forger 3d models

idk what slicer or print settings were used on the original print, but I had to redo the entire geometry of that area to get it to print right without disturbing the bevel of the rest of that model. Unfortunately, given I don't have the original...

I hope this piece works for you; it was actually the most challenging to model and get right. 9. You should be good to reassemble now! 10. Put the hammer-trigger-piston assembly back in. 11. Lay the cylinder back in place, including the U-clip for...

I recently built some model catapults, and I realize they just use a peg to hold arms into place. So I borrowed that idea, using two interlocking pieces. One piece (looking kind of like a ladder) inserts into slots, and pegs from the top hold the...

This is a well known test model with many remixes.However, I have not seen anyone with automatic temp range.Existing temp tower is “semi-automatic”, they set temperature to preset levels with custom g-code in “before layer change”This print set...

1x M6 square nut - model allows for 5mm thick, 10mm square 1x M6 set screw (10mm length recommended) Important: while printing you MUST put a pause at the layer just before the nut is covered up. Look for the small "box" cavity in-line with the...

You Need: Raspberry Pi Model B or Plus can be purchased here. A 2-channel relay board will suffice; purchase here. Jumper cables are available here. Buy buttons here. Get a webcam from here. Acquire an SD card here. Power your Raspberry with a...

This + rotating the model upside down let's me print the whole thing with no support at all - my print time was 2h 39m and I used small, low-density raft, just in case. https://www.thingiverse.com/thing:4565091 Another thing - it appears that the...

... fills the opening left after you remove the 12 volt adapter socket from the base. It simply slides into place. #Printing# I print rafts with most things, including these models, other than that they are quite simple and shouldn't cause any issues.

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_camera_corner_resolution = 8 stencil_horizontal_position = 50 custom_top_port_corner_resolution = 8 custom_back_camera_x_position = 0...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_left_port_corner_radius = 5 custom_right_port_corner_radius = 5 custom_phone_width = 100 custom_bottom_port_corner_radius = 5...

[Medium Sized Model - 25mm Base] [Presupported in 32mm and 75mm scale]   One of the few Colossals on Tharador not to be born in the bitter Frozen Wastes of Oldavor. Harmara is also one of the few hemomancers to exist out the bounds of Oldavor, the...

The previous file had a gap of 1 mm in the height of the wall between the two cutouts at the front of the model. The replacement file fixes this. Updated "Ability Card Divider" file, to include a cut-out, to make lifting deck from the tray easier. I...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_bottom_port_length = 40 custom_top_port_length = 70 custom_top_port_corner_resolution = 8 stencil_size = 40 printer_tolerance = 0.4...

Post-Printing // model: Prusa i3 MK3 Y Chassis Bearing Straps // This replaces the zip ties that tend to stretch and can reduce accuracy over time. Optionally, also replace the entire strap and bearing with a 1-piece printed version that has been...

It started with a Bachmann starter set with a steam loco and a couple of cars (Durango & Silverton in case my other models didn't give it away). This came with a bunch of EZ-track. I had full intention of expanding my layout so I bought more...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_phone_width = 100 use_mouse_ears = 0 pattern_element_overlap = 52 stencil_shape = 3 custom_back_camera_y_size = 20...

... mount and two each side for accessory mounts. I used one on the right for strain relief for E3D wires, 2 on left for fan mount. 4 on side fan, only two are used depending on fan model. ...2 on cable chain attachment to attach it to extruder mount.

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_phone_thickness = 10 custom_back_camera_x_position = 0 stencil_pattern_element_overlap = 0 custom_top_outer_edge_chamfer_radius = .6...

Different sizes and materials will result in orbs with different focal distances, which may mean you have to adjust the model for yours. Print it strong-- thick walls are a must. You'd be surprised how heavy the orb is. Also, I had to "floss" the...

 I'm confident anyone here can just casually rotate the model right-side up in your slicer.This is licensed CC BY-SA 4.0.  Please feel free to republish this.  Feel free to remix this.  Feel free to use it for commercial purposes and make loads of...

Tools Hex wrench 2mm and Mmm...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_phone_thickness = 10 custom_back_camera_x_position = 0 stencil_pattern_element_overlap = 0 custom_top_outer_edge_chamfer_radius = .6...

Sincethis design is compatible with a whole variety of lampshades, be aware that somelampshades will have to be scaled down or up to fit the base's default settings. Base- Layer height: up to 0.3mm is fine, there's little detail on the Z-axis-...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_left_port_corner_resolution = 8 custom_right_port_corner_radius = 5 custom_back_camera_x_position = 0 custom_bottom_port_length = 40...

So it was time to change the software for a version with customizable options. version 0.1 detail Version 0.2 is a rebuild of the FreeCAD model in OpenSCAD. While working on it some additional settings beside the number of legs made sense. Now there...

My Fusion 360 CAD model has 0.09mm of axial clearance so the printed threads should effortlessly spin together. Extruding over 0.09mm will make it extremely difficult to twist the nut and bolt together using fingers, so just reprint both parts with...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_camera_x_size = 20 custom_bottom_port_x_position = 20 custom_bottom_port_corner_resolution = 8 stencil_rotation = 0...

Also, my printed model needs some clean-up on the outer edges of the ducts (which you can see I did not do). You may have better results with your printer. Printing & Assembly notes: Save the 2 self-tapping case screws when you disassemble the...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: stencil_shape = 4 custom_bottom_port_corner_radius = 5 custom_back_camera_y_size = 20 printer_tolerance = 0.4 stencil_pattern_line_thickness = 30...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_camera_x_size = 20 use_stencil = 0 stencil_shape = 4 stencil_size = 40 stencil_mirror = 0 custom_back_extra_port_x_size = 30...