frame 3d

&nbsp;His video on the project is at: 3D Printed Iris Pendant - YouTubeWith my version, I customized the back and front to form a little monster. &nbsp;There is assembly involved. &nbsp;To complete the project you'll need:</p><ol><li>5 M3...

It doesn't have to be perfectly clean, as long as the bait can go in. How I Designed This This was my first time using FreeCad (realthunder branch) for a 3D print instead of Fusion 360. ...It's quite the learning curve and I'm still getting the hang of...

... only needed for the nut trap part, and I would STRONGLY suggest using tree-like supports, as other supports are significantly more annoying to deal with. Supports can be used for the other parts, but they print fine without. Category: 3D Printing

... this might be overkill.<br/> I only used supports on the front door knob because the magnets hang over the 3mm acrylic doors. Post-Printing Some of the hinges and hingebrackets needed some work to make them fit smoothly. Category: 3D Printer Parts

This was for a 3D printing class. This device can be completely printed from scratch (check out the links below) or you can buy some cheap all-thread and nuts at your local hardware store like I did. This vise can be configured in many different...

Everything prints without support and even without infill; check the recommended print settings.You can print as many blocks and boxes as you like, as long as it is only for your and/or your immediate colleagues’ usage.You are not allowed to copy or...

By rotating the 3D-printed mid-air LED printer, the LEDs move in a circle, writing lines in the air. Arduino synchronizes the blinking of the individual LEDs. The color of the LEDs can be chosen as long as the right series resistor is used. For 20 mA...

In real life, this would compare to a almost 1.5 meter tall 3D printed something with one tool change per layer (at 0.2 layer height). BOM To build this thingy, you'll need: - The printed parts - A standard size servo - A servo horn (preferably...

The purpose is to allow new 3D printer users to start learning with the basics and produce models that let them focus on just a few potential problems at a time. [Opinion: Manufacturers often include files for one or more complex pieces with a new...

They are great bearings, however if you break one trying to ram it into the new carriage like I did, or do not want to destroy the old carriage, you can just 3D print some. I recommend using ball bearing LM6UU bearings due to the weight and angle of...

... <p>Print parts as-oriented. Supports not required, gaps are intended to be bridged.</p> <p>The end caps in particular have very tight dimensional tolerances. Prefer underextrusion to over extrusion. Category: 3D Printer Parts

... to get too in depth.</p><h3>Hole Spacing</h3><p><strong>Hole Distances for drilling. (You can also just print the plates first, and put them against the printer to figure out the centers instead if that's easier for you.Category: 3D Printer Parts

The STL is now clean and no longer reports errors in blenders 3D print validation tool. This may help to get a cleaner slice on some slicing software. In addition, the top and bottom latches were refined so that they should hold a bit better,...

I thought that that is pretty cool, and I wanted to 3D Print something like this myself.&nbsp;I started designing and finally after about 10 different prototypes and many failed prints, the Slide n‘ Seal is at a point where I can „release“...

... and feed the Bowden tube though that hole at the top. It doesn't go al the way through though. Use supports but they are only for the line hole. The word Prusa is nicely show on the vertical support as well. Category: 3D Printer Accessories

After years of noticing wear and warp on my reusable Rocektbook notebooks, I decided to put my 3D printer to work to solve the issue…And voila - multi-material (TPU | PETG | TPU), customizable (colour, infill pattern + density) notebook covers that...

I thought about 3D printing the rods as well, but I didn’t get good results with this technique. Regarding different 50 mL tube designs, I can tell you that I have tested 50 mL tubes with built in stand and they work as well.</p> <p>Enjoy.</p>...

... go ahead and start tightening them down. Of course the brackets are plastic, so don't overtighten them or they may crack. (Optional) Once everything is to your liking, go ahead and insert the rod caps into place. Category: 3D Printer Parts

6x minis boxes 8x card boxes 2x under_card boxes one of everything else The two trays that sit under the card boxes can be used to hold other 3D printed objects, such as staircases, secret doors, etc. They're just there to fill space so use them as...

I wanted to do something like this for some time, but it turned out to be quite tricky to get the design right for 3D printing. One key point is that the pins have to be printed standing up, which reduces their structural strength quite a lot. To...

After I picked up my first 3D printer I decided to make this side handle. It took a while to get to, and a few prototypes to get to this point.</p> <p>There's two parts to the handle. The handle and the body. The body has the three triangles that...

&nbsp; I started the design for a Makita/Bosch adapter I bought from Amazon, but switched to a 3d printed model. &nbsp;I am including <a href="https://www.prusaprinters.org/prints/134967-makita-18v-adapter-remix-for-3mm-bolts">my remix</a> of <a...

&nbsp;I used 3D Gloop PET glue, but others should work. &nbsp;I am not sure if super glue will work with PETG very well, and it does have a tendency to leave a white residue when it cures.</li><li>The mounting stakes are NOT glued in, so they can be...

Waiting for specific details about dimensions from Mario. 14 Jun 2016 Design of SG90 servo- and raspi- mounting finished. I also got the sandwich panels and can start the assembly tomorrow. 16 Jun 2016 Upload of modified flap corner parts as well as...

ACTUALIZACIÓN 22/06/2019 Eje unión de ventiladores V2 (incluye posibilidad de tuercas en ambos lados) Soplador de capa con doble ventilador 5015 para Anycubic Chiron, es el complemento al soplador simple que puedes encontrar en esta dirección...

I have included a few files, several ready to slice and go and two that can be opened in OpenSCAD and played with, because thats the fun of 3D printing right? The tinkering! The comments in the .scad files should make it pretty clear and i've...

Then this is a good read: https://hackaday.com/2019/02/28/threading-3d-printed-parts-how-to-use-heat-set-inserts/ ** TIP OF THE DAY: get those special 'threaded inserts tips' for your soldering iron so you don't accidentally deform the upper brass...

1.) 3D print all of the pieces, Cut the mirror pieces to size (CAREFUL!!!), and laser cut all of the lenses. You could probably also cut the acrylic out with a bandsaw, but laser is easier. 2.) Glue the 1" lens into the slot of the...

Other than that may some cleanup of 3d printed parts require as sanding or hole cleanup with 3 mm drill bit. Printing: Some parts require small supports (mid plate, fan ducts). Other than that 0.2 - 0.3 resolution is enough. Print quality...

Either hard wire or use a 2.1mm jack. One of the corner covers has an opening for the cable, so make sure you identify this one and reserve it for the correct corner. Print instructionsCategory: 3D Printer Accessories Summary Rather than let the LED...