gopro scope adapter 3d models

this scope adapter fits snuggly onto a 2 inch diameter scope eyepiece! Interested in having Product Development, R&D, or Prototyping work done? ...Check out our website with all of our services at www.Createcafe.ca

This thing was made with Tinkercad. ...Edit it online https://www.tinkercad.com/things/hqA9ZMbUqIz

This thing was made with Tinkercad. ...Edit it online https://www.tinkercad.com/things/hqA9ZMbUqIz

Two piece adapter to mount GoPro Hero4 in housing to a Spotting Scope (Meade 60mm). Fits into eyepiece port. ...Part A size: 3.0"Dx0.625" Part B size: 2.490"Dx1.56"GoPro CAD Model from Graham Baldwin GoPro HERO4 Silver

Two piece adapter to mount GoPro Hero4 in housing to a Spotting Scope (Meade 60mm). ...Fits into eyepiece port.Part A size: 3.0"Dx0.625" Part B size: 2.490"Dx1.56" GoPro CAD Model from Graham Baldwin https://grabcad.com/library/gopro-hero4-silver-1

A while back I bought an adapter for my GoPro Hero 4 to use with my spotting scope. Well, technology moves on, but the company that I bought the adapter from didn't. They never made an adapter for the Hero 5. I even recently bought a mount for my...

Adaptor to mount a Galaxy S7 case to my spotting scope. ...Phone case will be attached by Neodymium magnets This adapter was designed for a single scope application, not likely usable for anything else.

Customisable scope adapter for digital night vision add-on. ... Converts the eye piece of a scope so you can glue it to some 40mm abs waste pipe therefore this should be printed in abs.

This GoPro mount will fit a 26mm scope. ...5mm bolts and nuts for mounting.

... Lower" in slot. Screw in the 1 1/2" 6/32 bolt. 2) Take main body and slide the "Scope Mount Upper" in slot. Screw in the 1/2" 6/32 bolt. 3) Glue the "GoPro Bracket" to the "Scope Mount Lower". ... (ABS glue is recommended) Super Glue works fine.

This is is mount that goes on the scope of your crossbow for a GoPro. I printed in both PLA and ABS - whichever you feel is best for you. ... V2 is the same but looser tolerances for the GoPro fitting inside as well as the screw hole larger.

http://www.thingiverse.com/apps/customizer/run?thing_id=62800 Instructions Using the following options: gopro_ext_th = 3 gopro_bar_th = 3.2 gopro_captive_rod_id = 3.8 gopro_ext_len = 20.7 gopro_bar_screw_head_d = 6.2 gopro_captive_rod_angle = 45...

This adapter will turn your cheap finder scope into polar alignment scope for Celestron CG-5 mount. I used 10$ Seben 5x24 [http://tiny.cc/7ofaly] finder scope purchased from ebay for this project. Remark: I made a 1,5 cm shorter print of this...

A quick and handy adapter to use your 30mm scope accessories on your 25mm scope. Shown in the picture is a 30mm bubble level mounted on my 25mm scope. ... PRINT TWO copies, one set for each side - place the larger side on the bed.

This design has two parts to it; the scope cam mount (that sticks to the camera) and the scope cam adapter (that slides on to the scope). I used a action camera that is able to record in 720p 120fps and has 4x digital zoom. However this is not...

This design has two parts to it; the scope cam mount (that sticks to the camera) and the scope cam adapter (that slides on to the scope). I used a action camera that is able to record in 720p 120fps and has 4x digital zoom. However this is not...

This adapter screws on to the threads on the scope, and allows anything that takes 49mm filters to be attached. Other thread sizes could be adapted to 49mm or this could be remixed for different sizes. After using this, I came to the realization...

Microsoft LifeCam or StudioCam, ...) to a spotting or rifle scope (e.g. Bushnell, ACOG, Schmidt & Bender 5-25/3-27, ...). Or customize to fit your own equipment. Instructions Purposely slightly...

OpenSCAD designs for digi-scoping with a Pixel 3 to a Meade binocular, a Vortex spotting scope and an inexpensive microscope.

This adapter mounts a 1/3 in camera to most scopes. The monitor and IR flashlight then allow you to see in the dark. Print Settings Printer: Wanhao Duplicator i3 ...

I remade the thumb screws with a bit of knurling which leaves the adapter smaller to pack and access when I want to place on my binos or spotting scope. Uses: *one M4 nut in the base *one M4 x 13mm Philips screws. One gets placed in the...

I've created this to mount both my lpvo scope and my reddot to my airsoft. It should work with scopes that have a 30mm tube. M5 Screws are used to screw both halves together. 

Just the basic envelope of the thing, don't need to get overly anal retentive and make it look like the exact thing with all the bells buttons and needless features.This will be made from HDPE because it only needs to hold the camera fixed in...

... Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=445259 Instructions Using the following options: insert_length = 30 scope_dia = 90 pipe_outside_diameter = 40 pipe_inside_diameter = 34

... Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=445259 Instructions Using the following options: insert_length = 50 pipe_outside_diameter = 43 scope_dia = 42 pipe_inside_diameter = 40

... Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=445259 Instructions Using the following options: scope_dia = 42 pipe_outside_diameter = 43 pipe_inside_diameter = 30 insert_length = 50

... Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=445259 Instructions Using the following options: pipe_outside_diameter = 5 insert_length = 40 scope_dia = 35 pipe_inside_diameter = 35

... Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=445259 Instructions Using the following options: insert_length = 40 scope_dia = 45 pipe_outside_diameter = 43 pipe_inside_diameter = 40

No supports. ...0.1mm layer height. No bed adhesion. Made for the monstrum lpvo mount and adapted to fit 1" scopes into it.

dovetail adapter for the williams otpics ZenithStar 61 telescope and the ZWO 30 mm guidescope