hose bulkhead fitting 3d models

Fitting for connecting 1/2 tube to 16 mm hose.

Remix to fit a 4mm hose on the barb side.

Pneumatic fitting for port G1/4 & hose 4 mm.

Pneumatic fitting for port G1/4 & hose 4 mm.

Brass hose fitting for 3/8" ID hose. Ferrules on barb end hold hose from slipping off. Use of hose clamp helps prevent leaks. 1/2" Male NPT thread on opp end. ...7/8" hex

needed a bulkhead barb fitting for a project so here it is . ...12mm threads 10mm large hose barb 8mm small hose barb

needed a bulkhead barb fitting for a project so here it is . ... 12mm threads 10mm large hose barb 8mm small hose barb

A custom-made hose barb fitting is used in my car for the turbo boost controller. The threads are 1/8" NPT, and the hose barb accommodates approximately 5/16" rubber vacuum hoses, with compatibility for 1/4" hoses as well. ...I printed the fitting at .1...

Dillon 550 spent primer cup with 1/2" hose barb Made a stronger connection to the hose fitting V2 has the connection to the press more offset and shorter

... use supports so best to print with supports if you can). ... I downloaded a 1/2" Barbed Hose fitting then scaled it up by 150% to get to 3/4" so it should be correctly sized. ...Then I combined it with a garden hose fitting to get the final result.

Liked the design by PeterBrit, but wanted to be able to print with no supports, and needed to make hole bigger to fit over the rest of the hose crimp and fittings.

Modification of SVideo's airlock design; fits a 1.75" vacuum hose. Included a wingnut to tighten securely around the hose, otherwise it falls off. Use an M4 x 25mm bolt, nut, and washer. Make sure you use a strong glue and print the wingnut in a...

- 1/2'' male BSP (British Standard Pipe) parallel threaded fitting (about 12.7mm) - 8mm INNER diameter hose adapter - for 18mm wrench HoseAdapt127.stl can be printed without any supports because a support structure is already modeled into the .stl...

I had stepped on and broken many of the fittings on the ends of my hoses, and wanted a replacement that fit ANY 2 inch connection - not just a particular brand. Through trial and error I ended up with one fitting with a OD taper that fits into any...

Hose joints with hex fitting tapered Outside diameter 0.8 mm Inside diameter 0.4mm Print tested on Photon mono x6K with nFep film In profile available some different diameters 1.6, 1.4, 1.2, 1.0, 0.8

This should fit a hose with a 1.25" OD and a 1.0625" (1 1/16") ID This allows you to use a hose like the one that comes with the Home Depot Bucket head for approximately $24+ the cost of a 5-gallon bucket. A longer hose is recommended vs the stock...

After 12 years of seasonal use, the flexible plastic hoses on my 3-quart LiquiVac motor oil extraction device had become brittle and no longer stayed securely attached to their fittings. Although the LiquiVac remains available for purchase from...

This adapter provides an M25 Male on one end and a Male Garden Hose Thread on the other, allowing the jug to be used for pouring into another container (say, an RV) and not just dispensing. ...Be sure to only use garden hoses marked for Potable water!

It can then be attached to a standard friction fitting for larger diameter vacuum hose with an outside diameter of 40mm. ... \ The internal face in this adapter is 40.5mm at the mount, narrowing to 39.5mm internally Fusion360 file available on...

Hose joints with hex fitting tapered Outside diameter 1.0 mm Inside diameter 0.6mm Warning: nut fitting support with a wall 0.1-0.2 mm Print tested on Photon mono x6K with nFep film In profile available some different diameters 1.6, 1.4, 1.2, 1.0,...

Hose joints with hex fitting tapered Outside diameter 1.2 mm Inside diameter 0.8mm Warning: nut fitting support with a wall 0.1-0.2 mm Print tested on Photon mono x6K with nFep film In profile available some different diameters 1.6, 1.4, 1.2, 1.0,...

Hose joints with hex fitting tapered Outside diameter 1.4 mm Inside diameter 1.0mm Warning: nut fitting support with a wall 0.1-0.2 mm Print tested on Photon mono x6K with nFep film In profile available some different diameters 1.6, 1.4, 1.2, 1.0,...

Hose joints with hex fitting tapered Outside diameter 1.6 mm Inside diameter 1.2mm Warning: nut fitting support with a wall 0.1-0.2 mm Print tested on Photon mono x6K with nFep film In profile available some different diameters 1.6, 1.4, 1.2, 1.0,...

I suggest utilizing the upgraded model with threads to securely attach the flex hose: https://www.thingiverse.com/thing:4061125 This adapter connects a flexible 4" dust collection hose directly to standard 4" PVC fittings. It's essential to apply...

Kitbashed ¼ NTP male to male ½ hose barb.

It has a recess to fit an O-ring with a maximum of 17mm of diameter by 2 mm thick. The ridges large and small diameters are, respectively 7mm and 5.5mm. The fluid passage has 3.5mm of diameter. ... It was printed with the threaded side up, using...

A big thanks to codemite for the source for this: Garden Hose Thread Profile - GHT (0.75-11.5 NHR) Female and Male https://www.thingiverse.com/thing:2563403 by codemite October 01, 2017 I was able to add a pipe section to the Female 3/4" Garden Hose...

This is a simple 8 mm beer hose push-In fitting circlip. I've tested it with Duotight 8mm fittings (highly recommend, super high quality fittings) and DMT / DMfit 8mm fittings, and it works pretty well for both. I recommend printing this using...

If you're concerned about fittings pulling apart or having leaks, this one has a rim that encases the other flange. I keep one of these on the main hose of my dust collector, with 4143200 on everything else. The lips at the top edges of the...

Hose Bandage holder and marker holder Printed in PLA but go for whatever you like.