the rear bracket for a tighter grasp when assembling the parts. ... Print Settings Printer: Creator Pro Rafts: Doesn't Matter Supports: Doesn't Matter Resolution: 0.20mm Infill: 40% or greater

... ABS (using 230C/110C heat settings for extruder/bed) Medium speed 20% infill Finally, hit print and you're ready to go! Here's a link to the Tinkercad model: https://www.tinkercad.com/things/5clJPy6WEL2-flashforge-plug-dual-color-with-supports

Print Settings: Printer: Flashforge Rafts: No Supports: Yes Resolution: .2 Infill: 75% Notes: It must be quite strong, so ABS or PETG supports might be necessary for the large hole (PLA cannot handle motor and hot end heat). ...This is a work in...

... following were defaults (which I kept): ABS (I use 230C/110C heat settings for extruder/bed) Medium speed 20% infill Ok, then print! Here's the Tinkercad link: https://www.tinkercad.com/things/5clJPy6WEL2-flashforge-plug-dual-color-with-supports