heltec 3d models

This is a version of Tinderbox with box and software modified to use Heltec's ESP32 Module with integrated OLED display and battery management. It all works off of a single Lithium Ion cell. For battery power I needed to add a switch for on and off (...

For designing an appropriate enclosure, consider using the precise replica of the Heltec WiFi Kit 32 - a highly reliable device.

Enclosure for Heltec LORA v2 ESP32. It allows to do range test easily. ... I suggest you to use transparent material so you can see onboard leds.

Hi, this is a Remix of the Case who is original fittet for the "Heltec CubeCell-GPS HTCC-AB02S Board" Now it fitts for the Heltec V1 Board. Some issue to fix high of the case, the SMA connector lifts the top cover a little bit. ... If you want you...

Hi, this is a Remix of https://www.thingiverse.com/thing:4649316 Now it fit´s with a Heltec V1 Boardand a 120mAh battery. ... If you want you can support me with a small tip

... silly.  The Heltec is a friction fit in the case.  Sanding the sides of the heltec will make installing much easier.  Lid slides in case and secures with  3m screw 5mm long. PRINTS WITH NO SUPPORTS. ...Holds 2kmah battery size 50mm x 34mm x 10mm.

Case for Lora Heltec ESP32 + DHT11 Board Description: This is a compact case designed to house the LoRa Heltec ESP32 and DHT11 sensor board, a highly efficient and versatile system used in IoT applications. The case offers protection and organization...

Case for Heltec ESP32 LoRa - The Ultimate Long Version. You Can Even Add a Relay, Temperature Sensor, and Battery! Want to take your Heltec ESP32 LoRa project to the next level? Look no further! This case is designed to be the ultimate solution for...

This is a prime opportunity to showcase the capabilities of the Heltec ESP32 LoRa or WiFi development board. ... To get started, watch this comprehensive installation guide: https://www.youtube.com/watch?v=427LyOoTNWc - it's perfect for those who want...

To create an efficient enclosure for the Heltec WiFi Kit 8, it's crucial to have a precise model in hand. ...This model provides necessary details about the device's dimensions and features, ensuring a well-fitted case that safeguards its functionality.

I designed a case specifically for the Heltec LoRa 32 V2 board, tailored to be used with the Meshtastic project. ... https://www.meshtastic.org/ The required components include: 4x m3x20 socket head cap screws 4x m3 nuts 1x Heltec LoRa 32 (V2)...

The primary electronics are housed in an Heltec LoRa ESP32 board and a Hall Effect sensor. For a complete parts list, click here. ... The software, documentation, and schematics can be accessed on my GitHub page:...

Case for the Heltec 8S capacitance balancer. Allows you to protect the balancer & screw it to a surface to hold it in place. Printed in ASA for heat tolerance, set the outer layers to 10 to make the screw columns solid, otherwise no supports or...

Generally I recommend not to use inserts, unless you know that you are going to open the case frequently.AssemblyMelt the four inserts into the bottom part (if applicable).Connect the antenna cable to the Heltec module.Put the Heltec module into the...

I got these cheap Heltec boards to play around with meshtastic. Don't know what meshtastic is? Check it out at https://meshtastic.org/ I wanted to make these as compact as possible. I designed this case. It has just enough room for the board...

Upon the initial boot of the Heltec node, you may encounter a message saying "Canned Message Module Disable." Simply press the reset button, and the node should boot correctly, allowing you to begin typing.Additional Information: Whenever you...

Also leaves you with the option of discarding the reset button if needed. I got these cheap Heltec boards to play around with meshtastic. Don't know what meshtastic is? Check it out at <a href="https://meshtastic.org/">https://meshtastic.org/</a></p>...

This is a minimalist case for the Heltec Wireless Tracker. I have remove the antenna cover to integrate it into the housing. I like to have a physical power switch as well, but if folks dont want that I can make a variant that removes it. Enjoy!This...

LoRa module transceiverManufacturer : Heltec

A Case for Heltec ESP32 LoRa

Very simple holder for my for my Meshtastic Heltec wifilora 32 with the original Heltec Shell.For mounting you need 2x 3mm countersunk screws.

The is a case for the Heltec LoRa32 V2 / V3 module.This is part of a larger project that includes home automation sensors: Heltec LoRa32 Door sensor.

Modified the Heltec WiFi Kit 32 model (Heltec WiFi Kit 32) 1) Converted surfaces to solids2) Inserted a better OLED model.

Modified case to support v1.1 of the Heltec-GPS board

Case for Heltec LoRa 32 radio. Designed to fit 1100 mAh battery. ...Uses three m2.5x20mm screws.

This case was designed for the Heltec WiFi LoRa card to be used at the FIT event held by the University of Galileo in 2018.

This housing replaces the std. ...clsoure plate to be able to mount the Heltec WiFi Kit 32 to the std CG-Scale.

for heltec wifi kit 32(v3) it's necesary to remove a piece because tyhe usb-c is bigger than micro usb

Designed in OnShape: https://cad.onshape.com/documents/adbca6d97823a7cd3a33f571/w/93365e6c51e1c3a032b4445d/e/c91587cc1bf0a242e01a9f32 More info about the board: http://www.heltec.cn/project/wifi-lora-32/?lang=en...

It's more affordable, features an elegant E-ink display, and consumes less power.Details:Board: Heltec Wireless Paperhttps://heltec.org/project/wireless-paper/ $14.90 + Shippinghttps://www.aliexpress.us/item/3256805461611876.html?channel=twinner...