quiet ender 3 3d models

had some struggles to mount a Noctua fan 40x20 as hotend cooler. with this remix of that awesome Cooler mount, it fits perfect. ...

... the wall thinkness when you slice it. I used 1mm. To place one at each corner you will need to print 3 of the version with 4 blocks on the top, plus one with just 3 (the last block would foul on the main board casing, so has been removed) ;-)

this is a very easy mod to the ender 3 standard power supply (not the Meanwell power supply) the fan is a NF-A9 Noctua fan 92mm. the fan is soft mounted with the included rubber plugs. and the only part needed apart from the fan and some heat-shrink...

A replacement for the mainboard housing for the Ender 3 that allows you to keep all electronics in a single box cooled with a single 120mm fan. It will house the standard mainboard, a raspberry pi 2 (feel free to remix for a rpi3) and a buck...

https://www.thingiverse.com/thing:5236927** The stepper motors on the Creality Ender 3 v2 3D printer are very quiet, which makes the cooling fans the loudest parts of the machine. If the user replaces the included fans with quieter alternatives, the...

... from nozzle x=43 y=-2 BLTouch v3.1 mount added on request (not tested). Distance from nozzle x= 24 y= 3 Distance heater block to Bltouch side 7.5mm (to close?) 2021-02-03: update Ender-3 V2 support removed beacuse of problem with Bltouch

This is an Creality Ender 3 board fan cover remixed from the original great design by mtlcan. I've placed it in transverse position to direct the fan noise away from the user (frontal position). Tested with a phonometer it scored 7db less than the...

I like the idea of quiet feet, but they keep falling over whenever you slide the printer.... after I threw the first set I printed in the trash, I went into Freecad opened the stl and added some side blocks to keep it upright when sliding. ... Note:...

Creality Ender 3 v2 Quiet Cooler v2 w/ CRTouch SupportThe stepper motors on the Creality Ender 3 v2 3D printer are very quiet, which makes the cooling fans the loudest parts of the machine. If the user replaces the included fans with quieter...

## Ender 3 V2 Quiet Fan Shroud/Cover Much quieter, good airflow, easy to remove. Instructions: - Buy four <a...

Easy way to mount 92 mm fan in stock hole. Recommended remove stock fan grill for better Airflow . ...Enjoy!

(Creality Ender 3 v2 Quiet Cooler) I wanted the printer to be as quiet as possible, and the cooling fans were the loudest part of the system. Out of the box, the printer uses one rather loud filament cooling fan. I made a cooler that allows you to...

A while back I made an alternative cooler mount for the Creality Ender 3 v2 3D printer. (https://www.thingiverse.com/thing:4969159) I wanted the printer to be as quiet as possible, and the cooling fans were the loudest part of the system. Out of the...

80x80mm quiet fan solved the problem of terribly noisy standard 40x40 fan. Use the original screws to mount the bracket and four screw of your choice or cable ties to mount the fan. ... Mind the natural air flow - hot air is being sucked from the PSU!

Next version of adapter https://www.thingiverse.com/thing:3388548/ this time is 80mm Easy way to mount 80 mm fan in stock hole. Recommended remove stock fan grill for better Airflow . ...Enjoy!

Hi, I'm new to 3d modeling so do not expect to be perfect, i modified the original .STL file (https://www.thingiverse.com/thing:5236927) to make the ducts longer and cool the volcano block attached to the original ender 3 v2 dissipator. ...

EDIT 22/02/23: I have included a modified version of the grille to include supports for an endoscope mount like this: https://www.thingiverse.com/thing:4742800 This is a remix from tllado's Quiet Cooler for Creality Ender 3 v2...

Remix of 4969159: Adapted the file to make it fit on my Ender 3 Pro: - fixed position of M3 fixation screw - adapted one of the diameters of the two extruder fixation holders (one was too big) - fixed collision of model with M5 Nut/Screw - made the...

I removed one fan to make room for a bltouch probe and adjusted the design to be printable with only simple printbed support. This remix is a bad idea, you should not use it. To axial fans probably delivery barely enough part cooling to print in...

This is a quiet non-squeaky Filament Guide for the Ender 3 because we use a bit of PTFE Bowden tubing to help with guidance, making it completely quiet. You should have some extra PTFE bowden tubing around. This also means that you should be able to...

... the green rocker oscillate. Two red stoppers are mounted on the green rocker. Measure to create some breaking force for the green rocker is not shown. The mechanism is quiet because when the rocker goes back, the pawl does not contact the wheel.

You will need: 2: 40x40x10mm (quiet) fan 6: M3x10mm screws for the adapter parts 8: M3x14-16mm screws to fix the fans to the adapters Quiet fans for the ender 3 v2:...

If you print it feel free to give feedback if it needs improvements!The metal protection will have to be removed to use this.You will need:2: 40x40x10mm (quiet) fan6: M3x10mm screws for the adapter parts8: M3x14-16mm screws to fix the fans to the...

No description provided.

Hello and Servus This Direct Drive Conversion Kit is for a Creality Ender 3 / CR10 Printer. Some Direct Drives have a poor cooling or a loud fan or a bulky style... I could not find a quiet, compact Version with good cooling; so I made one myself. ... ...

Design goals: Quiet! Better part cooler Same or slightly better hotend cooling Low weight Easy acess to nozzle Good visibility of nozzle Easy to remove part cooler Design choices: 50x50x15mm axial fans (radial fans is supposed to be noisy) ...

3D model of CPU fan Be quiet! ...Silent Wings 3 120mm High-Speed (BLO68) made in SOLIDWORKS 2016

I'm going to switch to a 12V fan, but drive it through an MP1584EN buck-converter to lower the voltage to keep the fan quiet, but run it a bit faster than the current one.~~Update: It turns out that cooling wasn't the problem. I was overdriving the...

I'm using it in an Anycubic Kossel Linear Plus for an easy upgrade to TMC2130 drivers (makes it super quiet) along with a Raspberry Pi (see [thing 4015230](https://www.thingiverse.com/thing:4015230)) to run Klipper firmware. The cables can be routed...

... component parts is attached. If there are questions, please, write comments. Good luck! 23.10.2017 added: Configuration.h, additional photos. 03.03.2018 added: 3D-models SLDPRT 09.03.2018 update: plywood_6mm_RPD3_h-bot-corexy to ver.3.9.7