hd lifecam 3d models
16867 3d models found related to hd lifecam.grabcad
Microsoft LifeCam HD, 30FPS, Wide Angle F/2.0 Lens, 720p, Autofocus. Model # 6CH-00001. ...Commonly used as a webcam.
thingiverse
This is Mount for the Microsoft Lifecam HD Webcam. I was not able to find something which was easily detachable. So I created this mount as a 3 piece design. This is a Work in Progress. I used the glue to attach the backplate but the rest of the...
thingiverse
This clip provides secure mounting for the LifeCam HD-3000 camera. You'll need to remove the floppy rubber-covered bracket by either opening up the camera and fiddling with impossibly tiny screws, or do like I did and cut the thing off with a...
prusaprinters
Mounting bracket for Microsoft LifeCam HD 3000. Ideal for mounting camera under the top IKEA lack desk. For assembly one M2 x 20 Screw and one M2 Nut is needed. Print instructionsBottom part can be printed without support. Top Part was printed with...
prusaprinters
... 2020 extrusion. Add as many of the 2 arms as you need to get your desired position/angle. It's all held together by some M3x25 screws. Original mount: https://www.printables.com/model/266287-prusa-mini-webcam-bracket-microsoft-lifecam-hd-300
thingiverse
Additional requirements: Microsoft Lifecam HD-3000 OctoPrint with a free USB port The original housing of the Lifecam HD-3000 will be removed and destroyed, the four screws will be re-used. Opening the original case (see picture): Unlock the two...
thingiverse
Some basic files to hard mount a Lifecam HD-3000 on your robot. Can be used for the camera alone, or add a high power LED on a heatsink. (Details still TBD, but see the notes section.) Also on Github: https://github.com/Techbrick/Electronics-CAD...
prusaprinters
This clip provides secure mounting for the LifeCam HD-3000 camera. ...You'll need to remove the floppy rubber-covered bracket by either opening up the camera and fiddling with impossibly tiny screws, or do like I did and cut the thing off with a Dremel...
thingiverse
A custom top piece for Microsoft HD cam, original: https://www.thingiverse.com/thing:3223979
grabcad
A printable articulated support for lifecam.The pivot shaft is mounted with a 4mm screw (approx 5/32 in)
thingiverse
Simple wall mount for Microsoft LifeCam HD-5000. ...
thingiverse
This disabled the video funktion by close the cam hole. ... I use it the most time as a microphone. Designed for Microsoft LifeCam HD-3000 ;) Rotate X --> 90° Thanks, Enjoy! ...
thingiverse
This is a very simple camera mount for Anet A8 and Microsoft Lifecam HD-3000. ...The mount features an adjustable slider for height of the camera and adjustable Yaw rotation of the camera.
thingiverse
Adjustable Height Base for MS Lifecam HD 3000 Print Settings Printer Brand: Printrbot Rafts: Doesn't Matter Supports: Doesn't Matter Notes: Print the pin slow!, I printed at 10 mm/s, the rest at 50 mm/s, print base with good fill % (around 80%)
thingiverse
handy tripod support for MICROSOFT LIFECAM HD-3000 Better version remixed by dmarc73 herehttps://www.thingiverse.com/thing:2917065 Print Settings Printer Brand: Prusa Printer: Prusa Mk2 Rafts: No Supports: Yes Notes: the hole do not have the...
thingiverse
Bed support for the camera Microsoft Lifecam HD-3000. It can be installed without any screw or clamp on the side of the hotbed. ... Tested on FlyingBear Ghost 5 **Please share Makes and feedback.** **If you liked it consider for a donation.**
thingiverse
Use three 1/4" bolts to secure a Microsoft Lifecam HD 3000 webcam into this cage. The tabs on the back are designed to work with my Linkos mounting system, which also uses 1/4" bolts. ...With this, you should be able to securely position this webcam in...
thingiverse
Mount designed to hold the Microsoft LifeCam HD-3000 inside the Flashforge dreamer on the front left side, 4 x 2.5M screws required to hold everything in place. Main mount doesn't need support, but would recommend support for the wire manager. ... ...
thingiverse
The LifeCam clips are modified from LoboCNC's LifeCam HD-3000 Mounting Bracket (https://www.thingiverse.com/thing:2126754) but the camera slides in from the side so that the rubber mount doesn't need to be removed. Although the surface on the clip is...
prusaprinters
Bed support for the camera Microsoft Lifecam HD-3000. It can be installed without any screw or clamp on the side of the hotbed. Tested on FlyingBear Ghost 5 Please share Makes and feedback. If you liked it consider for a donation. Print Settings...
thingiverse
What you need : 1x Microsoft LifeCam HD-3000 2x M3x12 screw 2x small cable tie Printed parts :-) Printing : - The STL files are oriented the way I think it print best. - 0.4 nozzle, - 0.2 mm resolution, - infill 100% - Support is needed. - I...
prusaprinters
I designed this webcam mount to mount my Microsoft LifeCam HD-3000 into my printer enclosure. It is designed to be installed to one of the IKEA LACK table's hollow legs.</p><p><strong>Installation:</strong></p><ol><li>Drill a 2cm hole into the LACK's...
thingiverse
This is a simple but effective cover for microsoft's hd-3000 webcams. ...
thingiverse
Somebody donated a Microsoft LifeCam without a mount, so I designed this mount. Seems to work pretty well. The camera base can drop into the hole one end at time, then bring it back up flush. A tiny ledge should hold it in place. ... The...
prusaprinters
... the hole. If it's too loose, try adding some super glue on the outside of the nut to hold it in.Check the original for instructions on how to properly disassemble the Lifecam to remove the stand and fit it on the mount. Category: Camera
thingiverse
Simple bracket to attach Hd-3000 webcam to 6mm framed 3d printer (or, well, whatever you like that is 6mm thick really). ... I used the instructions here to open camera and replace stock bracket:...
thingiverse
I have also included an earlier mount that I used which does not require taking the LifeCam apart to change the bracket. Google on how to take it apart, it's not difficult, just a bit fiddly. Print Settings Printer: Malyan...
thingiverse
Simple bracket to attach Hd-3000 webcam to upright towe on the Rostock Max v2. I used the instructions here to open camera and replace stock bracket: https://astrophotovideo.wordpress.com/adapting-a-webcam-to-a-telescope/ You'll also need: 1x m3x30...