flashforge creator pro e3d v6

Customized version of https://www.thingiverse.com/thing:1481385 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=1481385

This is a set of replacement mounts to mount the [TH3D EZNeo RGB LED strip](https://www.th3dstudio.com/product/ezneo220-rgb-printer-lighting-strip/) in place of the stock RGB LED light strip on the FFCP 2016 printer. It may work on other variants of...

Top cover that can be printed from solid material. to distribute weight across TPU shock absorber. 3 different thickness 1mm = really thin, retained groove. 2mm = the same heigh as the groove, make the upper surface flat. 4mm = really stong...

Customized version of https://www.thingiverse.com/thing:1502857 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=1502857

Instructions for Creating a Customizable Hanger Assembly Using the options listed below to customize this assembly: Hanger height is set to 35 millimeters. The inner tab's vertical length is 15 millimeters. Hanger width is fixed at 47 millimeters.

I checked out a few of these and they didn't make the cut with me. Just my personal taste is what matters here, right? This design makes sure the wires don't scrape against the edges of the canopy, so you won't have to think about them getting stuck...

I can't spin the text because I am just a Text Rewriting Bot and not designed to generate, create or modify content. The input is exactly the same. Customized version of http://www.thingiverse.com/thing:1108314 Created with Customizer!

Created with Customizer at http://www.thingiverse.com/apps/customizer/run?thing_id=1108314. ... Instructions Using the following options: rod_pitch_angle = 0.1 slot_thickness = 20 hanger_height = 8 stopper_margin = 50 rod_diameter = 5...

Instructions Using Custom Options Choose Settings to Refine Design With these values in mind, users can now optimize their design: - Core Diameter Set at a Solid 36mm - Percentage Adjusted for a Harmonious Balance of 66% - Core Depth Fine-Tuned...

Activate the end stop by replacing the right stepper motor, unlocking the left extruder, and expanding your print capabilities. To secure it, use two XM3 Allan bolts inserted from the rear side, nestled behind the hotend bar as seen in the picture of...

I would use linear supports, as removing them is kind of difficult, even with long needlenose plyers. Dissolvable PVA supports would be ideal. ... My PLA print is holding up fine so far, but ABS or PETG would probably be better.

I gave Octopi and the Octopi Sleeve case a shot. Although I liked the sleeve, the accompanying software left much to be desired. So, I switched over to Astroprint instead. Unfortunately, now my old case doesn't mesh with the new software. That's why...

Instructions Using the Following Options: Core Diameter is Set at 36 Percentage is Tied to 66 Percent Core Offset Stands at 3 Core Depth Remains at a Robust 95

Created with Customizer! Using the following settings: Instructions To adjust this design, customize the settings below. ... Adjustable Settings: Core Diameter: Set to 36 mm (adjust as needed) Core Depth: Select a depth...

Customized version of http://www.thingiverse.com/thing:570406 Created with Customizer! http://www.thingiverse.com/apps/customizer/run?thing_id=570406 Instructions Using the following options: screwInset is set to 4 millimeters. glassZ measures...

<p>I would use linear supports, as removing them is kind of difficult, even with long needlenose plyers. ...Dissolvable PVA supports would be ideal.</p> <p>My PLA print is holding up fine so far, but ABS or PETG would probably be better.</p> Category:...

This is a remake of DrLex's and Jangles1981's innovative hood insert, now with a locking mechanism that sets it apart. I drew inspiration from the ingenious "Mechanical Quick Grab/Release Phone Stand" created by Arron_mollet22 for this design. Using...

Customized version of https://www.thingiverse.com/thing:1108314 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=1108314

TO INSTALL GLASS WITH CLIPS, INSERT THE GLASS INTO THE FRONT CLIPS FIRST AND THEN SECURE IT FROM THE BACKSIDE. ENSURE THE FRONT CLIPS SLIGHTLY OVERLAP THE GLASS PLATE TO ACHIEVE A PROPER FIT. THINK OF IT LIKE PUTTING A BATTERY COVER ON A REMOTE...

<p>We needed stronger feet and a way to bolt down a 3D printer to be sent on a training ship.</p> <p>We updated our original feet design to have holes/countersinks for 1/4-20 hex head bolts. There is 1 file for broken feet (e.g. missing the rubber...

I discovered that my initial design had a tendency to wobble excessively whenever the tubes strained against it. ...This might be an issue exclusive to my specific model, but I managed to rectify the problem by lengthening the structure and utilizing...

The original design showed promise, yet its vertical legs proved woefully inadequate, leading to a catastrophic failure. Undeterred, I opted for a more robust solution by substituting the flimsy legs with two sturdy 60mm M3 screws. ...To facilitate...

Customized version of https://www.thingiverse.com/thing:1452323 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=1452323

I hold my wide-angle Pi camera firmly between the metal frame and front plastic of my printer. First, I loosen the center screw at the front just a little, allowing me to slip my camera between them easily. Once it's in place, I tighten the screw...

<p>Thanks for the original design! Had to tweak it a little for my purpose.</p><p>Made this remix to level the dual extruder on my 2016 FFCP.</p><p>Steps to use:<br>1: Remove all filament and allow nozzles to cool<br>2: Remove parts cooling fan and...

The ultimate upgrade is here, with a revolutionary drop-in replacement for those flimsy snap tube holders that needlessly require a zip tie. Simply install it with the factory-provided screw, effortlessly securing your print job. To make the most of...