frsky x9e 3d models
2305 3d models found related to frsky x9e.thingiverse
A FrSky X9E Gimbal Protector Print Settings Printer: CL 260 Rafts: Doesn't Matter Supports: No Resolution: 0.2mm Infill: 20% or more
prusaprinters
A FrSky X9E Gimbal Protector Print Settings Printer: CL 260 Rafts: Doesn't Matter Supports: No Resolution: 0.2mm Infill: 20% or more Category: R/C Vehicles
thingiverse
Parasol para el disply de la emisora FrSky Taranis X9E
thingiverse
Simple cradle to attach a Dragonlink V3 UHF transmitter module (V2 might fit as well? ...can't try by myself) to a FrSky Taranis X9E. ...Just put it inside the Taranis' handle and drop the TX into, done!
thingiverse
A series of modifications to a standard X9E tray radio allowing easier access to the left-hand joystick for a modeller with severe physical disability. Could also be used to add a third joystick to the transmitter for gimbal control. Standard left...
cults3d
A series of modifications to a standard X9E tray radio allowing easier access to the left-hand joystick for a modeller with severe physical disability. Could also be used to add a third joystick to the transmitter for gimbal control. Standard left...
thingiverse
Extra extentions for Taranis pull transmitter. ...ABS 100% infill.
cults3d
Larger and smooth gimbal stick (d = 10 mm, l = 43 mm) with support for the thumb.Hole for M4 thread.
thingiverse
Larger and smooth gimbal stick (d = 10 mm, l = 43 mm) with support for the thumb.Hole for M4 thread. Print Settings Printer Brand: Prusa ...
thingiverse
FrSky R9 internal cover for X9e. The standard module does not fit in the body and therefore I made the cover for this part. ... Made from PLA Replaces the original cover
thingiverse
Its a different handrest for the r/c transmitter FrSky Taranis X9E. You need two of it and four adapters. You have to srew the adapter with a M3 countersunk bolt each. Then you can clip and release the handrests to the transmitter without tools. ...
thingiverse
I need a battery holder for my Frsky Taranis X9E Radio and couldn't find one, so I made one. I put cut-outs for zip-ties to hold the battery in place. I used a Qidi Tech X-one 3D printer. Simplify3D for a slicer software. ...ABS red 1.75mm filament, but...
thingiverse
This is a modification for the FrSky X9E radio designed to allow easy use of the full TBS Crossfire module. This modification protects the module and fits inside the transmitter case without a need to remove anything. Crossfire or any other...
thingiverse
Taranis X9E Side Rail. ...These replace the Plywood rails you get with the Taranis Wooden Tray
thingiverse
I noticed this protector in another design of MarenB and I also scaled it up to match the X9E gimbals ... ... Maybe someone will find it useful ...
thingiverse
There wasn't much of a selection of gimbal protectors for the X9E transmitter, so I quickly whipped up this design. Minimalistic in design, to reduce filament usage but strong enough to be functional. I have printed in TPU and it is a snug fit...
thingiverse
Reworked JPrikkel's original box and lid to fit the module slot that is enclosed inside the X9E tray version. The RF antenna wire now exits at the side. ...Thanks to the original author for his fantastic module design - I've just successfully built one...
thingiverse
Taranis X9E Belt bracket. For the lower holder you can use the original screws. On the upper side I used a M5x30 mm bolt with some washers and a nut. ...The Taranis is more stable and in level with this thing.
thingiverse
This "thing" allows to set 2 antennas in place of the original handle, and once detached, allowing to fit the x9e in the soft case for transport without disconnecting the SMA connector. The male/female plug is an octagon allowing to set an...
cults3d
An adaptor plate for the tararnis x9e to allow the fitting of D4 sticks. You will have to remove the silverring around the standard gimbals, just pops out. I sanded the ring that was deliverd with the 4D sticks so that it fitted tightly. ... You may...
thingiverse
An adaptor plate for the tararnis x9e to allow the fitting of D4 sticks. You will have to remove the silverring around the standard gimbals, just pops out. I sanded the ring that was deliverd with the 4D sticks so that it fitted tightly. ... You...
thingiverse
Originally the X9E is equipped with harness arms that are too flimsy and causes the radio to hang forward down in an uncomfortable angle. Add a FPV monitor to this and the whole system becomes nearly unusable. One other serious drawback is that the...
thingiverse
FPV Monitor mount for Taranis X9E. ... Requeriments: 1 x M3x20mm screw 1 x M3 Nut 1 x M6x40mm screw 1 x M6 Nut
thingiverse
I loved the quadcopter TX keychain by Mike-vorn-Mars (https://www.thingiverse.com/thing:2548116), but wanted an FrSky inspired version: This is a stylised Horus, X10 or Q7... you decide. It's designed to be printed as four pieces, 1 x TX, 1 x...
cults3d
I found the inner hole diameter slightly too tight to fit my gimbals (this may be down to ABS shrinkage and printer calibration). ... This remixed version of Destelant's original work opens the inner hole up slightly and adds a mild chamfer to aid the...
thingiverse
This is a plate for the taranis handle. It´s help full if you use a lot of those switches. I`ll print one for every model I have and name the switches on it. ...(NOT TESTED YET)