folger tech ft 5 upgrades 3d models

Mods for my 5-gallon tool bucket.Starting from the bottom: outboard caster brackets to increase the wheelbase and make it possible to use locking casters. Makes the whole thing very easy to spin while looking for a tool, and moving on concrete and...

Iam down on very low retractions depending on type of fillament and should lower it by 1-2 mm when done right compared to original 5 mm. I am also on lower retraction speeds 25-40 mms depending on fillament. On nylon i more or less disable retraction...

... pipe, rod, or shaft with a diameter of around three-quarters of an inch. I designed the bracket in Fusion 360 specifically for my Folger Tech FT-5, but it should be compatible with any similar printer with some adjustments to the length of the pipe.

I traced the original STL files from Folger Tech using a workflow of converting STL files to DWG using TurboCad Deluxe and working with the DWG files in DraftSight Pro. Then I used OpenSCAD to create the final 3D model from dimensions and polylines...

This is an upgraded side mount designed to fit my FT-5 3D RepRap Full Graphics LCD Swivel Case(http://www.thingiverse.com/thing:2141320).

Cooling fan for a Folgertech FT-5

Designed specifically for Folger Technologies FT-5 printer. Need to print two of these and add a 3/4-inch PVC pipe from Home Depot. Home Depot sells 2-foot pieces of 3/4-inch PVC pipe, which actually measures 1.050 inches in outer diameter. ... Updated...

I used 6.4mm, which is 5.54mm across the flat part of the nut. You can change the variable **M3Nut** in the openscad to adjust this, then set the variable **DisplayPart = 4** to create a new test print. The order in which I installed this was...

These lines up perfectly with my car. The holes where the e3d slides in need some cleaning to snap it into place without a hitch. You can combine any files you like if that suits your needs. Back OEM Trimmed features the edges pre-cut for E3D...

I reworked this in OpenSCAD so I could shorten it, adjust the diameter of holes and have the plastic avoid solder joints on switches. I realized one M3 bolt was enough to hold it to the extrusion even after adding a bump for aluminum fitment. The...

The stock endstop on the Cloner falls woefully short of expectations. It's extremely challenging to adjust and necessitates a spacer to add anything to the bed surface, whether that's glass or thick PEI. I decided to design a straightforward...

I modified the spool roller by swapping out the pjvpjv version for one with a 2020 T clip. This alteration allows for easy installation without requiring an additional screw. The clip fits snugly into the 2020 T-slot, providing secure support during...

This part enables you to utilize a generic Y-axis LM8UU holder, such as the one included with the Prusa Mendel i2. The STL files for the LM8UU mount used in the kit are not provided on the Google Drive, so this allows a third-party LM8UU holder with...

Just a big bed test I run on my FT6.

This design is tailored to seamlessly integrate a Prometheus hotend onto your trusty 2020 i3. It's essential that you relocate your X-axis endstop to the left side of the X-axis, as this configuration is optimized for a Bowden-style setup and...

This endstop upgrade significantly improves the stability of the FolgerTech FT-5 by doubling down on its anchoring system. ...Two strategically placed bolts now firmly secure the endstop in place, eliminating any risk of slippage along the rod and...

These are the parts I utilized to construct my latest FT-5 bed model.

Original, Enhanced, and High-Torque Mounts for Folgertech's FT-5 3D Printer.

After upgrading my FT-5 with a RJ45 upgrade, I found myself without a part cooling fan. I really like the style of the "Fang" coolers but have yet to find one that fits the stock FT-5 hot end, so I came up with these solutions. Files are available...

Filament mount for a Folgertech FT-5. ...Re-uses the 8020 bar from the front of the machine.

The Bowden mount is paired with a BL touch on the FT-5, bringing precision to your printing experience.

Yet another FT Aura 5 lite mount. ... This is designed to use M2 x 7.5 flange head screws that come with servo motors.

I designed a rugged, lightweight E3D carriage specifically for my FT-5 printer, and this is the result - it's simple yet effective.

I'm adding a layer fan to my Prometheus V2 mount on the FT-5. ...Check out this design: https://www.thingiverse.com/thing:2543862

Original, Stronger, and Dual Spool mounts for Folgertechs FT-5 3D printer. ...Print Settings Printer: FT-5 R2 Rafts: No Supports: No Resolution: 0.15mm Infill: 15% Filament: Doesn't Matter Doesn't Matter Doesn't Matter Category: 3D Printer Parts

Summary Filament Guide for Folgertech FT-5 Designed to Accommodate 4mm OD PTFE Tubing on Bottom Side Works Seamlessly with 20mm 80/20 Extrusion and M5 Socket Head Cap Screws Perfect Companion to My Other Design:...

This is a customized fan mount for the FT-5, utilizing a standard extruder and fitting neatly onto the stock mounting bracket with minimal modification. To achieve optimal performance, we recommend printing it in two separate pieces and attaching...

The FT-5 spool mount requires a precise fit, so we recommend using 18mm diameter wooden or plastic dowels that pass directly through the hole. ...Simply click to confirm your preference and proceed with the installation process.

This is an updated take on one of my other designs, the ProStruder Dual Cooler (https://www.thingiverse.com/thing:2636707), customized specifically for the FT-5 version of the ProStruder Dual Mount (https://www.thingiverse.com/thing:2498096).

Works seamlessly with my other design, available at thingiverse.com: //www.thingiverse.com/thing:1982717 Print Settings: Printer: Folgertech FT-5 Rafts: None required Supports: Not necessary Resolution: 0.3mm layer height Infill Density: 10-20%...