hovergames 3d models

... ### This design is a work in progress Video : https://www.youtube.com/watch?v=xLfMEuMjAZE Documentation : https://www.gitbook.com/book/nxphlite-team/prototype-nxphlite/details Website: https://www.nxp.com/uav Website: https://www.nxp.com/HoverGames

For Hovergames

GoPro mount for the NXP Hovergames drone.

... is to allow for neat mounting of the ESCs onto the drone’s bottom plate, secured only by cable ties (and no double sided tape). This is part of a three part design: HoverGames Arm Mount - Left HoverGames Arm Mount - Right HoverGames Arm Mount - None

... way compared to the NXP HoverGames instructions. The standard way to mount the telemetry radio is to use double sided tape and a single cable tie. This is part of a two part design: HoverGames Radio Mount - Top HoverGames Radio Mount - Bottom

... is to allow for neat mounting of the ESCs onto the drone’s bottom plate, secured only by cable ties (and no double sided tape). This is part of a three part design: HoverGames Arm Mount - Left HoverGames Arm Mount - Right HoverGames Arm Mount - None

... way compared to the NXP HoverGames instructions. The standard way to mount the telemetry radio is to use double sided tape and a single cable tie. This is part of a two part design: HoverGames Radio Mount - Top HoverGames Radio Mount - Bottom

... is to allow for neat mounting of the ESCs onto the drone’s bottom plate, secured only by cable ties (and no double sided tape). This is part of a three part design: HoverGames Arm Mount - Left HoverGames Arm Mount - Right HoverGames Arm Mount - None

It was built as part of the Guardian Angel submission for the HoverGames Challenge 1: Fight Fire with Flyers challenge. ...The purpose of this bracket is to securely mount the GPS antenna, in an improved way compared to the NXP HoverGames instructions.

# HoverGames Mounting plate for S500 drone frame The HoverGames drone uses an experimental flight controller (FMU) from NXP Semiconductor that is Linux Foundation Dronecode.org PX4.io software compliant. It follows Dronecode.org connectorization...

... ###This design is a work in progress Video : https://www.youtube.com/watch?v=xLfMEuMjAZE Documentation : https://www.gitbook.com/book/nxphlite-team/prototype-nxphlite/details Website: https://www.nxp.com/uav Website: https://www.nxp.com/HoverGames

It was built as part of the [Guardian Angel](https://www.hackster.io/sjvincent/guardian-angel-90dd83) submission for the [HoverGames Challenge 1: Fight Fire with Flyers](https://www.hackster.io/contests/hovergames) challenge. The purpose of this...

It was built as part of the [Guardian Angel](https://www.hackster.io/sjvincent/guardian-angel-90dd83) submission for the [HoverGames Challenge 1: Fight Fire with Flyers](https://www.hackster.io/contests/hovergames) challenge. The purpose of this...

- Works on the LJI X4 frame used in NXP HoverGames drone, HGD-TELEM433 in combination with KIT-HGDRONEK66 - https://www.nxp.com/KIT-HGDRONEK66 - HGD-TELEM433 - Holybro 433 MHz telemetry radio set (Europe) (tested!) - HGD-TELEM915 - Holybro 915 MHz...

The purpose of these two brackets is to securely mount the GPS antenna and telemetry radio, in an improved way compared to the [NXP HoverGames](https://nxp.gitbook.io/hovergames/userguide/assembly/top-plate-gps-telemetry-and-fmu) instructions. The...

It was built as part of the [Guardian Angel](https://www.hackster.io/sjvincent/guardian-angel-90dd83) submission for the [HoverGames Challenge 1: Fight Fire with Flyers](https://www.hackster.io/contests/hovergames) challenge. The purpose of this...

It was built as part of the Guardian Angel submission for the HoverGames Challenge 1: Fight Fire with Flyers challenge. The purpose of this bracket is to allow for the neat mounting of the Pixy2 and the NXP HGD-Heatsensor. It is designed to tightly...

It was built as part of the Guardian Angel submission for the HoverGames Challenge 1: Fight Fire with Flyers challenge. The purpose of this bracket is to allow for the neat mounting of the NXP RDDRONE-IOT board, which in turn holds the NXP Rapid IoT...

-=-=- This is a shell case to protect the www.hovergames.com NavQ companion computer. The top should allow the Coral camera mount to screw in and provide clearance on the backside for the screw heads. Note that the camera mount is optional as there...

... ...This FMU (Flight management Unit) runs PX4 opensource flight stack, and is used in HoverGames coding challenge. More information is available at www.HoverGames.com Website: https://www.nxp.com/HoverGames Website: https://nxp.gitbook.io/HoverGames

This is my design for a much stronger foot for the legs of the hovergames drone.

Clear Design Frame Ring. ... - Works on the LJI X4 frame used in NXP HoverGames drone, KIT-HGDRONEK66 - https://www.nxp.com/KIT-HGDRONEK66

This is a case I designed for the NavQ for the NXP hovergames. ...I may still make some improvements so I will upload the new files when ready.

Modified from https://iroboteducation.github.io/create3_docs/hw/print_compute/#navqplus-by-nxp Modifications were to cover the 1Gb network port that is not populated on the Hovergames 3 edition of the board. This object was made in Tinkercad. ...Edit...

Cad files of aditional parts attached to NXP Drone.

SMA mounting Hardware for Drones. ... Compatible with NXP Hovergames. ... 30mm clearance under the Mounting hole.

This is a double sided mount for mounting two gopro snap-in items onto the NX Hovergames drone. ...It slides over the mounting rails.

... ... It clips onto the 10mm diameter x 60mm spacing rails of the HoverGames drone The HoverGames drone uses an experimental flight controller (FMU) that runs PX4.io flight stack software, and others. It follows Dronecode.org connectorization standards.

This is a battery bracket so you can mount the battery solidly underneath the NXP Hovergames drone. ...Then the 2 carbon fibre rods are mounted and the camera can be mounted underneath the battery.

Raspberry Pi Zero case with a mount for the HoverGames Drone. You will need a couple of small screws/nuts. ...The holes are spaced apart appropriately for mounting the DROK - 90010 Buck Converter to the bottom side of the case.