hmip mod oc8 3d models

More info: https://all3dp.com/2/combing-mode-cura-simply-explained/Below: needle threader with other things for scaleBelow: various prototypes (rightmost is current model)Reference printI like printing fairly clear and dense PETG...

Once assembled, you can slide in the necessary tool holders and extend the unit further by linking them with the mod stick. Since my replacement printer has not yet arrived, I am unable to test this setup at present. However, I would advise against...

We have made several mods to come up with this re-design. The first thing you will find is that we have created our own headband. These will come in two sizes. One is for youth and will squeeze a little tighter to the head to give it more grip...

Note that some of the design elements are actually mods from my original A8, so parts to this design can be found on their own page. This following will include the link and mention any updates to those parts: - X/Y bearings and bearing blocks:...

I share model files used for mini bear.Some of the MK3s Bear models have been modified to fit Prusa Mini.https://github.com/gregsaun/prusa_i3_bear_upgradePlease refer to Prusa Bear Github for assembly...

It draws 0,07A at 12V with a higher flow rate of 64,6m³/h and a noise level of only 17,1dB(A), it also comes with two low noise adapters where the "small" one would half the rpm to a similar flow rate of 51,1m³/h at 11,6dB(A).What you need4 printed...

I'll upload the file for the spiked wheel and pictures of the modded pillars to give you an idea of what to do. But overall, I'm happy with the result because instead of having to rescue the robot during its mowing mission every day, this has come...

It is compatible with kp3s pro and kp3s pro S1 Attached you can find the assembly instructions and Marlin 2.1.1 firmware for this mod. This firmware is for F103 and F303 chip. If you have the last version of Kingroon, you need compiled the firmware...

You must use it correctly, one end is for the input the other to the antenna (hence my modification at the SMA connector). End goal DJI Go with FCC Mod Strong directional antenna 4W booster per antenna Part list 1x Third party directionnal antenna...

I printed this https://www.thingiverse.com/thing:2172384 great nut/bolt/gasket combo to allow me to run PTEF tube straight from the drybox into my CR6-SE filament sensor using a modded version that allows PTFE straight into it (check my other things...

Future mods include a jumper for 12V/24V operation to prevent damaging the optocoupler's internal diode, and possibly adding a DC barrel jack. IMPORTANT: For 24V power, replace resistors with 1k ohm value. Also, check your Z endstop with a volt...

To build this mod, you will need: - 3 three-millimeter by twenty-millimeter socket head cap screws - 3 three-millimeter by twelve-millimeter machine screws - 3 washers (twenty-millimeter diameter) - 7 #6 or #8 flathead screws (three-quarters of an...

I like the stock part cooling fan and did't want to change it, but had a hard time looking for compatible mods so I decided to customize the stock cover to house a bigger hotend fan while maintaining the position, part cooling fan, aspect and size...

I created these to finish off my Cable Chain mods add cable management to the printer with cable ducts which replaces all the wiring zip ties with the same theme. There are 2 heights of cable ducts included, I've only used the "short" ones which fit...

ALSO I have attached the SW files (I don't normally do this but it provides everyone a better chance to modify) for anyone wanting to play with the design, I only ask that you post as a remix if you make mods so everyone can see and comment. I'm...

You can print the optional add-ons/mods for each side, such as the wallet-sized picture frame included. I'll continue to add more add-ons as time permits. I print this at .3 mm resolution PLA with 1.2 mm walls, featuring zero infill and support...

Hi, I want to share my mod of the E3D toolchanger, I had reliability issues with the tool change, so while tuning evrithing I came up with this and no more dropped tools!! (allignement of the tool/docking still important). Now I leave the printer...

------------------------------------------------------------ ***3D printed parts list:*** * One of each part, except: + 2x Dozer_Tilt_Cylinder + 10x Track_Middle_Wheels_MOD_2 + 33x Track_Pad_Left (+/- 1) + 33x Track_Pad_Right (+/- 1) + 2x...

meaning this one should fit in airsoft P90’s at least if they can hold Tokyo Marui AEG mags spring wise: my testing have been with round ball MCS spring at this point but if you like to try to use DTM mag springs then that is also possible with the...

This was primarily designed to fit this Titan Aero mount or my remix of it to the brilliant BLV mgn12 AM8 mod. Travel limits are about X = -9 Y = -22 for Volcano, X= -6, Y= -27 for v6. Update (12/4/2019): I've been using this mount for a while now...

Note: This will also work with the Frankenquest DAS mod for the Oculus Quest. I do not believe you need to worry about Quick Charge 3 capability with the Quest so should have more battery choices available as long as they are the same size. I like to...

compatibility note: this mag may not fit in all or any airsoft P90’s that can’t handle mags with a width of 50mm the RUNQI can’t work with this mag use the Classic model for that instead spring wise: my testing have been with round ball MCS spring...

compatibility note: this mag may not fit in all or any airsoft P90’s that can’t handle mags with a width of 50mm the RUNQI can’t work with this mag use the Classic model for that instead spring wise: my testing have been with round ball MCS spring...

The changes are incredibly small and easily covered up by mod/weathering, but i wanted them to be at least accessible ASAP. Update V3: Added presupported versions of the reactive armor skirts & turret. Update V4: Thanks to the awesome Gemma Long, she...

compatibility note: this mag may not fit in all or any airsoft P90’s that can’t handle mags with a width of 50mm the RUNQI can’t work with this mag use the Classic model for that instead spring wise: my testing have been with round ball MCS spring...

Vinyl cutting machines are expensive, and I have a printer, so I figured that I might as well try to mod my printer. I needed something that I could leave attached to the printer is compatible with a BL touch, and wouldn't get in the way when 3d...

These magnets help lock the lid in place, and allow me to more easily use the parts without glue, which makes it quite easy to swap any pieces quickly. I also wanted to hold more cards in my mod, so I used Joe Schmoe's 6 card remix as a strong...

Unluckily, these units require at least the Openbuilds X axis mod to be installed for optimal performance. Also included are Igus block mount ends because I had a set of cable chains without them. The X axis chain utilizes an Igus 10 x 15mm cable...

Further modding You may already be aware of rubber grommets which are used in plastic fermenting buckets. Select the STL named „grommet” to add the space (13mm) for such a thing. Other than that to improve sealing the mason jar you could order a...

Attached you can find the assembly instructions and Marlin 2.0.9.2 firmware for this mod. This firmware is for SMT32F1 chip. If you have the last version of Kingroon, you need compiled the firmware for SMT32F4 chip...