flashforge creator 4 3d models

A Cable Tidy-Up Guide for Rear Printer Cables.

The air duct is very simple and directs air precisely to the place of printing under the nozzle and not on the nozzle itself as in the stock, print it with a thickness of 0.1, the plastic does not matter, set it so that it does not touch the nozzle.

An OctoPi OctoPrint mount for an Aukey Webcam that fits underneath the print bed. ...This is a friction fit and may need to be slightly adjusted for your configuration.

Customized version of https://www.thingiverse.com/thing:1308210 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=1308210 Instructions Using the following settings: Outer_Diameter = 36 Ridges_Depth = 62

An OctoPi OctoPrint mount for an Aukey Webcam that fits underneath the print bed. ...This is a friction fit and may need to be slightly adjusted for your configuration.

Крепление для трубки подачи филамента. ... Расположение сбоку

Designed as universal spool holder. Print both parts without support. ... 0.2mm-0.3mm layer height 20% infill

Use a length of filament to secure the hinge pin firmly into place. ...This crucial component can either be glued in or, like my setup, held fast with double-sided adhesive, making sure it's installed when the lid is shut tightly.

Remixed for 3/8 inch dial indicator shaft. 7/22/15 Minor revision implemented. The initial hole was undersized due to printing precision issues. Instead of adjusting the STL file, which would impact other dimensions, the hole diameter was increased...

Firstly acknowledgement goes out to rowokii for creating the Spool Holder & Clip on Thingiverse, accessible at https://www.thingiverse.com/thing:767317. My goal was to gain visibility into my spools' activity, which is impossible with the standard...

I designed this in 2 pieces. The main body and the top cover. The main body allows you to organize the fan wires, and the top cover secures it all to the extruders. If your extruder fans do not have plug connectors, you will need to install them...

It's not the best scan but best I could get without spending a ton of time and removing it from the printer. ...It should have enough of all critical geometry to design an improved print head which is my goal.

The project's primary goal is to replace the dual carriage of the original model with the BIQU H2 extruder. ...The project is in progress, but it can be used already.

I installed a new fan mounting system to secure my mainboard's cooling fan in place. The old fan mount had been problematic, so I swapped it out for a sturdy replacement from Noctua, ensuring optimal airflow and efficiency. ...To print the custom fan...

I recently revised an existing concept to produce this new version. ...This revision has evolved from my prior attempt found at http://www.thingiverse.com/thing:857216, featuring upgraded internal threading in conjunction with exterior grooves for...

I've made some adjustments to the rods that fit snugly into the printer and fine-tuned a section of the filament guide. ...The issue was that my filament was causing my guiding tube to partially retract through the bracket, but now it can only go in for...

This model was crafted using Tinkercad's robust design capabilities. ...It can be easily edited and refined online at https://www.tinkercad.com/designs/hEiUfYKuyKY.

I was looking to attach my Logitech C270 webcam to the front of my printer, and I wanted a solution that would be compatible with the printer door being either open or closed. Many of the available mounts required the door to be shut in order to...

This is a performance enhancement designed to boost resilience and robustness. ...It realigns the filament guide rods, ensuring the filament unwinds with greater uniformity from its reels.

Habe einen neuen Motor gekauft und den Metal Extruder. Danach die Halterung inkl.dem Sensor Gehäuse konstruiert. Seit dem gar keine Probleme mit knackende Geräusche und das Filmend läuft super durch. Evtl. ...kleine nacharbeiten mit der Feile...

If you intend to print it, please read the following information thoroughly: This active cooling duct is designed for MakerBot Replicator 1, FF3DP FlashForge, CTC Creator Dual, and WanHao Duplicator 4 & Duplicator 4X printers. A version for...

Modification Upgrade for the Flashforge Creator Pro 2015 Spool Holder ø38x91mm Makes it Easy to Add Smaller Spools Without Fretting Over Them Falling Off Specifically Designed to Fit Sainsmart Filament Spools With Ease.

The new edition of the z-axis shim, redesigned specifically for the Flashforge Creator Pro, has emerged. I made a special addition to this latest remix: a thicker, extra strong 5mm Z-Axis Shim Version. ...Alongside that significant update, I included...

Printer Settings: - Printer Brand: FlashForge - Printer Model: Creator Pro - Rafts: No rafts needed - Supports: No supports necessary - Resolution: .2 mm layer height - Infill Density: 100% infill - Notes: Printing two sets of these brackets is...

Post-Printing This box fits on my Qidi Tech printer and should fit Flashforge Creator Pro style printers as well provided there is a gap between the sheet metal which you can utilize. The bottom of the pegs for the cover may need a little bit of...

These files install a Big Tree Tech 1.4 Turbo in a pre-2016 FlashForge Creator Pro. I don't know if this will work with the 2016 or later models. When the USB port on my board failed I felt it was time to upgrade my FFCP. I used the BTT 1.4T since I...

Print Settings Printer: Flashforge Dreamer Rafts: Yes Supports: No Resolution: Standard Infill: 20% Notes: I used ABS. My part started curling up and I had to add white school glue to keep it down, so I suggest using a raft. When it's loaded into...

I'm excited to share with you a DIY camera mount designed specifically for your Samsung Note 4 smartphone, which can be paired with an Otterbox case. The mount enables time-lapse photography capabilities when used in conjunction with FrameLapse Pro...

... use these specifications: - ABS material with a layer height of 0.2 mm. - 2-layer shell printing with 0.4 mm width layers. - Fan-mounting area must be oriented downwards. ...- Supportive features are not needed for this easy print job.

The design also eliminated the need for supports or rafts during printing.\nWorks flawlessly, offering plenty of strength.\nPrint Settings\nPrinter: Flash Forge Creator Pro\nRafts: No\nSupports: No\nResolution: .27 mm layers\nInfill:...