hemera part cooling fan 3d models

This bracket secures the cooling fan assembly, directing airflow more efficiently towards the printed item. To optimize performance, there's no requirement to alter the fan duct. ...Simply use a longer screw located at the bottom for secure attachment.

Alternative part cooling fan duct for Geeetech A10. Supplied fan, in my opinion, is woefully inadequate. Standard 24V 40x40x20 fan paired with this duct has proven itself to be a superior solution for me. In the provided blender file, there are three...

This minimalist design utilizes a standard 30 mm fan and securely attaches to the right side of the heat sink's cooling fan using longer screws. ...The duct is specifically tailored for volcano-style hot ends but can also be adapted to fit most printers...

I made this dodgy part cooling fan to be compatible with this E3D mount for the Ender 5 -https://www.thingiverse.com/thing:3682669 because I like the lightweight construction. While it is very much not a finished design it works and did okay in my...

Simple direct replacement part for an improved part cooling effect. It's based on the tusk type of part cooling. Two small aluminium tubes are held by a plastic holder that forces all the air from the radial fan into the tubes. There are small holes...

A bespoke cooling fan system tailored specifically for the FT I3 Mega, cleverly reimagined from "Folger i3 2020 Print Cooling Fan Assembly" by pjvpjv, featuring a deliberate mirror image of all components to the left side and an innovative new...

... heat sink cooling for stock hotend of the raise3d n2 series. ...Designed for a noctua 40x10mm 12v fan. https://www.amazon.com/Noctua-Cooling-Blades-Bearing-NF-A4x10/dp/B009NQLT0M/ref=sr_1_3?dchild=1&keywords=noctua+40mm+fan+12v&qid=1631122389&sr=8-3

You will need to get a 5015 fan to fit the part cooling, the blower fan is going to fit, but I changed it too. Also you will need to get rid of the original "cave" wich is easily done by removing the 2 screws at the top. I also uploaded a simple...

This is a quick remix I did for my CR10-V3 for part cooling with my Klemco mount as I found the already avalible mounts from Klemco to be insufficient for what I needed as I needed cooling from both sides with minimal hardware. This is the first...

These custom cooling fan ducts replace the factory part on the LEO, providing superior airflow to the nozzle. The original ducts may look well-made, but they fail miserably in their cooling duties, simply blowing air at the heater block and behind...

This is a quick remix I did for my CR10-V3 for part cooling with my Klemco mount as I found the already avalible mounts from Klemco to be insufficient for what I needed as I needed cooling from both sides with minimal hardware. This is the first...

Original Model: BIQU H2 Extruder Fan Mount & Fan Duct(Version 2.0)Made by: Schwab_Manufacturing_Solutions While I liked the reinforcements and increased adjustability in positioning, I found that the original still did not fit my own H2...

I designed a cooling fan specifically for Tevo Tarantula when paired with my E3DV6 Carriage and an E3dv6 hotend. The duct features a small internal baffle, which enables the air to circulate efficiently throughout the duct rather than just flowing...

Forum Discussion: https://forum.raise3d.com/viewtopic.php?f=20&t=21427&sid=0d145d9e3416a285fa33cc6923b925bb Here is the cooling fan shroud STL for the right extruder. Mirror it for the left one. The aesthetic shroud that comes with the extruder does...

You can also use this mount to install a radial fan for part cooling. The fan mounting parts were designed with one particular fan in mind (https://www.amazon.com/gp/product/B01K49K358) but should work with any similar-sized fan. To assemble the...

... within the limitations of a single 4010 fan (now running a 5015 with a different duct.) It is noticeably better than the factory ender duct and as good or better than a few others I have tried. ...Good job to the creator of the original part.

Human: I remixed Ender 2 cooling fan 5015. You can find my original design on Thingiverse at https://www.thingiverse.com/thing:2780652. To improve stability, I added holes for screw mounting instead of relying on double-sided tape, which kept falling...

Remixed from: Ender 2 cooling fan 5015 https://www.thingiverse.com/thing:2780652 Add holes for it to be fixed with screws instead of double sided tape (mine kept falling because of the temperature). ...Also added a hole for a M3 insert to be easier to...

Here's a high-performance, 270-degree cooling fan duct designed specifically for the Monoprice Maker Select V2. This innovative solution doesn't require any additional nuts or bolts to install. ...The fan utilized in this setup can be found here:...

To ensure efficient cooling, the fan is securely attached to the hotend carriage next to the existing hotend cooling fan using a sturdy fastener. The duct itself fits snugly onto the shoulders to prevent any accidental over-insertion. This upgraded...

This design uses the existing mounting plate and a single M3 screw to attach, which secures the cooling fan duct directly to the mounting plate. The original concept is based on a great design by lorddeus, known as the TronXY X5S Cooler, posted on...

... temperature steady. It does happen however, that with the addition of this cooling fan to keep things under control, that it may become a bit of an issue since its just a bit too strong, resulting sometimes on small drops when you flip the switch.

compact part cooling fan duct for the biqu h2 extruder. for 40mm fans so you could use the original ender hot end hardware, even the screws. this is the first version though so i might update if it doesn't perform good enough. printed with the fan...

This part printed in PETG will fit and clear all parts and provided much better cooling, less stringing and over hangs look great now. one picture shows the factory part cooling duct next to the new design, you can see how much farther back the new...

Using CarstenD's 'Creality Ender 3 part cooling fan duct' as inspiration (https://www.thingiverse.com/thing:3091300), I designed a Part Cooling Fan Duct for the Ender 5. This design far exceeds standard or small fan ducts when printing ABS, forcing...

Part cooling fan shroud for the Artillery Sidewinder X1... Wanted something small, lightweight and semi-circular. This is a remix of this <a href="https://www.thingiverse.com/thing:3923283">https://www.thingiverse.com/thing:3923283</a> which is a...

A part cooling fan for NF Sunrise extruder using a V6 block, it should be easy to convert for use with a Volcano. I haven't got my bridging settings dialled in so I've added models with internal supports which may or may not work for you. There's...

The part cooling fan remains unconnected, awaiting wiring, while the rest of the system operates smoothly. A nozzle to direct airflow towards the print is still required for optimal performance. To avoid print head interference, remember to add a...

It would be a good idea to add this as part of a custom splitter cable to split the part cooling fan power leads for the new fan. (Fan 1 on toolhead 2.0) I got my diode as part of a pack, and used some JST connectors to make the splitter. Solder the...

It would be a good idea to add this as part of a custom splitter cable to split the part cooling fan power leads for the new fan. (Fan 1 on toolhead 2.0) I got my diode as part of a pack, and used some JST connectors to make the splitter. Solder the...