folger tech ft 5 3d models
582960 3d models found related to folger tech ft 5.thingiverse
This is a bracket to add a reverse Bowden tube to a Folger Tech FT-5 or any other printer with 20x20 aluminum extrusion.
cults3d
This converter was designed with the intent to turn the Folger Tech FT-5 Large printer kit into a dual extrusion printer. The original parts were alter to fit heads similar to the CTC 3-D printer. The attachment will sit on the rail system of the...
thingiverse
This converter was designed with the intent to turn the Folger Tech FT-5 Large printer kit into a dual extrusion printer. The original parts were alter to fit heads similar to the CTC 3-D printer. The attachment will sit on the rail system of the...
thingiverse
Six m5 X 10 screws and m5 t-nuts required.along with a 5/16" or m8 smooth rod cut to size Print Settings Printer: Folger Tech FT-5 Resolution: any Infill: any but I went 100% Post-Printing Dependent on your calibration, you may have to clean, file or...
thingiverse
This is a tool for building the Folger Tech FT-5. It calls out to space the two upper levels 170mm apart. Had no way of doing it. My dial calipers only went to 6" or a little over 152 mm so I just made my own tool to do the job. Nice to have a 2nd 3D...
thingiverse
Printed L and T brackets from PETG (ESUN). ... Very strong and worked well. I have built a Lead Screw version of the FT-5 and used these brackets.I recently added a Corner brace for the FT-5 R2 one of mine was damaged and needed replacing
thingiverse
I took the BLTOUCH holder for the FT 2020 i3 and mated it with the cooling block spacer to make a holder for the FT-5 since there didn't seem to be one for the stock hot end. I couldn't use the one for the 2020 i3 because the cooling block doesn't...
thingiverse
This is a fan shroud for Folger Tech FT-5 printers. It uses a 5015S blower fan. ...Print Settings Rafts: No Supports: ...
thingiverse
This is a well needed fix for the Folger Tech FT-5 "Z" axis home switch. I was tired of trying to hold the little nyloc nuts so I modeled the switch clamp with nut holders. The "Z axis screw clamp" is sized to fit a 6-32 bolt tight so no nut is...
thingiverse
... Print Settings Printer: Folger Tech FT-5 Rafts: No Supports: No Resolution: Any. I used .4mm LH Notes: Lay on it's back. ... How I Designed This I used Onshape.
thingiverse
A FT-5 mount for the Chimera+ (water cooled hotend) using Zesty Nimble extruders
cults3d
A FT-5 mount for the Chimera+ (water cooled hotend) using Zesty Nimble extruders
thingiverse
Print Settings Printer: FolgerTech FT-5 Rafts: No Supports: No Resolution: 0.2mm Infill: 25% Notes: After printing, use a small drill to make sure the filament feed holes are wide enough to reduce friction. Use pliers and a little bit of persuasion...
thingiverse
... doesn't cool down at all. Print Settings Printer: Printy McPrintface (FT-5) Rafts: No Supports: No Resolution: 0.3 Infill: 40% or more Notes: Print out of PETG or ABS for strength and heat resistance Post-Printing Pardon the blue tape stuck to it.
prusaprinters
Given the high travel speeds of the x-y carriage on an FT-5, I didn't feel it was a good idea to let the same movement also unwind a heavy filament spool at the same time. I also own a Kossel, which has a a bowden setup where the extruder is mounted...
thingiverse
My FT-5 had several leftover bolts that were suitable length. ...After mounting the bottom bracket, screw the z-stop switch to the bracket using two m3 bolts and two nylock screws, add two M5 screws and nylocks (again, there were leftovers in my kit),...
prusaprinters
My FT-5 had several leftover bolts that were suitable length. After mounting the bottom bracket, screw the z-stop switch to the bracket using two m3 bolts and two nylock screws, add two M5 screws and nylocks (again, there were leftovers in my kit),...
thingiverse
Here is yet another way to help improve your frame rigidity. I would suggest installing them for the Y then X axis supporting the middle 2020 beams. You can also run them along the bottom beams but currently doing so will block your USB port. I'm...
thingiverse
This fits right on the T8 4 Start Lead Screw 8mm pitch and solve the bed going higher than it should when starting the prints. I am using this on the left side since the right side has the high sensor controlling the stop. ... CURA settings Layer...
thingiverse
A simple filament guide which I use in conjunction with CerHewer's FT5 spool stand.. https://www.thingiverse.com/thing:1705478 +Keeps the filament towards the centre and close to the spool so it is far less likely to jump off the spool. +Can...
thingiverse
I wanted a way to hold the glass down to the heat bed while not having to drill thru it. ...This clamp allows you to clamp it down (With a couple screws, I used M4 hex head and tapped the hole) It's low profile and works pretty well.
thingiverse
This is for the Folger Tech FT-5 3D printer's stock hot end. So many of the cooling fan shrouds do not fit well or are for E3D hot ends. The others I've tried either poke in so close that they get melted, of hang below the nozzle which would knock...
thingiverse
Happy with the slim design, though the fan duct could be nicer though :D Good luck and happy printing Print Settings Printer: Folger tech FT-5 Rafts: Doesn't Matter Supports: Yes Resolution: 0,2 Infill: 80% Notes: Can print as you find best, would...
thingiverse
This is a carriage for the Folger Tech FT-5 printer, for mounting an e3D Hemera direct drive extruder and hot end, as well as a BLTouch bed level sensor and a 50x50x15mm blower-style fan for part cooling. Parts Front.stl, Back.stl, Top.stl,...
thingiverse
This is a mount for the TFT32 color touch screen. It includes the main housing and a back cover. The back cover was just revised with this upload so it may not fit. I haven't printed it out yet. Maybe someone will beat me to it. Give em a shot! Round...
thingiverse
This Piece you need to make at least 4 of them. so you can place one on either end of the Guide Railing. While placed start tightening the screws to hold down the guiding rails . starting at one end till you reach the other end! ... when done...
thingiverse
To help prevent the melamine (or any other material) from bending under the torque of the X carriage mounting screws. ... To help improve carriage rigidity.
thingiverse
The belt and zip tie can get in the way. ... This solves that problem.
thingiverse
Simple replacement for the stock button, because why not.