hobbyking durafly 3d models
2601 3d models found related to hobbyking durafly.thingiverse
This is a custom motor mount for the HobbyKing Prime Jet Pro 'Glue-n-go' series craft. The original was made from plywood, and had a screw hole layout suitable for larger plane-style motors. I wanted something that would fit a 2204 multirotor motor...
myminifactory
The Hobbyking Rattler is a great buggy but suffers from ESC over heating due to the lack of air flow (and the small ESC used in the car). The radio box on the car isn't air tight or water proof so I thought I'd make a cold air intake to get some air...
thingiverse
Made this OpenPilot bracket for the two 62mm-apart mounting holes on my HobbyKing "Firefly" 450 quadcopter frame. I think this frame is a clone of certain DJI frames, so if you have two holes in a line 62mm apart on your top plate, you should be set...
thingiverse
Hobbyking Skyraider alternative replacement prop and tail-wheel assembly, I have successfully flown using these parts multiple times. The nubbin goes on the prop shaft first followed by the prop and then secured with the original washer and nut. I...
cults3d
Hobbyking Skyraider alternative replacement prop and tail-wheel assembly, I have successfully flown using these parts multiple times. The nubbin goes on the prop shaft first followed by the prop and then secured with the original washer and nut. I...
thingiverse
Perhaps that's why hobbyking discontinued the model. If the wings ripped off your model and fluttered slowly to the ground while the fuselage was doing an impression of a lawn dart you may well have a broken firewall. Usually I would just cut one...
thingiverse
The Hobbyking Lancaster bomber has a roughly 8mm gap between the front of the nacelles and the spinner, which is quite unsightly. This will fill the gap while still providing an opening for a wrench on the prop driver when tightening the prop. ...
thingiverse
The Hobbyking Rattler is a great buggy but suffers from ESC over heating due to the lack of air flow (and the small ESC used in the car). The radio box on the car isn't air tight or water proof so I thought I'd make a cold air intake to get some air...
thingiverse
This landing gear replacement is for the Hobbyking ME163 red version. Maybe it will fit for the original "green" version too. At the moment, it is a work in progress, meaning the upper part may be to thick for the ME163. My first version was too...
thingiverse
Rear Suspension Arm for the HobbyKing Desert Fox Modeled as close to the original as possible, which makes for an ugly print with supports. It's "good enough", the length and width and holes are all in the right spot, the structure is just offset a...
thingiverse
I wanted to fit a Zippy compact 2200 mah battery ( https://hobbyking.com/fr_fr/zippy-compact-2200mah-3s-25c-lipo-pack.html) as it is 10.9 mm long, it could fit just in front of the wheel were the fuselage is the widest, but i needed a special...
thingiverse
I use it in my Durafly Tundra V2 for my 3S 2200mAh battery. It makes it easy accessible and fixes the cog. The battery is fixed with a rubber band to the battery tray. The tray itself slides into the tray-mount, wich is glued to the airplane. The...
thingiverse
This is a complete new designed top part for the Quanum Trifecta sold by Hobbyking. This part will fit using the original screws without modifying the original frame. It fits especially for a specific flightcontroller (AfroFlight 32), receiver (FrSky...
thingiverse
The Hobbyking Slow Stick is a really fun plane to fly. After a few crashes more than a few pieces needed replacement, so I started to design my own. All the pieces are designed to use M3 screws and nuts instead of glue to fix them, so it's easier to...
thingiverse
** work in progress ** - Tricky to fit up the T-38 canopy hole - A little tall, option to mount camera arm pointing forward, rotate up to install Here is a compact pan/tilt rig. I designed it to work on multiple airplane and wing...
thingiverse
screw on spinner for stock motor uses 2 2mm or less screws to hold the spinner to the back plate fits apc 11x7 and others this is a remix but im sorry i cannot remember who is the original designer
thingiverse
I wanted to upgrade Tundra’s thin landing gear frame, so I designed landing gear fairings. The fairings also support the landing gear and with fairings the landing gear can handle more tougher landings without bending. Fairings are attached with...
thingiverse
pla or petg make a hole on a top of nose plane for slide this one
thingiverse
Not quite a remix but based on work done by Rob Thomson. https://www.thingiverse.com/thing:1362079 Mk1: Still a work in progress. Use SG90 servo for the tilt. There are two options for the pan servo (SG90 or TGY180). ...
thingiverse
Replacement for the aileron covers. Made with Tinkercad. ...No rocket science involved.
thingiverse
I tried SaKes' version of the mount and wasn't quite satisfied. So did a few changes. But thank him for the idea! Added a slope also on another side of the spar lock for better hold and no glueing required. Also moved spar lock's hole a bit...
thingiverse
Mount for Matek plane FC's to put into the rear bay. Easy to lock with two M3 bolts. ... I use [Ruthex M3 threaded heat inserts](https://www.amazon.de/ruthex-Gewindeeinsatz-St%C3%BCck-Gewindebuchsen-Kunststoffteile/dp/B08BCRZZS3?th=1) there, so the...
thingiverse
This is a replacement for the standard latch on the excalibur. I used a 3mm knurl insert nut in the center. ...Print Settings Printer Brand: Prusa ...
thingiverse
Print @ 210° nozzle / 60 Bed Edit: Use V2 with big Lipo like 500mah
thingiverse
This is a mount for a Runcam Split mini. It is made to fit into one of the holes in the bottom of a tundra, to give an underneath view with the landing gear in shot. Provides access to the usb port, sd card slot, and buttons. Prints in two pieces...
thingiverse
I had a hard landing while on floats with my Tundra. The plastic mounts separated from the foam floats and one cracked, while another sank to the bottom of the lake. I've modeled a replacement based off the original. Measured with calipers and...
prusaprinters
<p>This is a replacement for the standard latch on the excalibur. ...I used a 3mm knurl insert nut in the center.</p> <h3> Print Settings</h3> <p><strong>Printer Brand:</strong></p> <p>Prusa</p> <p><p class="detail-setting printer"><strong>Printer:...
thingiverse
landing gear retainers for the tundra v2 may require a little sanding...print 1 then mirror for the other side
thingiverse
This piece goes on the plane just like the original piece. Slots easily into place. ...Keeps it nice and tight and secure.