flashforge finder mods 3d models

This is a minimal mount intended for installing a Raspberry Pi inside a FlashForge Creator Pro or similar printers, but of course it can be used for any other application where a Pi needs to be mounted without the need for a case. I created the...

Print Settings Printer: FlashForge Creator X Rafts: Doesn't Matter Supports: No Resolution: .2mm Infill: 10% Refer to the notes below for helpful printing and assembly instructions. Building the Model Colors (there are no multiple printed pieces) ...

Printing Settings All components for this design were printed on a Flashforge Dreamer with Hatchbox PLA. The majority of the components are designed for minimal supports, but some require supports. Recommended print orientation and support locations...

Also the parts were dimensioned to the maximum printable size of Flashforge Creator 2 that is a small volume printer, so should be no problem to print in other equipment. Our model was printed in ASA, using 0.15 mm layer and 20% infill to give...

Print Settings Printer: FlashForge Creator X Rafts: Doesn't Matter Supports: No Resolution: .2mm Infill: 10% Building the model Colors (there are no multiple printed pieces) Black: eye_blacks (contains two pieces) eyebrow_left eyebrow_right mouth .....

... frequently. Let me know if any are down and I will try to update them with current compatible parts. Print Settings Printer Brand: FlashForge Printer: Guider II Rafts: Doesn't Matter Supports: Yes Resolution: 0.2mm Infill: 20 Category: Tools

... <font size="+1">^Like</font> button** and turn that heart red <img src="https://cdn.thingiverse.com/site/assets/like-button-liked.svg">.                                                      

Here's a build video of Rollcage: https://youtu.be/YQmMvlJW1rw Print Settings: Printer: Flashforge Dreamer Rafts: No Supports: Yes Resolution: 0.2mm Infill: 20% Notes: Also used brim to prevent edges curling up. Designed using Sketchup and...

Subsequently, my awaited servos arrived, along with a brand-new Flashforge Creator X printer. Assembling the robot necessitated creating the base part in three separate pieces since its original size surpassed my 3D printer platform capabilities. In...

Print Settings Printer: FlashForge Creator X Rafts: No Supports: No Resolution: .2mm Infill: 100% Notes: See below for important printing instructions regarding the color. Building the Model Colors and multiple printed pieces Black: stand (two...

Print Settings Printer: FlashForge Creator X Rafts: No Supports: No Resolution: .2mm Infill: 10% Notes: See important notes in the 'extra notes for printing' section for the black eyes and whisker pieces. I printed all the parts except for the head...

... <font size="+1">^Like</font> button** and turn that heart red <img src="https://cdn.thingiverse.com/site/assets/like-button-liked.svg">.                                                          

... <font size="+1">^Like</font> button** and turn that heart red <img src="https://cdn.thingiverse.com/site/assets/like-button-liked.svg">.                                                          

Print Settings: Printer: FlashForge Creator X Rafts: Not required Supports: None needed Resolution: .2mm Infill: 10% Notes: See below for helpful printing and assembly tips. Building the Model: Colors (there are no multiple printed pieces): Light...

This is the maximum height I can print with my FlashForge Creator Pro with glass bed. There are 3 cams that have to be placed on the quarter inch rod drive shaft such that they rest directly under the push rods from the reindeer and sleigh. Each...

Print Settings Printer: FlashForge Creator X Rafts: Not necessary Supports: None required Resolution: 0.2mm Infill: 10% Notes: Check out the following helpful printing and assembly tips. Building the Model Colors (note that there are no multiple...

Print Settings: Printer: Flashforge 3D Creator Pro Resolution: .27 Infill: 15% Notes: A 15% infill should be sufficient for the bird print, but it can be increased if necessary. Post-Printing: Finished prints by user mled90 showcase the original...

More coins are added each round. Print Settings Printer Brand: FlashForge Printer: Dreamer Rafts: No Supports: No Resolution: Anything 0.4mm and below should do fine. Infill: 15-35% Filament: Any Any Contrasting Colors Recommended Notes: For...

----------------------------------Print Settings---------------------------------- Printer: FlashForge Creator X Rafts: Doesn't Matter Supports: No Resolution: .2mm Infill: 10% Notes: SEE BELOW FOR HELPFUL PRINTING AND ASSEMBLY TIPS. As with most of...

I printed this adapter using a FlashForge Creator Pro printer with the following settings: no rafts, supports enabled, and a resolution of 0.3 mm. When printing in ABS, I found that maintaining adhesion was a challenge due to the summer heat...

https://www.facebook.com/bill.binko/videos/1377778868931833/?permPage=1 This will be part of a larger Guide at the main ATMakers.org site and we will update this when it's ready. Print Settings Printer Brand: FlashForge Printer: Creator Pro Rafts:...

... <font size="+1">^Like</font> button** and turn that heart red <img src="https://cdn.thingiverse.com/site/assets/like-button-liked.svg">.                                                     

**Print Settings** **Printer:** FlashForge Creator X **Rafts:** Not necessary **Supports:** No supports required **Resolution:** 0.2mm resolution for a smooth finish **Infill:** 10% infill for added stability **Notes:** Minor supports are needed for...

FAQ: http://www.thingiverse.com/shivinteger/about [>>>] Generating Attributions log: [0] Thing Title: Filament Spool Winder for LYMAN [0] Thing URL: http://www.thingiverse.com/thing:30705 [0] Thing Author: hlyman [0] Thing Licence: Attribution...

I printed everything at "High" on a Flashforge clone of the original Replicator Dual in ABS, except the D-Ring jig. I used a raft, but no supports as the design was meant to print well without them. I batched several components together and it took...

Print Settings Printer Brand: FlashForge Printer: Creator Pro Rafts: No Supports: Doesn't Matter Resolution: 0.1 mm Infill: 100% Notes: 100% infill will result in a heavier and longer-lasting spinner. For the same reason, a dense filament like PETG...

... <font size="+1">^Like</font> button** and turn that heart red <img src="https://cdn.thingiverse.com/site/assets/like-button-liked.svg">.                                                          

https://3dwarehouse.sketchup.com/user.html?id=0322118571106718978163948 This model was created utilizing his 3D file of a myosin II mini filament inside of Sketchup Print Settings Printer: Flashforge 3D Creator Pro Rafts: Yes Supports: Yes...

With higher resolutions you can probably crank out a little more detail, but the difference will not be very big. Edit: Made some small performance improvements by rewriting screw thread library to use a single polyhedron. A high res version with...

... <font size="+1">^Like</font> button** and turn that heart red <img src="https://cdn.thingiverse.com/site/assets/like-button-liked.svg">.