half pint of paint 3d models
2899630 3d models found related to half pint of paint.thingiverse
I only made one for the back half of the Onewheel since it makes no sense to protect the front half. After all, the front half is integrated with the front bumper and should be replaced whenever the front bumper is worn. The back half can take...
thingiverse
Voici un mi-fender pour la Pint ! Je l'ai déjà utilisé sur la mienne et le 3D est nickel ! Ce fender est renforcé au niveau de la base. Si votre machine 3D est trop petite, faite le en deux parties et collez les ensembles. N'hésitez pas à me...
cults3d
Pint of beer for 70 mm bottle (If you want other diameters contact me) On this pint, there are two rings to count the number of beer drunk. From 1 to 99 ;). This model is composed of four parts. ...(the counting ring is to be printed twice) 1) Print...
prusaprinters
We have a set of Half Pint milk bottle glasses with straws that has protected our home from many spills through yeas of toddlers and are still often being used as they are preferred by the kids. The original lids split and I couldn't find...
myminifactory
This is a 1:1 scale model of a pint sized half and half carton commonly found in the US. It has threads on the spout, but the cap from an actual half and half container doesn't screw on properly. (That was the goal, however.) Still looks good. The...
thingiverse
Customized version of https://www.thingiverse.com/thing:619626 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=619626
thingiverse
Customized version of https://www.thingiverse.com/thing:739573 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=739573
thingiverse
Instructions The glass part of a wide mouth Mason or Ball canning jar has a 0.25 inch pitch single turn thread with a base diameter of approx 2.63 inches. A minimum side wall thickess of about .060 was chosen to insure a robust abaility to torque it...
thingiverse
After various experiments I settled on a wall thickness of .060 in thickness (1.5mm) as a good balance between sturdiness and the amount of the filament used. A thin wash of Acetone will seal the surfaces nicely. ABS Printing was performed at...
thingiverse
I've created and included some key elements to make it usable: -L Quarter -L High Quarter -L Snowplow Quarter -L Flat -S High Quarter -S High Bank -S Flat -2 pack of connector pieces I really hope you enjoy. Tested and have been through a few...
thingiverse
Customized version of https://www.thingiverse.com/thing:619626 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=619626
cgstudio
Photorealistic and High Detailed Pint of Beer Collection.12 Glasses and 4 coasters.Formats :Max2009 V-rayMax2009 scanlineObjFbx3ds*V-ray materials and default scanline materials included in all...
thingiverse
I decided to make the hammer split in half for two reason one comfort and two because of Thor Ragnarok. Its comfortable because of it's flat side it allows the printer to place it face down on a desk or wall and have the hammer extrude through the...
thingiverse
... to use. Check my math. This component is part of an open source lab library, by the Michigan Tech's Open Sustainability Technology Research Group. ... For similar see the Open-Source Lab How to Build Your Own Hardware and Reduce Research Costs
sketchfab
Experimenting with baking lights and shadows. ...Low Poly interior inside torn of fragment of the apartment. 8,9K faces. The largest texture (4K) on the walls, other textures are around 1-2K. ...Best viewed with HD textures.
thingiverse
Customized version of http://www.thingiverse.com/thing:305087 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=305087 Instructions Using the following options:...
thingiverse
All of the other designs are hours and hours, tons of wasted plastic and you have to keep the door off. Prints in 39 minutes. Super minimal design.... did I mention you can keep your door on? I would like to add two little tiny filament...
thingiverse
This is the output side of the drive coupling on a Mi-T-M pressure washer. The gasoline engine supplies mechanical power to the fuel pump on the diesel burner side and this coupling is integral to that. The Mi-T-M pressure washer is model number:...
cgstudio
(included color, bump, reflect and refract maps)One pint of beer :1.550 polygons9.758 polygons (Turbosmooth 1 iterations)*******************************************Detailed enough for close-up renders.JoseVKPrice: $20.00 Date added: Feb 04, 2015Last...
cgstudio
(included color, bump, reflect and refract maps)One pint of beer :974 polygons5.150 polygons (Turbosmooth 1 iterations)*******************************************Detailed enough for close-up renders.JoseVKPrice: $19.00 Date added: Feb 04, 2015Last...
cgstudio
(included color, bump, reflect and refract maps)One pint of beer :1.900 polygons10.108 polygons (Turbosmooth 1 iterations)*******************************************Detailed enough for close-up renders.JoseVKPrice: $21.00 Date added: Feb 04, 2015Last...
cgstudio
(included color, bump, reflect and refract maps)One pint of beer :1.390 polygons5.326 polygons (Turbosmooth 1 iterations)*******************************************Detailed enough for close-up renders.JoseVKPrice: $19.00 Date added: Feb 05, 2015Last...
cgstudio
(included color, bump, reflect and refract maps)-Polycount :One pint of beer : 1.900 polygons10.108 polygons (Turbosmooth 1 iterations)Chips and bowl : 11.422 polygons.*******************************************Detailed enough for close-up...
cgtrader
included color, bump, reflect and refract maps-Polycount :One pint of beer : 1.900 polygons10.108 polygons Turbosmooth 1 iterationsChips and bowl : 11.422 polygons.*******************************************Detailed enough for close-up renders.JoseVK...