grind blocks for roller skates 3d models

This design is fully compatible with the Rollin On 20s roller (bearings are slightly lower, but the spacing is about the same) so if you can print it as a replacement for just one side if you have a cracked pin. SolidPin-Snug hasn't been tested, but...

I did notice two different things though: If I use charcoal for the foundry, the part comes out perfectly sized (same as the correct-sized mold). If I use a propane foundry, I get some shrinkage (about 4.5 mm in the long axis) So if you can get your...

My K2 "Alexis" inline skates were equipped with a brake pad attached to the shaft of the rear skate on the right foot. Following a fall that left me severely bruised from the brake being jammed into my back, I decided it would be better without it.

I made the TUSH One Piece which is great, but found my cardboard spools liked to roll into the edge so I ended up making these 8mm wide bearing roller guides.The only downside is that they don't fit through the bottom slot so bearings had to be...

Hockey Players Get Ready to Hit the Ice with Updated Skates Version 2020.4.1 is Now Available for Character Creator 3 Users Level of Detail 0 (LOD0) Optimized for High-Performance Rendering

I needed a solution to secure the rollers in place, but couldn't utilize the supplied screw mounts. To address this issue, I designed and created a simple piece (white) that features rubber feet on its bottom. This setup works flawlessly and...

because glasses gave rounded faces, they don't make good contact with the rollers so increasing the presure helps. Inside the glass their is a wheel (<a href="https://www.aliexpress.com/item/1005003982193085.html">a Plastic Bearing 6200 10x30x9 from...

This is a spool roller that replaces the bearing holders of "Universal Spool Holder".Improvements:There is no need to adjust the bearing holders when replacing to a different sized spool.Rods can take more wight without bending.Printed with PETG,...

I tried EdNiedziejko's elegant solution of printing the bearing pin as a glue-on piece, but with my clumsy fingers, it just wasn't working for me. ...And then I thought; "Who says the roller has to be plastic too?!!" Just because I have a 3D...

Introducing building blocks that bring the youngest minds into the exciting world of addition and subtraction. ...With these versatile tools, kids can also discover the joy of creating geometric shapes, numbers, and even letters.

Upgrade your Open Press Project press with a stainless steel tube roller. I bought some ∅32mm , 1.5mm thick (∅29mm inside) polished stainless steel tubing and cut to length (75mm) Then insert 2 of these expanding tube ends. They require 2x M5...

Print Settings Printer: Folger Tech 2020 Prusa i3 Rafts: No Supports: No Resolution: 0.2 Infill: I used 30% infill for strength. Notes: I tap the 2020 insert with an M3 tap after printing, but you should also be able to self-tap it with an M3 bolt....

The Shapeoko lift blocks offer an extra 20mm of height to your CNC machine, enabling you to add materials from the side without having to remove it from the waste board. This increases clearance from motor plates by 35mm. I printed these using 40%...

File#1: BulbCalibrationBox.STL: Basic box for you to fill with the material you are going to use for your bulb. This is more for people wanting to fill a printed shell with something like lead-shot. If the calibration box was filled with a solid...

I started off trying to use the level blocks over at TH3D but those were not tall enough and were causing my hot end or fan to hit the bed.. So I decided to just go ahead and make some longer ones.. they seem to work well so thought I would share...

This is a remix from: https://www.thingiverse.com/thing:3020026 Modified mount to fit in the FLSUN SR top arm. Modified roller guide at a height of 44 mm. Print Settings Printer: any Rafts: No Supports: Yes Resolution: 0.12 - 0.2 Infill: 40% - 50%...

This is a small filament guide with roller bearings to sit atop the Prusa printer frame to guide filament into the extruder with minimal friction. Print instructionsPrinted with 0.20mm layer heights, 0.45mm extrusion width, 2 perimeters, although any...

I added skates to @K4mi1 's bottom piece so that the G203 mouse skates can be reused.

Print 4 of these 90°Corner Blocks to create your own cheap Corner Band Clamp that you can use with any ratchet strap.Despite the previous modification by manuelmasc, the 3 supports still seemed too weak to me, so I made them thicker again and...

This is an automatic machine for filling liquids into bottles

Pillow block for 608 type skate bearing, slightly modified from http://www.thingiverse.com/thing:217391 changing mounting hole spacing, and overall thickness. 7 mm thick bearing sits on 2 mm lip and other face is flush with block surface. These...

You can print one large box that includes all three grits plus leather strops, or you can opt for a single box that holds just one pair of stones. These boxes were designed using Fusion 360. The entire box took around nine hours to print on my...

I searched for that part, since i ruined my original. it was nowhere to buy, so i made it myself. you need a velcro pad with a with of 5 cm. ...its tested and it works.

remix for ender3 v2

... not look pretty, but it's better safe than sorry. Printer Settings: XYZ Da Vinci: Rafts: Enabled Supports: Yes Resolution: 0.2mm Infill: 10% to 20% Notes: A raft is not strictly necessary, but it's a good idea to include one for added stability.

testpin for CrushGrind Diamond MINImessurements in photo abovethe groove is 5x5mmOn the testpin the pins on both sides are positioned 1mm towards the opening compared to the exact distances of the parts - so slightliy loose fit should be perfect ;-)...

Rollerblades for 3D Transportation on Sketchfab

For use with 73mm filament spools, commonly black in color.

Spool Rewind adapter. ...Designed for 4mm screws. Print 3 posts with size you need, but subtract some mm for tight fit.

A clever approach to an essential part for sliding door mechanisms.