geeetech a10m 3d models

If you decide to do this, use the full 220mm x 220mm build volume, which is technically the full capacity of the A10M (235x235mm), but most people will be printing in the default area of 220x220mm. For Cura, adjust these settings: * Adhesion type =...

This is not the normal fan for the A10M, but it did come stock out of the box, so maybe it's the new one, or the old one...whatever it's a 4020 blower. I felt the stock one was a bit restrictive and after going down the rabbit hole of researching...

I swapped out the subpar hot end that came with my A10m for an E3D V6. The quality and reliability of this new hot end far surpass those of its predecessor, even if it does lack the mixing capabilities. I was able to reuse the stock fans and fan duct...

This is a replacement lever designed to match the original Geeetech 3:1 geared Titan Extruder Clone perfectly. Two versions are available - one SLA version that closely resembles the original and another simplified version for standard FDM printing.

The difference in diameter between the long piece and the short piece is due to the fact that the spool fits well on the metal support of Geeetech spools, while the small piece fits well on the metal support. ... If it doesn't work well, try putting a...

This firmware has been tested on an A10 machine, but it's likely to work just as well on an A10M. To get started, you'll need to: - Print a new Y endstop mount because the cables are too short for this printer. - Create an extension power cord so...

Hi rabbits, This is my second approach to a fan duct for the new A10M model from middle 2020. Based on herome series, I use the 40*20 fan and the curved pipe to allow the air flow from fresh air. You will need to combine this fand duct with the...

This is a replacement lever for the original Geeetech 3:1 geared Titan Extruder Clone. There is one SLA Version which looks most alike the original and one simplified version for standard FDM print. Print at least in PETG or even in ABS to last...

The Print a Lot filament adapter for the Geeetech A10M/A10 printer has been modified. ...The H3DX adapter was reworked to change the support diameter from 40mm to 33mm.

My Geeetech A10M model boasts an unconventional design, featuring a motherboard situated on the right side of the LCD screen as seen in the accompanying photograph. ...Notable differences from standard designs found on Thingiverse are due to the unique...

Because original Geeetech A10M firmware for me had wrong direction in both extruders With this FW i'm up to date and all working perfect for me Updated steps/mm after calibrating my printer X= 80.2 steps/mm Y= 80.4 steps/mm Z= 417.8 steps/mm E= 400...

The Purge Bucket is designed specifically for the Geeetech A10M, A10, and A20M 3D printers, as well as the A20 model. To install this component, you will need to use two M5 x 40mm hex head screws that provide a secure mount. ...The purge bucket itself...

My first concern when I purchased the Geeetech A10M was the extremely vibrant green glow of the LED display so I installed a 12864 reprap screen to tone things down. This is a mounting system for the LCD display, I have a "Der Skorpion" parts cooler...

... based on a Chimera clone. Print this with PETG, ABS, resin, or any material that can withstand high temperatures. UPDATE: Check out the v2 mount with an improved cooling solution: https://cults3d.com/en/3d-model/tool/geeetech-a10m-chimera-mount-v2

I designed this mount for the Geeetech A10M and is based on a Chimera clone. Print this with PETG, ABS, resin, or anything that can withstand high temperatures. ...Print Settings Printer Brand: Anycubic Printer: Predator Rafts: Doesn't Matter Supports:...

Geeetech A10M printer.cfg file for Kilpper firmware (works with Creality Sonic Pad). Still in progress. My Cure g-code settings: Start g-code: G90 G92 E0 ; Reset Extruder G28 ; Home all axes G1 Z2.0 F3000 G1 X5.1 Y20 Z0.3 F5000.0 G1 X5.1...

This is a mount I designed in Fusion 360 to mount the BigTreeTech ZSYong mixing hotend on the Geeetech A10m. It mounts it so both the original fans cooling fans, the stock part cooling fan and the 3D Touch bed sensor can be used and keeps them in...

This is a mount I designed in Fusion 360 to mount the BigTreeTech ZSYong mixing hotend on the Geeetech A10m. It mounts it so both the original fans cooling fans, the stock part cooling fan and the 3D Touch bed sensor can be used and keeps them in...

This is a mount I designed in Fusion 360 to mount the BigTreeTech ZSYong mixing hotend on the Geeetech A10m. It mounts it so both the original fans cooling fans, the stock part cooling fan and the 3D Touch bed sensor can be used and keeps them in...

want bltouch in different position and one piece

The original extruder's predecessor, the A20M, is an almost exact replica of its original counterpart. The original came damaged and until they can bring me the replacement part, I have created this prototype as a temporary fix. ...It fits perfectly...

<p>The original mount that I designed worked well, but I didn't like the cooling solution that I was using. I've modified the design to allow two 5015 blower fans to be used on each side. The improved cooling makes a huge difference.</p> <p>You'll...

The original mount that I designed worked well, but I didn't like the cooling solution that I was using. I've modified the design to allow two 5015 blower fans to be used on each side. The improved cooling makes a huge difference. You'll need some...

I've been relying heavily on Prusa Slicer lately, achieving fantastic results in the process. To make it stand out even more, I decided to give it a facelift. Now, each of my printers has a custom build plate that not only enhances its appearance but...

The stock fan is a bit too close to the heat block, causing my original one to develop a hole from melting. This was after printing PLA at 210 degrees maximum. The new design takes this into account by keeping the block clear of the fan's airflow. My...

The original mount that I designed worked well, but I didn't like the cooling solution that I was using. I've modified the design to allow two 5015 blower fans to be used on each side. The improved cooling makes a huge difference. You'll need some...

The original design worked well, but I wasn't satisfied with the cooling solution that was being used. To make a significant improvement, I redesigned the system to accommodate two 5015 blower fans on each side, which greatly enhanced the cooling...

This is a tailored Y-Belt tensioner adaptation, specifically designed to seamlessly integrate with the Geeetech A10/A10M without requiring any additional components or modifications beyond a standard M5 bolt and nut.

This is a fan cover specifically tailored for the Geeetech A10/A10M model from 2019, given that there are various models available on Thingiverse catering to older versions. The design was created using TinkerCAD to perfectly fit my own 2019 model.

There are several remixes of the original work, but most are designed for metric threads, which won't fit Geeetech A10M's 1/8" thread. If attached directly to the feeder, they will come loose whenever a tube is detached due to identical rotational...