harbor freight cordless drill 3d models
63128 3d models found related to harbor freight cordless drill.thingiverse
I originally employed a Harbor Freight cordless drills for drives on both sides of my 12 lb bot, as well as the weapon lift. You can use the stock gearbox housing, but it is only bushing supported, and would therefore require periodic greasing to...
grabcad
Motor and connected gearbox from Harbor Freight 900rpm 18V cordless drill. ... Model #RS-550S-18V
thingiverse
These are mounts for the motor used in the Harbor Freight cordless drill Item #68239. These are often on sale for $15.99. These run great on a 12V battery, like the one you might put in your next robot. Instructions Buy the cordless drill from...
prusaprinters
I was sick of the crappy, cracked case that came with my cheap Harbor Freight drill bits, so I decided to make a slightly less crappy holder for them. Remove the 3 orange pieces inside, cut off the excess on the sides, and shove them in here for...
thingiverse
This is a drill bit holder for the harbor freight drill bit set with 1/4" hex drive. It can hold any 1/4" drive bits or tools, up to thirteen (13). I use slic3r for my slicer. ... Enjoy.
thingiverse
I broke my switch cover and needed a new one. ... I printed the source file and found it way too big. HF Item number 38144 13" Drill press
thingiverse
This is a basic holder for a Harbor Freight 20v drill. ...
thingiverse
Flange mount for motor and gearbox 18v Lithium Warrior Harbor Freight drill to be mounted for a robot.
thingiverse
in the works......... ...This is a replacement for the factory depth stop for the bench-top harbor freight drill press.. ...also has additional hole for accessories..
cults3d
in the works......... ...This is a replacement for the factory depth stop for the bench-top harbor freight drill press.. ...also has additional hole for accessories..
thingiverse
I remixed this Drill Index https://www.thingiverse.com/thing:1769954 to fit this Harbor Freight 7pc Brad Point Drill Bit set https://www.harborfreight.com/brad-point-wood-drill-bit-set-7-pc-61640.html
cults3d
Chuck Key Holder for my Harbor Freight tiny Drill Press. Clamps around the main support column. Uses x2 4-40 pressed inserts and x2 4-40 screws. ... Printed with PETG filament.
thingiverse
Chuck Key Holder for my Harbor Freight tiny Drill Press. Clamps around the main support column. Uses x2 4-40 pressed inserts and x2 4-40 screws. ... Printed with PETG filament.
cults3d
Hardware: (Qty 1) M5 x 16mm Cap Screw (Button Head Cap / Phillips Head is preferred) (Qty 1) M5 nut Guide Buying Options: - Maker86 Industries Listing: https://maker86.com/shop/ols/products/rotary-tool-guide-compatible-w-harbor-freight-drill-master...
thingiverse
This a fairly simple flange mount for a harvested motor from a discount drill from Harbor Freight. I made this mount, along with the rear strap, to mount 4 motors on a lightweight robot platform. ... ...
thingiverse
This is a simple Rotary Guide that fits the $10 Harbor Freight Drill Master (63235). It was designed for people doing extruded polystyrene carving... aka Tombstone carving. Hardware: (Qty 1) M5 x 16mm Cap Screw (Button Head Cap / Phillips Head...
thingiverse
While moving my older Harbor Freight floor drill press to my new workshop, I broke the front panel that holds the power switch and light switch. Several years in the Texas heat had made the plastic very brittle, and it broke at every attachment...
cults3d
While moving my older Harbor Freight floor drill press to my new workshop, I broke the front panel that holds the power switch and light switch. Several years in the Texas heat had made the plastic very brittle, and it broke at every attachment...
cults3d
Includes 2x Drill Guides - 1 for Pigtails and 1 for Ethernet and Power Glands Holes sizes are for 1/8" Drill Bit, then use a step bit to the correct size of your glands
thingiverse
I wanted a guide for my drill press in order to get my holes centered on a pipe. ... Nothing fancy but it seems to do the trick.
thingiverse
Here is the original project https://www.thingiverse.com/thing:2761685 I originally employed a Harbor Freight cordless drills for drives on both sides of my 12 lb bot, as well as the weapon lift. You can use the stock gearbox housing, but it is only...
thingiverse
This is a replacement power switch cover for a Harbor Freight/Central Machinery 8" Drill Press. It was a very snug fit into the plastic enclosure. ... You might want to downsize to 99%.
thingiverse
Harbor Freight's Masonry Drill Bit Set 5 Pc Holder with Marks for the correct size. 3/16 in; 1/4 in; 5/16 in; 3/8 in; 1/2 in. ... Printed with leftover Glow in the Dark PLA
thingiverse
This is a magnetic bit holder for a Harbor Freight Bauer 20V drill or driver. It uses two 8x2mm round magnets that you must glue in. ...The holder has two 15mm deep hex slots for shorter bits and can hold a long bit or drill bit on the outside.
thingiverse
First day I had my hand-me-down bench-to Harbor Freight drill press I carelessly snapped the plastic depth stop collar. In a jiffy using FreeCAD, I was able to model a new one and have it printed out. ...Let me know if there is anything that needs...
youmagine
The bubble-pack these bits came in isn't a great toolbox carrier for 'em, and they're so small, they get lost very easily. ... This small sliding drawer box has a friction-stop when closed. It fits the Harbor Freight 61526 drill bits pretty well.
thingiverse
... in the best print orientation. The upper parts are provided inverted for the way that they will be used when mounting the rotary tool. [Harbor Freight Drill Master Rotary Tool](https://www.harborfreight.com/rotary-tool-kit-80-pc-63235.html)
thingiverse
... chord as neither is intended to be removed post installation. UPDATE: I made a version of this to fit the larger key and thicker cable of the Harbor Freight 1/2" hammer drill. ... That's available at: https://www.thingiverse.com/thing:4982819
thingiverse
This is a replacement chuck key holder/keeper for the Harbor Freight Chicago Electric 1/2" hammer drill. The current SKU's for this drill are 62383, 45338, 67616, 68169, and 60495. This is a remix of the chuck key holder I made for the Harbor...
thingiverse
The vise grip style drill press clamps available from Harbor Freight (and perhaps elsewhere) are really handy, but they will mar softer materials like aluminum. I didn't want the surface of the piece I was drilling to have marks left on it by the...