hc models

In order to ensure that the 2 rhombi are assembled correctly, there are 2 different tabs built into the edges of my models. This ensures that they'll only ever be joined correctly! Also, the strips make it visually clear how to assemble them.</p>...

No support is needed and would be very hard to remove because the support would be inside the model where the magnet eventually slides into. We are depending on bridging for the parts that would normally need support. I have given extra tolerance...

I sliced it with Cura 4.4 so you can use per model settings to print the whole thing at once. I printed it at .15mm layer height.</p> <p>Here's a video of the toy with some details. ...The video has a lot of assembly photos at the end.<br/> <figure...

I sliced it with Cura 4.4 so you can use per model settings to print the whole thing at once. I printed it at .15mm layer height. Here's a video of the toy with some details. The video has a lot of assembly photos at the...

You can find a somewhat more detailed list of supplies in my Instructable at https://www.instructables.com/Kissing-the-Frog-V20-Back-Horn-Bluetooth-Speaker-F/ Basically any combination will do (as long as the driver is 3.3" or smaller so it fits the...

I modeled the general design of these connectors after Spears brand Dri-Splice connectors (http://parts.spearsmfg.com/sourcebook/TURFTECH_TURF_IRRIGA_T_TURF_DIR_T.pdf). Most of the good professional landscape light and outdoor audio companies in my...

Keep weight and cooling considerations in mind if using an alternate - ESC: Water proof ESC appropriately rated for your motor / battery combo - Cooling Nipple: M4 X L15 https://www.aliexpress.com/item/32614416689.html - Cooling Tube: 4 mm I.D 7 mm...

I created this project to get more experience in modelling for 3D printing using Fusion 360, practice my soldering skills, and get a chance to do a little ESP8266/Arduino programming. *Features* hang it from the wall using the built in hole(s) or...

I use washers between the skate bearing and the mount to give a little clearance for the spool holder to turn (I could probably model in a little bump out instead of using washers).For adjustable friction, I've added a simple bail that attaches to...

The attached model is sized to fit the Eye Cu Smile V2 and V1 filter housings at 45 mm OD and 10.5mm high However if you want to make any size antimicrobial / antiviral filter meshes for any purpose then even sketchup will suffice Steps to draw a...

If you need a lot more room (more than a few mm) you may need to update the model to scale it appropriately. (~$1 of filament)</li> </ol> <ol> <li>Light string or rope. Cut it about 5ft 6 inches, or just enough to make a loop on the elbows, running...

The retainer is up higher than need be in the video for safety.--------------------------------------------------------------------------------------------------------------All parts printed in PETG, with standard Voron settings for rigidity.0.20...

Also, no screws or other fixing methods are used. How it works can be seen in the video UPD I added a version in two sides in the form of frames, its printing a third faster and when printing a model, corners closed by cooling by a fan are not...

Two B2s stacked works well for going higher.Related Links: Magnet Insertion Tools for Bases Drilling Guide and Magnet Insertion Tools for Walls Door Frame Adapter for rbross DoorsCompatibilityThe short tiles (Row A and Column 1) are also compatible...

# Introduction This is a remix of the Ender 3 HallON v3 Installation kit to fit a Micro Swiss Direct Drive set-up (recent models with additional screw holes on the left. Because I noticed that the hold of the sensor in the adapter gets loose after...

If you want to use the hardware I intended this to use: Hinges Bolts- https://www.mcmaster.com/91292A018/ (you will need to thread inner most hinge) Hinge spacer- https://www.mcmaster.com/91755A311/ (you can see in the photos a little bit of white in...

While his drinking-glass method worked for me, I could not get the parts of his model to fit together well, because my printer does not appear to be tuned well enough. Note that the guide is all Denny's work, refined by him in many months. My...

The shoe lace is optional but it's a good way to secure the handle from unfolding when you don't use it.Print SettingsDon't rotate the models when placing them in your slicer. I have placed the parts in the best orientation possible with surface...

Verify the axle turns freely. Source File FreeCAD: BearingPegV4_2019.FCSTD Reinforced Within the pegs (excluding the original V4) 'pins' are embedded that promotes a strong cross pattern with lines at the stress point in addition to beveling....

Every link piece adds roughly 2,5 cm or 1 inch. Step eight:Cut Filament to 2,3 cm and attach the body strap to Piece K connector strap. Step nine:Cut again Filament to 2,3 cm and attach the N handles to M handle attachment:Congratulation, you just...

Luckily, this model is not in tune anyway lol. Post-Printing Even at 0.06mm and surface-oriented settings, I have found that the interior surface of 3d printed woodwinds is still not smooth enough to get a really good timbre. To fix it, you could...

Update 2021/02/06: Upgraded parts- steering arm 2.0 Bump steer reduce for steering knuckle 2.0(the ackermann angle have been reduce on steering knuckle 2.0 and therefore with the change of geometry this part is required to reduce bump steer) Update...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: use_pattern = 1 custom_corner_resolution = 8 stencil_drawing =...

4028 fan mount: Note this is modelled with internal supports in the top section of the duct to make it easier to print. Please remove these supports after printing. 4 x M3 32 mm (upper fan mount) 2 x M3 x 12 mm cap screws (lower fan mount) 6 x M3...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: use_pattern = 1 custom_corner_resolution = 8 stencil_drawing =...

... self sustaining for long periods. All ground piping, cabling and the Large Gas collection cansiters would be covered in Dirt once operational for Sun / wind shielding. Note the Space Suit man was inserted for size, got it from the NASA models site

Your purge block will be rather large, so if you have a suitable item you can use as a wipe model, use it! Then, remove the 8 outer-most parts and core, leaving just the inner 9 components. You will need to reassign colours, i.e. red becomes the...

If you have a tuned in printer, bump the speeds up a little for a dramatic improvement, (make sure wall thickness is a multiplier of your nozzle thickness - The parameters are important and there are a lot of dependencies, Make sure you have done the...

18-48V AC/DC voltage models are available for network systems and marine vessels. We also offer an additional 120-277V and 347V high voltage, 125-250V DC, and 0-10V dimmable versions of this explosion proof LED light fixture.Wiring: These LED light...

The problem is that the individual mirror cells overlap and when I separated the cells into parts of the larger array, each cell along the perimenter got the full width base perimeter border and so they bump up against each other instead of...