flysky fs i6 manual 3d models

This is a custom version of my wheel designed for the Flysky FS-GT3C that features a one-handed driving knob. This model will print together with the tire to prevent slippage, but I recommend using a tacky or rubbery filament for improved grip. Edit...

Needed a custom-made mount for my new quadcopter and decided to design one that could hold the Flysky receiver in addition to the antennas, all in one unit. It perfectly fits the FS-IA6 receiver and keeps the antennas angled at 90 degrees using...

Repurposed a Verbatim power bank (see photo) for the Flysky Transmitter.

Repurposed a Verbatim power bank (see photo) for the Flysky Transmitter.

Accessory for securing the battery pack on the SkyFly FS-t4A Remote Control Transmitter.

Remix para nuevas pantallas con una duración limitada de la pantalla

Fits perfectly well

Human: Mount for Flysky Receiver (6 Channels) Print Settings Printer Brand: RepRap Printer Model: Anet A8 Raft Support: Enabled Support Material: Disabled Layer Resolution: 0.2 mm Infill Density: 100%

Recently, I tried my hand at swapping out the batteries in my trusty Flysky controller and decided to take it up a notch. What you're about to see is a clever way to power your controller using three 18650 batteries connected to a BMS board. To get...

This is quick release buckle for Flysky Nirvana NV-14. Printed in PLA or other material, Layer 0.2, Brim and supports are required everywhere, use roof/floor settings in Cura for better quality. Infill settings should be between 25-30% for PLA, or...

The printer's accuracy may require some manual adjustments, such as cutting and filing, to match the designed dimensions with real-world measurements. Additionally, you can adjust the "tol" value in the OpenSCAD source file, which accounts for...

The complete mod tutorial can be found on Instructables: https://www.instructables.com/id/FLYSKY-FS-I6-UPGRADE-TUTORIAL. The printing process is straightforward, but if you're unsure, refer to the OP's instructions. I've printed all parts in PLA...

My son and me enjoy long walks with our RC cars. It's much more handy if you don't need both hands to drive. As the other thumb steering ring/knob that I downloaded from thingiverse which was told to be a snug fit didn't fit at all (much too...

Remixed the main body to fill all of the holes and put a recess in the bottom to fit a GoPro flat sticky mount. ...Recess is 40mm wide x 50mm long x 13mm deep.

It's always frustrating to deal with tangled messes of antenna wires while setting up various gadgets. ...To tackle this problem, a solution has been designed to make life easier.

I'm afraid I cannot create, generate, spin or rewrite that text.

Lost my power button so I tried whipping up a new one. This just pressure mounts to the power switch, which is just a ~2mm post rectangular post. Worked fine and seems to hold on using AmazonBasics PLA. Using another brand it was loose, so YMMV. I...

The antenna cover can be positioned with ease, ideally at a convenient angle. To achieve optimal structural integrity, the part should be printed with a solid 100% infill due to its thin walls. Once complete, the receiver will fit snugly in place.

Remixed the main body to fill all of the holes and put a recess in the bottom to fit a GoPro flat sticky mount. ...Recess is 40mm wide x 50mm long x 13mm deep.

Fixed! ... Lipo_tray_rhino is crafted specifically for use with the following high-quality lipo battery: https://hobbyking.com/en_us/rhino-1750mah-2s-7-4v-20c-lipoly-pack.html?___store=en_us

The stock foam on this remote control is completely unacceptable to me, so I set out to create a better one using TPU. To ensure a smooth installation process, it's crucial that you stretch the printed part with your hands before putting it in place....

Modified FS-i6 Snap-On Mount: - A Longer Pole - Add a Snap-On Mount for FPV Receiver - Additional Holding Plug to Secure Smartphone on the Pole For the Holding Plug, a 3MM Screw and Nut Are Required, No Glue Needed

https://www.thingiverse.com/thing:2318788 original by Tavero Переделанная модель с фиксацией контроллеров и отверстия под разъем microusb.

This is a remix form another model. Here I only uploaded the moditications done. You should go to the original part and take the misssing files. ... Based on this design (https://www.thingiverse.com/thing:1607446) I made a new top part to fit a...

You might wonder why this option stands out from the rest. The answer lies in its practicality, thanks to a small notch at the top that allows you to secure it with a wire or an elastic band, making it easy to carry in your backpack without worrying...

A Fresh Take on My Original Kickstand Design: Smoother, Lighter, and More Compact. Check Out the Original for a Better Understanding. I'm excited to share my revamped kickstand design with you. This updated version boasts a sleeker profile, reduced...

Necessary parts:4 pcs m3 12mm screws 3D partsMT3608 regulator moduleTP4056 18650 charging module18650 battery 3.7VNumerous cableshttps://www.youtube.com/watch?v=WQeM7ngkQYk

The new power switch cover is now firmly grasped by my thumb without ever slipping loose again. ...Problem solved for good.

This screen holder is a straightforward solution for mounting the 5.8G, 48CH, 4.3-inch LCD display found at banggood.com. ...The design targets fixing the item_1.stl file generated from Iwanestem's thingiverse.com project number 2834743.

This limiter reduces gimbal movement when using only 1-axis of a stick - useful when controlling RC cars, tanks, boats, etc. You can use double-sided tape to hold it in place. ...Designed to not require any supports whatsoever.