g305 to g303 mod v2 by 3d models

Part cooling duct for 4MAX PRO V2 with V6 (23x16x10) heat block.

This part allows the vents to breathe, improving airflow to the PSU. Cutting the original PSU shroud would also work, but I did not have the tools for the job. Printing: 20% Infill would be fine. But if you want a more rigid piece you can...

Based on the ALS Nub Mod by Oregon Trail Defense. Reverse angle matches the ergonomics of your thumb, better grip on the retention button, larger pressing surface. Compatible with Safariland 6354DO and similar, the TMC 354DO. Needed: 1...

... it easy. The product used can be found on Amazon under B00X5MDUD4. Due to the inadequate adhesive on the back of the LEDs, I employed thin strips of Gorilla Tape every three to four inches to secure them firmly to the PET-G enclosure components.

Mechanical Mod Button Feeder Parallel System for 18650 Batteries. Operate with One or Two Batteries at a Time. ... The Package Includes Custom Plates, a Magnetic Cover, and a Reference Magnet.

These are brackets I designed to upgrade the size of my print bed on the MP Select Mini V2. They allow you to attach a larger build plate with precision. The tolerances on the holes may be a little tight, so some post processing may be necessary to...

... Here is the link to the Magnetic Filament Monitor https://www.filastruder.com/collections/electronics/products/duet-magnetic-filament-monitor If you would like to try my V1 mod that can be found here. ...https://www.thingiverse.com/thing:4602537

The position of M4 threaded hole is adjusted so that the pneumatic joint of the extruder and the nozzle can correspond The biggest advantage of this MOD is that it does not need to change the air duct, fan head and automatic leveler. thx to...

Für diesen Mod muss die Linearführung etwas gekürzt und auf der Stirnseite montiert werden. Mit dieser Anordnung wir der Kipphebel emliminiert und die Antriebsriemen laufen jetzt parallel . Das wirkt sich beides natürlich auf den Druck aus. ... ...

There's three iterations - two recessing the switch as to avoid accidental activation (my printer sits on my "everyday" desk and I do not want to accidentally switch it off while a print is going on). One recessed version is narrow, one widens up a...

... 2 types of slider available (blank or grooved jaw) DESK CLAMP VERSION What's completely new here is the C-clamp which includes one ball-joint system where the shaft is fixed by a M8x10mm Allen screw (with cylindrical head) to the vise base bottom.

Based on the G305 Flat Bottom Shell by FortyOne. Created because i couldn't find one that fit my taste. ...Printed on Anycubic Photon Mono without supports straight on the base with 0,051mm layerheight, you loose some definition in the bottom to the...

Lam Tang's CALIBRE V2 - A cutting-edge design that captures attention!

This is for the Mutiny v2 (bando arms) https://youtu.be/7yRa2O4a8Fc

20mm.The screw position on the slider part has been accurate re-positioned to provide more straight clamping movement.2 types of slider available (blank or grooved jaw)DESK CLAMP VERSIONWhat's completely new here is the C-clamp which includes one...

NANO VISE V2 is here!This is a complete renewal of my quite famous Nano Vise https://www.thingiverse.com/thing:2066644 and in fact the vise base and slider has undergone some design & size corrections like no more sharp edges at the dove tail...

If you don't have one of those tools, there are other options on Thingiverse that work, such as https://www.thingiverse.com/thing:1574661 Note also: The current v2.1 Raspberry Pi camera comes with the sensor block not firmly attached to the PCB, but...

I like to print the blades individually in vase mode as I've had great success with this method, so since I took the time to split all the objects in this STL into 1 STL per object, I figured I'd share. Yes, I know it takes a while to print it this...

I designed a modification to the "Ender 3 Pro Rail Cover" created by wtlx on Thingiverse. ...My version features reinforced walls and includes an engraving that proudly reads "Creality 3D".

... to employ square nuts instead of heatserts. Additionally, I need to manufacture a 45 degree block so that I can position the camera diagonally behind my soffit. ... Print the hood with the large end facing down; you may prefer to use a brim.

... To enhance the rigidity of the backplate mount, I made a few tweaks: I increased its thickness by 0.5mm, enlarged the hole diameter to accommodate a rivnut, and added a small retaining clip. Additionally, I enlarged the hole size in the fan mount.

Ender 3 Direct BL Touch Setup and Calibration Guide Getting Started with Ender 3 Direct BL Touch To set up the Direct BL Touch on your Ender 3, begin by carefully removing any existing sensors or probes from your printer. Next, locate the BL Touch...

I decided to design replacement parts for the stop ends on the aluminium extruder such in a way that no holes are drilled and by using piggy back connectors on the original switch all original parts are retained so the warranty is not affected. Turn...

By manoeuvring a small screwdriver through the hole where the power inlet was removed you should be able to compress the retaining clips on the top and bottom of the switch ( I used the hook end of one of the supplied allen keys which was ideal for...

This is obviously preference, but yea, I had to increase travel a smidge by filing down both surfaces to be happy. Could be related to sloppy tolerances also, but the default amount should "work" but I wanted a little travel (like 1/8-1/4") rather...

I couldn't get Cryo's ring scroll to print well in FDM, so I edited it to work with the original G305 scroll stem.

Modified Version of Filament Guide by iceman6paq for RF100v2. Added Cable Holders and Supports, Lengthened Shaft Slightly. ... Print With Supports in Place.

I'm experiencing a technical glitch at the moment. ...Please stand by while I try to resolve this issue.

I make custom mods for the G305 mouse with FK2 and S2 shapes. You can check out my work on Instagram at https://www.instagram.com/piranhamousemods/. Follow my current project on Twitter at https://twitter.com/ModsMouse. Special shoutout to...

But anyway my version was modified from Violin_Neck_3A.stl so I have changed it for support now that this AM it has stopped failing and can be moved over, because the design did not do this originally To stick the 2 neck parts together I'm going to...