folger tech ft 5 dual extruder 3d models

This converter was designed with the intent to turn the Folger Tech FT-5 Large printer kit into a dual extrusion printer. The original parts were alter to fit heads similar to the CTC 3-D printer. The attachment will sit on the rail system of the...

This converter was designed with the intent to turn the Folger Tech FT-5 Large printer kit into a dual extrusion printer. The original parts were alter to fit heads similar to the CTC 3-D printer. The attachment will sit on the rail system of the...

Cut the Folger Tech Logo out of my Lithophanes with MeshMixer.

This is a bracket to add a reverse Bowden tube to a Folger Tech FT-5 or any other printer with 20x20 aluminum extrusion.

Six m5 X 10 screws and m5 t-nuts required.along with a 5/16" or m8 smooth rod cut to size Print Settings Printer: Folger Tech FT-5 Resolution: any Infill: any but I went 100% Post-Printing Dependent on your calibration, you may have to clean, file or...

This is a tool for building the Folger Tech FT-5. It calls out to space the two upper levels 170mm apart. Had no way of doing it. My dial calipers only went to 6" or a little over 152 mm so I just made my own tool to do the job. Nice to have a 2nd 3D...

I took the BLTOUCH holder for the FT 2020 i3 and mated it with the cooling block spacer to make a holder for the FT-5 since there didn't seem to be one for the stock hot end. I couldn't use the one for the 2020 i3 because the cooling block doesn't...

Printed L and T brackets from PETG (ESUN). ... Very strong and worked well. I have built a Lead Screw version of the FT-5 and used these brackets.I recently added a Corner brace for the FT-5 R2 one of mine was damaged and needed replacing

Happy with the slim design, though the fan duct could be nicer though :D Good luck and happy printing Print Settings Printer: Folger tech FT-5 Rafts: Doesn't Matter Supports: Yes Resolution: 0,2 Infill: 80% Notes: Can print as you find best, would...

This is a fan shroud for Folger Tech FT-5 printers. It uses a 5015S blower fan. ...Print Settings Rafts: No Supports: ...

... Print Settings Printer: Folger Tech FT-5 Rafts: No Supports: No Resolution: Any. I used .4mm LH Notes: Lay on it's back. ... How I Designed This I used Onshape.

I made this for my upcoming 3D printer, The Folger Tech ft-5. I am not the best at designing parts but here it is. Hopefully this will assist when you need to move your massive printer. Extra Part You will need. The handles are designed to be mounted...

This is a well needed fix for the Folger Tech FT-5 "Z" axis home switch. I was tired of trying to hold the little nyloc nuts so I modeled the switch clamp with nut holders. The "Z axis screw clamp" is sized to fit a 6-32 bolt tight so no nut is...

A FT-5 mount for the Chimera+ (water cooled hotend) using Zesty Nimble extruders

A FT-5 mount for the Chimera+ (water cooled hotend) using Zesty Nimble extruders

For the FT-5, I didn't plan to move the extruder, but simply having a bowden tube still means that the distance from the spool to the hotend stay the same, regardless of the hotened carriage position. So I made a clip to mount on the real, above...

... doesn't cool down at all. Print Settings Printer: Printy McPrintface (FT-5) Rafts: No Supports: No Resolution: 0.3 Infill: 40% or more Notes: Print out of PETG or ABS for strength and heat resistance Post-Printing Pardon the blue tape stuck to it.

Given the high travel speeds of the x-y carriage on an FT-5, I didn't feel it was a good idea to let the same movement also unwind a heavy filament spool at the same time. I also own a Kossel, which has a a bowden setup where the extruder is mounted...

My FT-5 had several leftover bolts that were suitable length. ...After mounting the bottom bracket, screw the z-stop switch to the bracket using two m3 bolts and two nylock screws, add two M5 screws and nylocks (again, there were leftovers in my kit),...

My FT-5 had several leftover bolts that were suitable length. After mounting the bottom bracket, screw the z-stop switch to the bracket using two m3 bolts and two nylock screws, add two M5 screws and nylocks (again, there were leftovers in my kit),...

I made this x-carriage so that I could use 2 of the extruders that come with the Folger Tech 2020 Prusa i3. I liked their small design and figured I could use the whole bed area and still allow dual extrusion with this mod. This can be swapped...

SN04 Z Adjuster HICTOP 3DP11:http://www.thingiverse.com/thing:1534152 Folgertech FT-5 Dual Extruder Conversion:http://www.thingiverse.com/thing:2138438 I combined the z-base_rev3(Repaired).stl to the FT-5_Back_Plate.stl. to allow the use of an...

This is a mount to install a inductive proximity probe on the FolgerTech FT-5 and many other types of printers that use this style of extruder. Install it between the heatsink and the fan Must be printed using ABS or other high-temperature plastic.

I really wanted something that attached to the two screws in the bottom H brace of the 713Maker aluminum X carriage for the FT-5. I also wanted something relatively easy to print. Using onebaldman's original 40mm and 50mm bracket I was able to...

This is a carriage for the Folger Tech FT-5 printer, for mounting an e3D Hemera direct drive extruder and hot end, as well as a BLTouch bed level sensor and a 50x50x15mm blower-style fan for part cooling. Parts Front.stl, Back.stl, Top.stl,...

This is for the Folger Tech FT-5 3D printer's stock hot end. So many of the cooling fan shrouds do not fit well or are for E3D hot ends. The others I've tried either poke in so close that they get melted, of hang below the nozzle which would knock...

More stable X-Carriage for FT-5 for bowden hot end.

... Beware the holes for the screws in the mounts will need drilled a small portion otherwise your mount will split. The clamps are fine. This will use 4x m3 x16mm screws you have left over from your FT-5 kit and uses 6x m5 x 10mm screws and 6x T nuts.

This fits right on the T8 4 Start Lead Screw 8mm pitch and solve the bed going higher than it should when starting the prints. I am using this on the left side since the right side has the high sensor controlling the stop. ... CURA settings Layer...

A simple filament guide which I use in conjunction with CerHewer's FT5 spool stand.. https://www.thingiverse.com/thing:1705478 +Keeps the filament towards the centre and close to the spool so it is far less likely to jump off the spool. +Can...